5800 RM-356 не включается
#1
Здравствуйте!
ТА после удара.
При включении висел в 50мА. После подключения к программатору было выявлено, что он не видит флеш. После перекатки процессора и флеш, а также замены коннектора АКБ всё заработало. Собрал в корпус и ТА не включается (потребление 160 мА и всё).
Больше проблем не вижу. Локал есть, селф-тесты в норме. Прошивается, полностью стирал и прошивал через ColdFlash. Когда заходит в локал - отображается режим, версия, всё как положено. После перехода в Normal - 160 мА и висит сикунд 30, потом отключается.
Лог селф-тестов, проверки сертов и инфо без шлейфа sec.камеры:
Код:
Initializing Tests...
IMEI : 353205035**** , Phone : RM-356 Nokia 5800 XpressMusic
Get keys...
PASSED | ST_TAHVOINT_TEST
PASSED | ST_UEM_CBUS_IF_TEST
PASSED | ST_EAR_DATA_LOOP_TEST
PASSED | ST_SIM_CLK_LOOP_TEST
PASSED | ST_SIM_IO_CTRL_LOOP_TEST
PASSED | ST_SIM_LOCK_TEST
PASSED | ST_SECURITY_TEST
PASSED | ST_PWR_KEY_TEST
PASSED | ST_CURRENT_CONS_TEST
PASSED | ST_BACKUP_BATT_TEST
->ERROR | ST_RADIO_TEST
PASSED | ST_HOOKINT_TEST
PASSED | ST_BTEMP_TEST
PASSED | ST_MBUS_RX_TX_LOOP_TEST
->ERROR | ST_AMB_LIGHT_SENSOR_TEST
PASSED | ST_IIC_TEST
PASSED | ST_EXT_DEVICE_TEST
PASSED | ST_CDSP_SLEEPCLK_FREQ_TEST
PASSED | ST_CDSP_SLEEPCLOCK_FREQ_TEST
PASSED | ST_CDSP_RF_BB_IF_TEST
PASSED | ST_CDSP_RF_SUPPLY_TEST
PASSED | ST_CDSP_TX_IQ_TEST
PASSED | ST_CDSP_TXC_DATA_TEST
PASSED | ST_CDSP_PWR_DETECTOR_BIAS_TEST
PASSED | ST_CDSP_RX_PLL_PHASE_LOCK_TEST
NOT RUN | ST_CDSP_TX_PLL_PHASE_LOCK_TEST
NOT RUN | ST_CDSP_WCDMA_TX_POWER_TEST
NOT RUN | ST_CDSP_RX_IQ_LOOP_BACK_TEST
NOT RUN | ST_CDSP_GSM_TX_POWER_TEST
PASSED | ST_KEYBOARD_STUCK_TEST
PASSED | ST_LPRF_IF_TEST
PASSED | ST_CAMERA_IF_TEST
PASSED | ST_CAMERA_ACCELERATOR_TEST
->ERROR | ST_SEC_CAMERA_IF_TEST
PASSED | ST_LED_FLASH_TEST
PASSED | ST_CAMERA_AUTOFOCUS_TEST
PASSED | ST_LPRF_AUDIO_LINES_TEST
PASSED | ST_MAIN_LCD_IF_TEST
PASSED | ST_TOUCH_STUCK_TEST
PASSED | ST_BT_WAKEUP_TEST
PASSED | ST_WLAN_TEST
PASSED | ST_BT_WLAN_COEXISTENCE_TEST
PASSED | ST_TOUCH_IF_TEST
PASSED | ST_ACCEL_IF_TEST
PASSED | ST_LCD_CONTROLLER_TEST
PASSED | ST_VIBRA_TEST
NOT RUN | ST_USB_LOOP_TEST
UNKNOW | ST_RADIO_TEST
PASSED | ST_TVOUT_IF_TEST
PASSED | ST_IO_EXPANDER_IF_TEST
SelfTests end
Done!
Elapsed: 00:00:41
Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
CMLA Key status : CMLA key is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------
PA_SimLock Version :
PA_SL2 phone detected
Done!
Reading Phone Info....
Connected phone - Nokia 5800 XpressMusic
Software ver : V ICPR72_10w29_tube1 24-05-11 RM-356 (c) Nokia
IMEI : 35320503**********
Ape Ver : V 60.0.003
APE Var : V 60.0.003V 60.0.003 V 60.0.003
APE ADSP: 256
DSP Ver : ICPR72_10w26p1
APE Test: eno_version
PPM :
CNT : v 50.2010.06.1_001_000_U01 17-03-10 vanilla RM356
Product SN : CCI309169
Product code : 0574888
Base Prd.code: 0552692
Long Prod.SN : 0
Hardware info=======
HWID : 1101
Retu : 15
Tahvo : 22
Batery: 3718 mV
APE HW: 256
Lock info ===========
IMEI : 353205035******
IMEI spNet : 3A 35 02 05 53 20 78 02
IMEI svNet : 33 35 02 05 53 20 78 72 F4
Conf key : 0000000000000000
Provider key : 2440700000000000
Country : Finland
Operator : NOKIA (Open)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7
LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created
SDD key status : Ok
CMLA Key status : Ok
SimLock status : Ok
Security status : Ok
PA_SimLock Version :
PA_SL2 phone detected
User code : Crypted
UserDataExLevel : Low [Gallery] , FullFlash method
Done!
Лог прошивки:
Код:
Core : v1.55 , FlashEngine : v3.3
Selected FlashSettings : Cold Flash
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : RM-356_60.0.003_prd.core.C00
PPM : RM-356_60.0.003_prd.rofs2.V05
PPM2 : RM-356_60.0.003_C01_prd.rofs3.fpsx
CNT : RM-356_60.0.001_026_000_U01.uda.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
- > Force ColdFlash mode
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000010000022600010006400C192101031103
CPU ID : RAPIDOv11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 15B0010370750052FAFE87BCB67B0B26E8700429
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: 4B9B75103E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 12.8.0
Processing RAWLOADER...
FLIC : 004000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 12.8.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:05
Reopening the connection...
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : Blank (Erased or HW failure)
CFL: phone is in flash mode
===Flashing [MCU]===
Erase : Processing RM-356_60.0.003_prd.core.C00
Partitioning....
Partitioning Ok...
Erasing....
Erasing Data....
Erase area : 0x00040000 - 0x00082FFF , CMT , NAND
Erase area : 0x00083400 - 0x003FFFFF , CMT , NAND
Erase area : 0x00400000 - 0x007FFFFF , CMT , NAND
Erase area : 0x00800000 - 0x00D5FFFF , CMT , NAND
Erase area : 0x00D60000 - 0x09E5FFFF , CMT , NAND
Erase Partition
Partition 0x0A
Erase Ok...
TIME : Erase time : 00:00:01
CFL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
Write : Processing RM-356_60.0.003_prd.core.C00
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*ENO]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 450 blocks
TIME : Write time : 00:01:40
MCU Write done
CFL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
===Flashing [PPM]===
Erase : Processing RM-356_60.0.003_prd.rofs2.V05
Erasing....
Erasing Data....
Erase area : 0x07180000 - 0x0915FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
Write : Processing RM-356_60.0.003_prd.rofs2.V05
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 111 blocks
TIME : Write time : 00:00:25
PPM Write done
CFL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
===Flashing [PPM2]===
Erase : Processing RM-356_60.0.003_C01_prd.rofs3.fpsx
Erasing....
Erasing Data....
Erase area : 0x09160000 - 0x09E5FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
Write : Processing RM-356_60.0.003_C01_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 6 blocks
TIME : Write time : 00:00:01
PPM Write done
CFL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
===Flashing [CNT]===
Erase : Processing RM-356_60.0.001_026_000_U01.uda.fpsx
Erasing....
Erasing Data....
Erase area : 0x09E60000 - 0x0F71FFFF , CMT , NAND
Erase Ok...
TIME : Erase time : 00:00:00
CFL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
Write : Processing RM-356_60.0.001_026_000_U01.uda.fpsx
Total writen 29 blocks
TIME : Write time : 00:00:07
CNT Write done
CFL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
CFL: Close_Session
Content: 000300000000020000000200000000
CFL: Reboot
Flashing done!
Total flash time : 00:02:17
Reboot phone now...
Reading Phone Info....
Connected phone - Nokia 5800 XpressMusic
Software Info: V ICPR72_10w29_tube1 24-05-11 RM-356 (c) Nokia
IMEI: 12345610654321?
Ape Version: V 60.0.003
Product code:
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Battery voltage is enough for start
AfterFlash operations done ;D
Done!
Последние файлы
