Проблемы на моем компьютере - софт Infinity не работает или конфликтует?
#1
Проблема состоит в том что софтина инфинити не хочет корректно работать. На компе стоит сервис пак 2, поставил новые дрова wd_pl2303_v20011_v20024_BRIDGE и PL2303_2.0.2.8, эффекта никокого не дало. На компе висит еще Xintel и JAF. Коннекчу через ксинтел (он находит распиновку).
вот лог
COM4 [Serial2] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
eeprom backup enabled, it may takes several minutes !
Action: read NOR flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6226:8A02:8A01]...
CPU: MT6226
chip: 0031:A40E:3CC3
high speed disabled
boot step size: 0002
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
115200
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 290000EA18F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [enhanced] generation
warning: wrong data size at 0x002C1230, retry...
warning: wrong data size at 0x002C1230, retry...
warning: wrong data size at 0x002C1230, retry...
warning: wrong data size at 0x002C1230, retry...
warning: wrong data size at 0x002C1230, retry...
warning: wrong data size at 0x002C1230, retry...
warning: wrong data size at 0x002C1230, retry...
warning: wrong data size at 0x002C1230, retry...
warning: wrong data size at 0x002C1230, retry...
error: too many retries during read operation
error: no any expected answer
error: can't read security area#1
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
warning: optional information not found
detect device identification#2 finished
detecting eeprom/ffs area in 1 chip(s)...
standard eeprom/ffs offset detected: 00800000
error: no any expected answer
error: no any expected answer: wrong answer after chip id request
error: no any expected answer
error: no any expected answer
error: no any expected answer: wrong answer after chip cfi request
error: no any expected answer
error: no any expected answer: wrong answer after chip id request
Can't detect eeprom/ffs area
Do you want to use standard ffs address: 00800000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs address selected by user
detecting eeprom/ffs size...
eeprom/ffs size: 00800000
ffs chip: 00
eeprom/ffs area: 00000000:00800000-00FFFFFF
Finished, time used: 90 sec
Remove/Install battery now !