xotel sdelat rusifikaciyu ,posle etogo telefon ne vkluchaetsa, tel na proce mt6228, INFINITY ne pishet sdelanniy im je buckup, proshu pomoshi

прошу помоши ,неуйели никто не мойет помоч и вот что пишет

Loading file v.02...
nand_[BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN]_firmware_20090512-165856.B4M.bin loaded
identification#1 protocol ver: 04
ver. sw 1: BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN
ver. sw 2: BBK, 1AA8E02D
Loaded file w/protection: security area (code #1)

==== log: [12.05.2009 19:45:32] ====
COM5 [VCP0] selected
module v2.82
Device: Autodetect 6228-6230 NAND
Checking data, wait...
Action: write NAND flash
read mode: 01
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
id-page1 Ok
end mark #1 found
nfi area detection finished: Ok
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6228:8A02:8A02]...
CPU: MT6228
high speed boot On
chip: 0031C09:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.02
cpu-id: 07
loader: 3.0840.00.00
NAND id: 98F19095
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
external ram: 00000000
finalize connection...
done
emi configuration...
ram size: 02000000
emi configuration done
ram test...
pass 1...
pass 2...
pass 3...
pass 4...
done
NOR: 0000:000000000000 [00000000]
NAND: 0098:00F100900095 [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
460800
Set baud Done
Identification ...
ram test...
pass 1...
pass 2...
pass 3...
pass 4...
done
reading bootloader structure area (00080000 bytes)...
detecting bootloader structure...
warning: probably flash chip completely erased, no bootloader found
nfi area detection finished: failed
detecting bootloader structure by source file...
source data: page only
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is damaged, recalculation required
identification#1 detection finished
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.E767D607.[BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.E767D607._BBK2 8_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5_.rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.E767D607.[BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\i d.E767D607._BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BI N_D21F57E5_.rpl
====================
warning: unknown identification#1 structure: BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN_D21F57E5
error: Unknown firmware detected (v.2.82, database date: ), user action required:
1. download latest software from support area and try again
2. if no still luck follow the next procedure:
- find good working phone with the same firmware:
BBK28_06B_PCB04_GPRS_MT6228_S02.BBK.BIN
- make "Read full flash" operation
- send "system_log_..." file to support:
- send flash backup files to support:
- include in your e-mail full text from phone back label (phone name etc.)
- be little bit patient and wait update
====================
You can flash phone now but can not finalize it.
In most cases phone CAN NOT power-on.
Do you want to continue anyway ?
Identification Done
Write ...
00006000 bytes sent
write core area 1 of 3...
00413C00 bytes sent
write core area 2 of 3...
00CAB000 bytes sent
write core area 3 of 3...
002EE800 bytes sent
Write Done
Finished, time used: 766 sec
Remove/Install battery now

отправил buckup но нет ответа

Выложите прошивку на файлообменник и добавьте к своему сообщению ссылку на него.

p.s. Орфографию и пунктуацию никто не отменял, если и в будущем от Вас будут такие посты -буду вынужден Ваши сообщения отправить в Мусорник, а Вас - в бан за несоблюдение правил.

http://www.4shared.com/file/10569241.../BBK_i399.html