Samsug E708+ увалил форматом
#1
Тело пришло с перегрузом с сим картой. Подключил к инфинити, по глупости фулл не слил и решил сделать формат. Во время формата выдало ошибку, в итоге тело не включается.
Вот лог инфинити
COM5 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: reset
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6219:8A01]...
CPU: MT6219
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: B000B101000000:B000B100000000
flash: Sharp Intel std [def 0008x002000 007Fx010000] 8Mb
detecting chip #01 in region #00...
flash: B000B004000000:B000B000000000
flash: Sharp Intel std [def 007Fx010000 0008x002000] 8Mb
detecting chip #02 in region #00...
flash: B000B101000000:B000B100000000
flash: Sharp Intel std [def 0008x002000 007Fx010000] 8Mb
detecting chip #03 in region #00...
flash: B000B004000000:B000B000000000
flash: Sharp Intel std [def 007Fx010000 0008x002000] 8Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud...
921600
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: B000B101000000:B000B100000000
flash: Sharp Intel std [def 0008x002000 007Fx010000] 8Mb
detecting chip #01 in region #00...
flash: B000B004000000:B000B000000000
flash: Sharp Intel std [def 007Fx010000 0008x002000] 8Mb
detecting chip #02 in region #00...
flash: B000B101000000:B000B100000000
flash: Sharp Intel std [def 0008x002000 007Fx010000] 8Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 02/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
.
detection phase #2...
.................................................. .................................................. ............................
warning: identification#1 information not found, possible reasons:
.old firmware type w/o identification#1 data
.damaged firmware
.damaged hardware
if phone works fine just ignore this warning
detect device identification#1 finished
detect device identification#2...
detection phase #1...
.
warning: optional information not found
detect device identification#2 finished
detecting eeprom/ffs area in 2 chip(s)...
standard eeprom/ffs offset assigned: 00E00000
flash: B000B101000000:B000B100000000
checking area[00000000]: 00000000-007FFFFF...
flash: B000B004000000:B000B000000000
checking area[00800000]: 00000000-007FFFFF...
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00E00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00200000
ffs chip: 01
eeprom/ffs area: 00800000:00600000-007FFFFF
flash: B000B101000000:B000B100000000
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
formatting...
flash: B000B004000000:B000B000000000
error: error# 00002222
80:7[00]: Device is busy; program or erase cycle in progress; SR[0] valid.
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
02:1[01]: Block locked during program or erase; operation aborted.
error: flash erase error: 00E10000
error: error# 00002222
80:7[00]: Device is busy; program or erase cycle in progress; SR[0] valid.
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
02:1[01]: Block locked during program or erase; operation aborted.
error: flash erase error: 00E20000
Write Fail
Finished, time used: 40 sec
Remove/Install battery now !
Пробовал с трупа считывать фулл, фулл считывается нормаль.
Есть фулл слитый с мертвого тела, если поможет могу выложить или выслать на мыло.