Тестирование Новых возможностей BEST'a -II [Архив] - Страница 3

Просмотр полной версии : Тестирование Новых возможностей BEST'a -II

Страницы : 1 2 [3]

Mumang

04.07.2011, 07:01

Есть такой телефон , но высылать далековато, там джойстик неисправен насколько я знаю у камрада по ремонту ноутов, если на опыты нужен обсудим в ЛС или в аське. Всё равно валяется.

bmw

05.07.2011, 11:11

Сейчас гланое такой телефон найти. Попробую за неделю найти и разобраться, это очень старый телефон и его режим прошивки отличается от остальных.Не только с Е50 проблемы, у меня почти все бб5 на новых версиях шьются до конца, потом входят в тест мод и дальше прога их просто не видит, и не видит их остальной софт. Видятся потом только из включенного состояния, приходится МТ-боксом из включенного состояния делать все сбросы, не переводя в тест мод. Может это связано с недавней переустановкой винды, что-то криво поставилось... Но ведь при прошивке тем же МТ-боксом тела потом нормально видятся из тест/локал мода.
П.С. Тела включаются и работают нормально.

ildar80r

05.07.2011, 11:19

Не только с Е50 проблемы, у меня почти все бб5 на новых версиях шьются до конца, потом входят в тест мод и дальше прога их просто не видит, и не видит их остальной софт. Видятся потом только из включенного состояния, приходится МТ-боксом из включенного состояния делать все сбросы, не переводя в тест мод. Может это связано с недавней переустановкой винды, что-то криво поставилось... Но ведь при прошивке тем же МТ-боксом тела потом нормально видятся из тест/локал мода.

Аналогичная ситуация. Мучился с 6300. В итоге сделал MX-key. Грешу на винду, тоже недавно переустановил.

Mumang

05.07.2011, 13:12

Нет это не винда точно, у меня на последних версиях так бывает тоже когда по usb шьёшь, но как-то непостоянно что-ли, то всё в норме, то висит на постфлешинге и сбросы не делает, сначала на Comodo грешил, потом отключал его, толку нет, как-то выборочно глючит.

JayDi

05.07.2011, 15:13

Да нихрена там не менялось, нечему там глючить.

Mumang

05.07.2011, 15:24

Ну тогда на глюки портов материнки можно списать, просто винда в test mode не видит ТА после флеширования раз через раз и соответственно Best и висит ничего не делает.

JayDi

05.07.2011, 15:34

Сорри, просто последние дни куча проблем, нервы. Проверю, три компа+бук есть и порядка 35 телефонов. выложу логи после со всех.

По поводу 6300 и контактов в нем -
баг в ини, хз как он там появился
сменить строчку RM-217 на
RM-217=000000

ZArchi

05.07.2011, 15:38

Ну тогда на глюки портов материнки можно списать, просто винда в test mode не видит ТА после флеширования раз через раз и соответственно Best и висит ничего не делает.
Подтверждаю, имеет место быть, нужно подождать минуту или выбрать опять подключение в интерфейсе BESTa.

JayDi

05.07.2011, 15:56

Вообще из-за МТР-драйвера может быть такое, но, тут зависит от того, что первым ставится - Phonet или МТР - если phonet - тел увидится сразу, при мтр - может быть до двух минут.

kihmet

05.07.2011, 16:48

Успешно прошита Nokia X7-00 RM-707
BEST 1.23

DEAD Mode:
Connect phone on selected interface...

Core version : 1.23 , Rev : 4.8

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : RM-707_021.013_79.92_prd.core.fpsx
PPM : RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
PPM2 : RM-707_021.013_00.01_79.92_prd.rofs3.fpsx
CNT : RM-707_021.013_U01.01_79.92.uda.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
: Bootrom Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00001040
EM1 ID: 00001030
PUBLIC ID: 1060021961F75840B3DADC4549CD0FAC9BF141EC
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.16.0
Processing RAWLOADER...
FLIC : 006000EC
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.16.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
IMEI : 35625704XXXXXXX
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Cert Read done!

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : D:\GSM\BEST\Soft\InfinityBox_install_BEST_v1.23\Ba ckup\Cert\35625704XXXXXXX_CRT.rpl

===Flashing [MCU]===
Erase : Processing RM-707_021.013_79.92_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing RM-707_021.013_79.92_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 505 blocks
TIME : Write time : 00:00:17
MCU Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

===Flashing [PPM]===
Erase : Processing RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 196 blocks
TIME : Write time : 00:00:07
PPM Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

===Flashing [PPM2]===
Erase : Processing RM-707_021.013_00.01_79.92_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-707_021.013_00.01_79.92_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 2 blocks
TIME : Write time : 00:00:00
PPM Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

===Flashing [CNT]===
Erase : Processing RM-707_021.013_U01.01_79.92.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing RM-707_021.013_U01.01_79.92.uda.fpsx
Total writen 521 blocks
TIME : Write time : 00:00:22
CNT Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

ADL: Close_Session
Content: 000300000000010000000100000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:51
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia X7-00
Software Info: V 92_11w15.4 17-05-11 RM-707 (c) Nokia
IMEI: 35625704XXXXXXX
Ape Version: 021.013
Product code: 059G558
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Set phone to Normal mode...
AfterFlash operations done...
Done!

Elapsed: 00:01:24
Connect phone on selected interface...

[B]Normal Mode:
Core version : 1.23 , Rev : 4.8

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : RM-707_021.013_79.92_prd.core.fpsx
PPM : RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
PPM2 : RM-707_021.013_00.01_79.92_prd.rofs3.fpsx
CNT : RM-707_021.013_U01.01_79.92.uda.fpsx
Flashing phone now...
Check files done...
-> Check SW version...
FlashFile version : 021.013
Phone version : 021.013
-> Check SW version : Reflash
Backup CRT308 data...
CRT308 Backup Created
SL3 Simlock read ... ok
WMDRM read ... ok
Check communication with phone....
ADL req restart
Communication verify done... Preparing...
Gathering phone info...
Check communication with phone...
Batery valtage : 3669 mV
-> Batery voltage less, than 3,8V (3669mV). Continue at user risk
Reboot....
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00001040
EM1 ID: 00001030
PUBLIC ID: 1060021961F75840B3DADC4549CD0FAC9BF141EC
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.16.0
Processing RAWLOADER...
FLIC : 006000EC
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.16.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
IMEI : 35625704XXXXXXX
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Cert Read done!

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...
SimLock Data saved...
SimLock Key saved...
WMDRM_PD Data saved...

RPL saved : D:\GSM\BEST\Soft\InfinityBox_install_BEST_v1.23\Ba ckup\Cert\35625704XXXXXXX.rpl

===Flashing [MCU]===
Erase : Processing RM-707_021.013_79.92_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing RM-707_021.013_79.92_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 505 blocks
TIME : Write time : 00:00:17
MCU Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

===Flashing [PPM]===
Erase : Processing RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-707_021.013_04.01_Russian_79.92_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 196 blocks
TIME : Write time : 00:00:07
PPM Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

===Flashing [PPM2]===
Erase : Processing RM-707_021.013_00.01_79.92_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-707_021.013_00.01_79.92_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 2 blocks
TIME : Write time : 00:00:00
PPM Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

===Flashing [CNT]===
Erase : Processing RM-707_021.013_U01.01_79.92.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing RM-707_021.013_U01.01_79.92.uda.fpsx
Total writen 521 blocks
TIME : Write time : 00:00:22
CNT Write done
ADL: Request programm status
NAND status : 00000001 / 00000001 / 00000000

ADL: Close_Session
Content: 000300000000010000000100000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:51
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia X7-00
Software Info: V 92_11w15.4 17-05-11 RM-707 (c) Nokia
IMEI: 35625704XXXXXXX
Ape Version: 021.013
Product code: 059G558
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
Set phone to Normal mode...
AfterFlash operations done...
Done!

Elapsed: 00:01:48
Connect phone on selected interface...

:appl::appl::appl:

AABBCC

08.07.2011, 15:54

E61i RM-227, висел на белом экране. Пробовал прошить BEST v1.23 через UFS, закончилось неудачно. Лог подкрепляю. Потом прошил по F-Bus MT Box-ом и ТА заработал, хотя и ругнулся на распаковку контента. Лог тоже подкрепляю.
UFS S/N xxxxx boot - Ok

Connect phone on selected interface...

Core version : 1.23 , Rev : 4.8

Phone found!
Series 60 Device detected!
read info... - Ok

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm227_m128_h20_ks_prod_306336900_c00_combined.bin
PPM : rm227_m128_h20_ks_prod_306336900_v12_variant.bin
CNT : rm227_rm294_cp_3.0.fpsx
Check FlashFiles, Please, wait...
-> SWversion check skipped : Manual mode selected

Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : 41F2333967815F4FCC93CED9F3C39B3A509E8E2E
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 1A50020222EF6A50F952D867BBB8A6793E15D9B5
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 22E800EC , CMT , NOR
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLCNT : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent
CMT PAPUB : F6AB1F68D2E4D7D0487762E37D74EA7D923C341FBD
Transmission mode : Dual (Ddr, TX2)

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 02
FLASHID : 00780098 , APE ,
APE Flash ID : 00780098 < TOSHIBA => K5E1G12ACM
FLCNT : 01010000020000000600000000000000000000
Sending ALGO....
Use : h3_sam_nand_xsr.fg , Rev : 0.0 Ver : 1.47.0
APE Algo sent
APE PAPUB : F6AB1F68D2E4D7D0487762E37D74EA7D923C341FBC
Transmission mode : Dual (Ddr, TX2)

Boot Done!

Partitioning....
Partitioning Ok...
Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm227_m128_h20_ks_prod_306336900_c00_combined.bin
Found 3 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00000000 - 0x0052959D
CMT , NOR , Area : 0x006A0000 - 0x006DFFFF
CMT , NOR , Area : 0x00F00000 - 0x00FDFFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
Found 3 areas to erase, erase group
Asic : APE , Sub : NAND
APE , NAND , Area : 0x00000000 - 0x0007FFFF
APE , NAND , Area : 0x00080000 - 0x000803FF
APE , NAND , Area : 0x000C0000 - 0x03CFFFFF
Erasing, wait.....
APE : Group erase Ok
TIME : Erase time : 00:00:42
PrReq : NOR , 00
PrReq : NAND , 0103000068D2E400D0487700E37D74
Transmission mode : Dual (Ddr, TX2)
Write : Processing rm227_m128_h20_ks_prod_306336900_c00_combined.bin
CMT: Writing Hash CERT [NOLO]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [DSP0]
CMT: Writing Hash CERT [MCUSW]
CMT: Writing Hash CERT [ADL]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
APE: Writing Hash CERT [KEYS]
APE: Writing Hash CERT [X-LOADER]
APE: Writing Hash CERT [PRIMAPP]
APE: Writing Hash CERT [SOS+LOADER]
APE: Writing Hash CERT [ADL]
APE: Writing Hash CERT [SOS+XZIP]
APE: Writing Hash CERT [PASUBTOC]
APE: Writing Hash CERT [PAPUBKEYS]
APE: Writing Hash CERT [SOS*CORE]
APE: Writing Hash CERT [SOS+ROFS]
APE: Writing Hash CERT [SOS+ROFX]
Total writen 1499 blocks
TIME : Write time : 00:04:10

PrReq : NOR , 00
PrReq : NAND , 0103000068D2E400D0487700E37D74

Partitioning....
Partitioning Ok...
Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm227_m128_h20_ks_prod_306336900_v12_variant.bin
Found 1 areas to erase, erase group
Asic : APE , Sub : NAND
APE , NAND , Area : 0x02860000 - 0x03CFFFFF
Erasing, wait.....
APE : Group erase Ok
TIME : Erase time : 00:00:01
PrReq : NOR , 00
PrReq : NAND , 0103000068D2E400D0487700E37D74
Transmission mode : Dual (Ddr, TX2)
Write : Processing rm227_m128_h20_ks_prod_306336900_v12_variant.bin
APE: Writing Hash CERT [SOS+ROFX]
Total writen 1497 blocks
TIME : Write time : 00:01:38

PrReq : NOR , 00
PrReq : NAND , 0103000068D2E400D0487700E37D74

Transmission mode : Dual (Ddr, TX2)
Erase : Processing rm227_rm294_cp_3.0.fpsx
Erase : No any region, skip erase
TIME : Erase time : 00:00:00
PrReq : NOR , 00
PrReq : NAND , 0103000068D2E400D0487700E37D74
Transmission mode : Dual (Ddr, TX2)
Write : Processing rm227_rm294_cp_3.0.fpsx
Error write block at : 2
ERR : 000000000000000910000000
Error on Flashing Phone!
Error... :(

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Лог MT-BOX
Scanning files, please wait...
Done
Selected Highest installed version: 3.0633.69
Mcu rm227_m128_h20_ks_prod_306336900_c00_combined.bin
Ppm rm227_m128_h20_ks_prod_306336900_v12_variant.bin
Content rm227_rm294_cp_3.0.fpsx
Using Tx2 Data line.
BB5 PM back Phone is in: Phone is not responding!
Processing File: rm227_m128_h20_ks_prod_306336900_c00_combined.bin
Boot...
rap3gv3_2nd.fg
RAP3Gv3_algo.fg
helen3_2nd.fg
rap3gv3_2nd.fg
RAP3Gv3_algo.fg
helen3_2nd.fg
h3_sam_nand_xsr.fg
CMT Certificates
NPC 0x0200
HWC 0x0100
CCC 0x0200
APE Certificates
C:\Program Files\GriffinTeam\MT-Box\rpls\351879011604321.rpl
Erase RAP3 [00000000 - 0052959D]
Erase RAP3 [006A0000 - 006DFFFF]
Erase RAP3 [00F00000 - 00FDFFFF]
Erase APE [00000000 - 0007FFFF]
Erase APE [00080000 - 000803FF]
Erase APE [000C0000 - 03CFFFFF]
Erase[67.04 MB]...
Waiting response for 132 Sec...in 5.14s
Flash[40.98 MB]...in 68.02s
* * Processed file in 91.28 seconds
Processing File: rm227_rm294_cp_3.0.fpsx
Boot...
rap3gv3_2nd.fg
RAP3Gv3_algo.fg
helen3_2nd.fg
h3_sam_nand_xsr.fg
Erase[0.00 MB]...
in 0.06s
Flash[0.14 MB]...in 8.53s
* * Processed file in 33.69 seconds
Extract content...fail
Processing File: rm227_m128_h20_ks_prod_306336900_v12_variant.bin
Boot...
rap3gv3_2nd.fg
RAP3Gv3_algo.fg
helen3_2nd.fg
h3_sam_nand_xsr.fg
Erase APE [02860000 - 03CFFFFF]
Erase[20.63 MB]...
Waiting response for 132 Sec...in 1.91s
Flash[11.70 MB]...in 28.41s
* * Processed file in 38.33 seconds
* * * Phone flashing done in 4: 5 minutes
Post Flash serial tunning of phone....
Pooling mode for full factory set...
V 3.0615.3/31-01-08/RM-227 (c) Nokia.
IMEI: 351879011xxxxxx
Factory Default Settings...OK
Dynamic camera configuration...
Pooling mode for profile update...
RM-227\RM227_0543955_3.0633.69.00_001.dcpf\Refurbish\ rm227_default.xml
Sending Profile to Phone...OK

chabrus

08.07.2011, 16:25

Разблокировка 6210n RM-408 от Show

Phone found!
Series 60 Device detected!
read info... - Ok

Unlock procedure started...

Phone Imei: 356831021167315
Checking locks...
Conf key : 1000000000000000
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 1

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
=============================
LOCKS : Closed
=============================
PA_SL2 phone detected...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000010000022600010006400C192101031103
CMT EM0 ID : 00000296
CMT EM1 ID : 00000B22
CMT PUB ID : 0D80000700790052F60086D95C4D0340E5CF6BB0
CMT MODE ID : 00
CMT R_HASH : CAEEBB65D3C48E6DC73B49DC5063A2EE
CMT ROM ID : 4B9B75103E691FF8

CMT : Sending 2nd loader...
CMT Loader sent, Boot Ok
rap= 0D80000700790052F60086D95C4D0340E5CF6BB0
hash= CAEEBB65D3C48E6DC73B49DC5063A2EE
key= 97FE4F54AF71F3A90DB3CA6472A9C3ED2BE5AE00
Init Service mode... Wait...

Key file updated...
Using F-bus count...
Sending code 401166690849177 Level : 7 to SimLock Server...
Simlock Server Answer: Unlock code Accepted! :)
Done!
Правда по интерфейсу USB бест не захотел его отлачивать, пришлось цеплять через UFS. Было бы не плохо, если бы прикрутили поддержку анлока по USB.

JayDi

08.07.2011, 16:29

USB
1. RdKey
2. Опции становятся доступны....

renat_d

08.07.2011, 18:21

Вообще из-за МТР-драйвера может быть такое, но, тут зависит от того, что первым ставится - Phonet или МТР - если phonet - тел увидится сразу, при мтр - может быть до двух минут.

Подтверждаю ! - у меня раньше ( на старой винде ) ставился драйвер Phone_Generic первым а MTP последним :kos:
В последнее время при постфлешинге или бекапе rpl не жду пока установится MTP ( почему то первым ставится, гад ) - сразу же захожу в диспетчер оборудования и правой кнопкой по значку ?Phone? в автоматическом режиме устанавливаю драйвер:appl:
Диспетчер можно не закрывать - и оттуда потом удалить драйвер после рабочей сессии с телефоном .
Занимает 10-15 секунд - против 2 мин

BOSS®™

13.07.2011, 07:59

Работа с BEST версии 1.24
Успешно Восстановил SD Нокиа-6700 RM-470, через UFS все прошло с первого раза.

card found: S/N ?????????
registered to: BOSS

Connect phone on selected interface...

UFS S/N 75301 boot - Ok

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SDData Damaged!!!!! :(
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

Repair SD procedure started...

Phone Imei: ???????????????
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000030000022600010007600C192102011104
CMT EM0 ID : 00000C34
CMT EM1 ID : 00000C30
CMT PUB ID : 0C80000FD4600344DD3CC24BA77D3A45A3777A5B
CMT MODE ID : 00
CMT R_HASH : 25B977A055BE9B5DEC0C38A2A279C695
CMT ROM ID : 3E273BF637BE26FA

CMT : Sending 2nd loader...
Use : RAPUv11_2nd.fg
rap= 0C80000FD4600344DD3CC24BA77D3A45A3777A5B
hash= 25B977A055BE9B5DEC0C38A2A279C695
key= D5CA9B73BB4EC70F1319C37EF4AA3219EB79C896

Init Service mode... Wait...

Key file updated...
Check phone mode...
Phone in Local mode
Seting Test mode... wait...
Test mode set
Writing Super Dongle Key... Ok
Done!

Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

:appl::appl::appl::appl::appl::appl::appl:

SergDeParchi

13.07.2011, 12:26

Nokia 6600i-c1 RM-570 не включается, предыстория не известна
Версия 1.23:
Core version : 1.23 , Rev : 4.8

Selected FlashSettings : Cold Flash
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm570__36.60.mcusw
PPM : rm570__36.60.ppm_i
CNT : rm570__36.60_ISM_014.image_i_ru_black
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Getting product info...
Dead Mode is Selected
Waiting for USB device...
--- Press phone's power button or insert cable & charger! ---
Connection opened successfully
Waiting for communication response.
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006030C192101023000
CPU ID : RAP3Gv3 , Features : No any extended features
RAP_PUB: 2610010D4ACB8C5621FC14219C7013DC45A1EEC1
CMT_ROOT: 9DDBFCFE6E73CED7D8C6268C8EB85723
PatchRAWLoader: Patched OK
Processing RAWLOADER...
Processing UPDAPP...
Processing PASUBTOC...
TIME : Boot time : 00:00:06
Reopening the connection...
Waiting for response: 30
Wait for device bootup
-> Bootcode start in CMT fail ! Need flash via programming device :(
-> Error while flashing... :(

Phone disconected!
Версия 1.24:
Core version : 1.24 , Rev : 2.0

Selected FlashSettings : Cold Flash
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm570__36.60.mcusw
PPM : rm570__36.60.ppm_i
CNT : rm570__36.60_ISM_014.image_i_ru_black
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Getting product info...
Dead Mode is Selected
Waiting for USB device...
--- Press phone's power button or insert cable & charger! ---
Connection opened successfully
Waiting for communication response.
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006030C192101023000
CPU ID : RAP3Gv3 , Features : No any extended features
RAP_PUB: 2610010D4ACB8C5621FC14219C7013DC45A1EEC1
CMT_ROOT: 9DDBFCFE6E73CED7D8C6268C8EB85723
PatchRAWLoader: Patched OK
Processing RAWLOADER...
Processing UPDAPP...
Processing PASUBTOC...
TIME : Boot time : 00:00:06
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
Waiting for response: 28
ADL -> [2nd] changing...
ADL Server confirm flashmode!
ADL : Check data
ADL : Data accepted
ADL : ASIC CMT select Ok
===Flashing [MCU]===
Erase : Processing rm570__36.60.mcusw
Found 5 areas to erase
Erasing area 0x00000000 - 0x0001FFFF, NOR, CMT
Result: 0000
Erasing area 0x00040000 - 0x000BFFFF, NOR, CMT
Result: 0000
Erasing area 0x000C0000 - 0x0013FFFF, NOR, CMT
Result: 0000
Erasing area 0x01780000 - 0x0197FFFF, NOR, CMT
Result: 0000
Erasing area 0x00140000 - 0x0177FFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:01:44
Write : Processing rm570__36.60.mcusw
Total 116 [116/0/0] blocks to write, writing...
CMT : Writing Hash CERT [NOLO]
CMT : Writing Hash CERT [KEYS]
CMT : Writing Hash CERT [PRIMAPP]
CMT : Writing Hash CERT [PASUBTOC]
CMT : Writing Hash CERT [PAPUBKEYS]
CMT : Writing Hash CERT [UPDAPP]
CMT : Writing Hash CERT [DSP0]
CMT : Writing Hash CERT [MCUSW]
TIME : Write time : 00:02:22
MCU Write done
===Flashing [PPM]===
Erase : Processing rm570__36.60.ppm_i
Found 1 areas to erase
Erasing area 0x01980000 - 0x021BFFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:00:34
Write : Processing rm570__36.60.ppm_i
Total 28 [28/0/0] blocks to write, writing...
TIME : Write time : 00:00:43
PPM Write done
===Flashing [CNT]===
Erase : Processing rm570__36.60_ISM_014.image_i_ru_black
Found 2 areas to erase
Erasing area 0x02620000 - 0x03F9FFFF, NOR, CMT
Result: 0000
Erasing area 0x021C0000 - 0x0261FFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:02:04
Checking content info...
Check Image : Content size is 128k, use direct write mode
Write : Processing rm570__36.60_ISM_014.image_i_ru_black
Total 40 [40/0/0] blocks to write, writing...
TIME : Write time : 00:00:59
CNT Write done
ADL : End flashing

Flashing done!
Total flash time : 00:08:28
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia 6600i slide
Software Info: V 36.60 07-12-09 RM-570 (c) Nokia
IMEI: 355249037542853
PPM version : V 36.60 07-12-09 RM-570 (c) Nokia I
Product code: 0581891
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
AfterFlash operations done... Reconnect, wait...
Done!

Elapsed: 00:09:19

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok
:appl:

ivanych79

13.07.2011, 12:36

5800 разлок через усб

Phone found!
Series 60 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia 5800 XpressMusic
Software ver : V ICPR72_09w06.2 03-03-09 RM-356 (c) Nokia
IMEI : 354183023784495
Ape Ver : V 21.0.025
APE Var : V 21.0.025V 21.0.025 V 21.0.025
APE ADSP: 256
DSP Ver : tube_ICPR72_09w06_p1
APE Test: eno_version
PPM :
CNT :
Product SN : CCH911576
Product code : 0577181
Base Prd.code: 0552692
Module code :
Long Prod.SN : 0
Hardware info=======
HWID : 1101
Retu : 16
Tahvo : 22
Batery: 3899 mV
Camera:
CMT BT:
APE BT: HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12708.
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI : 354183023784495
IMEI spNet : 3A 45 81 03 32 87 44 09
IMEI svNet : 33 45 81 03 32 87 44 49 F1

Conf key : 8000000000000000
Provider key : 2320300000000000
Provider : T-Mobile ;Austria
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 2

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
BLK : 2
Lock1:Close
=============================
LOCKS : Closed
=============================
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Phone disconected!

Connect phone on selected interface...

Read Uniq key data started...

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101031103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
PUBLIC ID: 1930011940C90158DAD347F28437BD87F2E87B05
Fetching data, wait...

Reinsert cable and battery, press powerOn button again

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101031103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000296
EM1 ID: 00000B22
PUBLIC ID: 1930011940C90158DAD347F28437BD87F2E87B05
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: 4B9B75103E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.24.0
Processing RAWLOADER...
FLIC : 004000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.24.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:00
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : 76A20187051C30162EE91C77AE5E6011F5F1BA61

CFL: Close_Session
Content: 000300000000040000000400000000
CFL: Reboot

Wait, reconneting...

rap= 1930011940C90158DAD347F28437BD87F2E87B05
hash= CAEEBB65D3C48E6DC73B49DC5063A2EE
key= 8CA635C85D7A0775458D5373FA46BA3ED799399A

Key file updated...

Connect phone on selected interface...

Done!

Phone found!
Series 60 Device detected!
read info... - Ok

Unlock procedure started...

Phone Imei: 354183023784495
Checking locks...
Conf key : 8000000000000000
Provider key : 2320300000000000
Provider : T-Mobile ;Austria
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 2

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
BLK : 2
Lock1:Close
=============================
LOCKS : Closed
=============================
PA_SL2 phone detected...
Key file exists, no need to read...
Using F-bus count...
Sending code 889702243561972 Level : 7 to SimLock Server...
Simlock Server Answer: Unlock code Accepted! :)
Unlock Done!

Reading Phone Info....
Connected phone - Nokia 5800 XpressMusic
Software ver : V ICPR72_09w06.2 03-03-09 RM-356 (c) Nokia
IMEI : 354183023784495
Ape Ver : V 21.0.025
APE Var : V 21.0.025V 21.0.025 V 21.0.025
APE ADSP: 256
DSP Ver : tube_ICPR72_09w06_p1
APE Test: eno_version
PPM :
CNT :
Product SN : CCH911576
Product code : 0577181
Base Prd.code: 0552692
Module code :
Long Prod.SN : 0
Hardware info=======
HWID : 1101
Retu : 16
Tahvo : 22
Batery: 3860 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI : 354183023784495
IMEI spNet : 3A 45 81 03 32 87 44 09
IMEI svNet : 33 45 81 03 32 87 44 49 F1

Conf key : 8000000000000000
Provider key : 2320300000000000
Provider : T-Mobile ;Austria
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 2

LOCK STATUS :
=============================
BLK : 1
Lock1:Open
BLK : 2
Lock1:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

E75 разлок через усб
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101031103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
PUBLIC ID: 1EA00010097B0052C9E5ABF72B5D276AC4DCBB6C
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
Fetching data, wait...

Reinsert cable and battery, press powerOn button again

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101031103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 1EA00010097B0052C9E5ABF72B5D276AC4DCBB6C
ASIC MODE ID: 00
ROOT KEY HASH: CAEEBB65D3C48E6DC73B49DC5063A2EE
ROM ID: 4B9B75103E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.24.0
Processing RAWLOADER...
FLIC : 004000EC
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.24.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:00
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : C29DF97EC55AABC28ACB9029D2E577CA237E7179

CFL: Close_Session
Content: 000300000000020000000200000000
CFL: Reboot

Wait, reconneting...

rap= 1EA00010097B0052C9E5ABF72B5D276AC4DCBB6C
hash= CAEEBB65D3C48E6DC73B49DC5063A2EE
key= 822C9BA5A6CCF04F1BB0FC3B41FBE67C8A8DD428

Key file updated...

Connect phone on selected interface...

Done!

Phone found!
Series 60 Device detected!
read info... - Ok

Unlock procedure started...

Phone Imei: 359557014218677
Checking locks...
Conf key : 0000000000000000
Provider key : 2320100000000000
Provider : Mobilkom Austria ;Austria
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 2

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
BLK : 2
Lock1:Close
=============================
LOCKS : Closed
=============================
PA_SL2 phone detected...
Key file exists, no need to read...
Using F-bus count...
Sending code 079754787157964 Level : 7 to SimLock Server...
Simlock Server Answer: Unlock code Accepted! :)
Unlock Done!

Reading Phone Info....
Connected phone - Nokia E75
Software ver : V ICPR72_09w09.2 27-05-09 RM-412 (c) Nokia
IMEI : 359557014218677
Ape Ver : 110.48.125
APE Var : 110.48.125_rofs2110.48.125.248.08_rofs3
APE ADSP: 256
DSP Ver : ICPR72_09w09
APE Test: RM412ENOx2008wk50v0.017
PPM :
CNT : 110.48.125
Product SN : STD098875
Product code : 0581515
Base Prd.code: 0558819
Module code :
Long Prod.SN : 0
Hardware info=======
HWID : 0600
Retu : 15
Tahvo : 22
Batery: 3658 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI : 359557014218677
IMEI spNet : 3A 95 55 07 41 12 68 07
IMEI svNet : 33 95 55 07 41 12 68 07 F4

Conf key : 0000000000000000
Provider key : 2320100000000000
Provider : Mobilkom Austria ;Austria
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 2

LOCK STATUS :
=============================
BLK : 1
Lock1:Open
BLK : 2
Lock1:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

ildar

14.07.2011, 08:25

5800 rm-356 SL3 ROOT KEY HASH: 479C6DDE3942E12C429C1D6ADED80371
восстановление с заводского RPL по USB не кого го F-BUS-а и коробок

-> Cert Earse can be done only in DEAD mode, Check DEAD mode, and connect powered OFF phone

Phone disconected!

Connect phone on selected interface...

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101051103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000296
EM1 ID: 00000B22
PUBLIC ID: 1970010C6DAF0052E510B83506E548940470CFE9
ASIC MODE ID: 00
ROOT KEY HASH: 479C6DDE3942E12C429C1D6ADED80371
ROM ID: 4B9B75103E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.24.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.24.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:00
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : 76A20187051C30162EE91C77AE5E6011F5F1BA61

ADL: Preparing for erase certificates...

Erase NPC... Ok
Erase CCC... Ok
Erase HWC... Ok

ADL: Writing Flash certs done! :)

CFL: Close_Session
Content: 000300000000000000000000000000
CFL: Reboot
Connect phone on selected interface...

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
SimLock Data found!
SimLock key found!
SuperDongle Key found!
CMLA key found!
WMDRM key found!
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000010000022600010006400C192101051103
CPU ID : RAPIDOv11 , Features : Dead-Test, USBRPL, WR/ER-USB
EM0 ID: 00000296
EM1 ID: 00000B22
PUBLIC ID: 1970010C6DAF0052E510B83506E548940470CFE9
ASIC MODE ID: 00
ROOT KEY HASH: 479C6DDE3942E12C429C1D6ADED80371
ROM ID: 4B9B75103E691FF8
Use URAPIDOv11_2nd.fg , Rev : 2.0 Ver : 11.24.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.5
Use URAPIDOv11_XSR15_alg.fg , Rev : 2.0 Ver : 11.24.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:00
Reopening the connection...
CFL: Wait for Loader take control ...
CFL: Check mode
Phone ready, boot Ok
TransReq set Ok
PAPUBkeys : 76A20187051C30162EE91C77AE5E6011F5F1BA61

ADL: Preparing for write certificates...

Erase NPC... Ok
Writing NPC... Ok
Erase CCC... Ok
Writing CCC... Ok
Erase HWC... Ok
Writing HWC... Ok

ADL: Writing Flash certs done! :)

CFL: Close_Session
Content: 000300000000000000000000000000
CFL: Reboot
Wait, reconneting...
Check phone mode...
Phone in Local mode
Seting Test mode... wait...
Test mode set
Failed init Test mode... :(

Phone disconected!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock Damaged!!!!! :(
Security status : Security Damaged!!!!! :(
-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
SimLock Data found!
SimLock key found!
SuperDongle Key found!
CMLA key found!
WMDRM key found!
-> Skip Flash keys Part, for Flash Part use Dead Mode or Fbus
Check phone mode...
Phone already in Test mode, skip change...

Writing SimLock Key... Ok!
Writing SimLock Data... Ok!

SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!! :(

Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!! :(
-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

Processing Server SX4 Auth
Checking SDD key...
Check SD : Key is Ok
Operating mode is OK, no need change...
Connecting to server...
Connect to server Ok, checking
SX4 Server : Online, ver:1.04 , Infinity Team (c) 2011
SX4, processing Step #1
SX4, processing Step #2
SX4, processing Step #3
SX4 Result : Ok

Upload PM checked
Uploading RF/Battery tune to phone...
Using : RM-356.pm
Operating mode is OK, no need change...

Field 1
Record 0 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 6 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 16 write - Ok
Record 18 write - Ok
Record 20 write - Ok
Record 22 write - Ok
Record 23 write - Ok
Record 24 write - Ok
Record 25 write - Ok
Record 26 write - Ok
Record 28 write - Ok
Record 29 write - Ok
Record 31 write - Ok
Record 33 write - Ok
Record 34 write - Ok
Record 35 write - Ok
Record 37 write - Ok
Record 39 write - Ok
Record 44 write - Ok
Record 45 write - Ok
Field 309
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 17 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => OK

Done!

Elapsed: 00:00:01

Upload done

Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

B.E.S.T. of the Best :appl:

Shmastik

14.07.2011, 11:17

Unlock 7510a-b

Reading Phone Info....
Connected phone - Nokia 7510a-b
Software ver : V 03.60 18-11-08 RM-399 (c) Nokia
IMEI : 359321021820730
Ape Ver :
APE Var :
APE ADSP:
DSP Ver : ICPR81_08w37
APE Test:
PPM : V 03.60 18-11-08 RM-399 (c) Nokia NTM
CNT : Content: User Content Package tmobusa_v1 26-Nov-08 V 03.60 18-11-08 RM-399 (c) Nokia
Product SN : DVE888656
Product code : 0568567
Base Prd.code: 0556065
Module code : 0203794
Long Prod.SN : 0
Hardware info=======
HWID : 1503
Retu : 15
Tahvo : 22
Batery: 3962 mV
Camera:
CMT BT: 410B-v74
APE BT:
APE HW:
LCDVer: SEIKO
RF ic :
Lock info ===========
IMEI : 359321021820730
IMEI spNet : 3A 95 23 01 12 28 70 03
IMEI svNet : 33 95 23 01 12 28 70 03 F5

Conf key : 8000000000000000
Provider key : 3102000000000000
Provider : T-Mobile;U.S.A.
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 14

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
BLK : 2
Lock1:Close
BLK : 3
Lock1:Close
BLK : 4
Lock1:Close
BLK : 5
Lock1:Close
BLK : 6
Lock1:Close
BLK : 7
Lock1:Close
BLK : 8
Lock1:Close
BLK : 9
Lock1:Close
BLK : 10
Lock1:Close
BLK : 11
Lock1:Close
BLK : 12
Lock1:Close
BLK : 13
Lock1:Close
BLK : 14
Lock1:Close
=============================
LOCKS : Closed
=============================
CRT308 Backup Created

User Code : not set
MMC pwd : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Connect phone on selected interface...

UFS S/N %%%%% boot - Ok

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Unlock procedure started...

Phone Imei: 359321021820730
Checking locks...
Conf key : 8000000000000000
Provider key : 3102000000000000
Provider : T-Mobile;U.S.A.
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 14

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
BLK : 2
Lock1:Close
BLK : 3
Lock1:Close
BLK : 4
Lock1:Close
BLK : 5
Lock1:Close
BLK : 6
Lock1:Close
BLK : 7
Lock1:Close
BLK : 8
Lock1:Close
BLK : 9
Lock1:Close
BLK : 10
Lock1:Close
BLK : 11
Lock1:Close
BLK : 12
Lock1:Close
BLK : 13
Lock1:Close
BLK : 14
Lock1:Close
=============================
LOCKS : Closed
=============================
PA_SL2 phone detected...
Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000010000022600010006030C192101033000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 0EB0011496607D561C4DE2B67F73DAE61A0BCFA3
CMT MODE ID : 00
CMT R_HASH : 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
CMT Loader sent, Boot Ok
rap= 0EB0011496607D561C4DE2B67F73DAE61A0BCFA3
hash= 9DDBFCFE6E73CED7D8C6268C8EB85723
key= A598D3527BA2A64C4A06C1836599DAA86FFA23F9

Init Service mode... Wait...

Key file updated...
Using F-bus count...
Sending code 766875494947240 Level : 7 to SimLock Server...
Simlock Server Answer: Unlock code Accepted! :)
Unlock Done!

Reading Phone Info....
Connected phone - Nokia 7510a-b
Software ver : V 03.60 18-11-08 RM-399 (c) Nokia
IMEI : 359321021820730
Ape Ver :
APE Var :
APE ADSP:
DSP Ver : ICPR81_08w37
APE Test:
PPM : V 03.60
18-11-08
RM-399
(c) Nokia
NTM
CNT : Content: User Content Package tmobusa_v1 26-Nov-08
V 03.60
18-11-08
RM-399
(c) Nokia

Product SN : DVE888656
Product code : 0568567
Base Prd.code: 0556065
Module code : 0203794
Long Prod.SN : 0
Hardware info=======
HWID : 1503
Retu : 15
Tahvo : 22
Batery: 4081 mV
Camera:
CMT BT: Error
APE BT: Error
APE HW: Error
LCDVer: SEIKO
RF ic : 0800
Lock info ===========
IMEI : 359321021820730
IMEI spNet :
IMEI svNet :

Conf key : 8000000000000000
Provider key : 3102000000000000
Provider : T-Mobile;U.S.A.
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 14

LOCK STATUS :
=============================
BLK : 1
Lock1:Open
BLK : 2
Lock1:Open
BLK : 3
Lock1:Open
BLK : 4
Lock1:Open
BLK : 5
Lock1:Open
BLK : 6
Lock1:Open
BLK : 7
Lock1:Open
BLK : 8
Lock1:Open
BLK : 9
Lock1:Open
BLK : 10
Lock1:Open
BLK : 11
Lock1:Open
BLK : 12
Lock1:Open
BLK : 13
Lock1:Open
BLK : 14
Lock1:Open
=============================
LOCKS : All Open
=============================
User Code : not set
MMC pwd : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

:appl:

JayDi

15.07.2011, 07:57

X1-00 , прошивка
Connect phone on selected interface...

Core version : 1.24 , Rev : 2.0

Selected FlashSettings :
Files Set for Flashing :
MCU : rm732_004.550
PPM : rm732_004.55ei
CNT : rm7320_nai04.55ei

Infineon flashing...
Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
PBL : Dynamic
Boot Ok , 01AB
SBL : Dynamic
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG ...
FLASH ID : 0020000000048800
FLASH ID : UNKNOW [Not In Base]
Boot Done!

===Flashing [MCU]===
File : rm732_004.550
Image : hw_s02_rm732_r04.550.fls
Cert block found, sending....
Cert sent
Found 3 region(s)
Processing Region 1/3
Erase , Start : 0x00000000 , Len : 0x00020000
Erasing, wait ...
Erase done
Write , Start : 0x00000000 , Len : 0x00006000
Flashing , wait ...
Region flash done
Processing Region 2/3
Erase , Start : 0x00800000 , Len : 0x00400000
Erasing, wait ...
Erase done
Write , Start : 0x00800000 , Len : 0x003F0000
Flashing , wait ...
Region flash done
Processing Region 3/3
Erase , Start : 0x00C5D000 , Len : 0x00203000
Erasing, wait ...
Erase done
Write , Start : 0x00C5D000 , Len : 0x0019E700
Flashing , wait ...
Region flash done
Check : 722A
===Flashing [PPM]===
File : rm732_004.55ei
Image : hw_s02_rm732_004.55ei.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00100000 , Len : 0x00700000
Erasing, wait ...
Erase done
Write , Start : 0x00100000 , Len : 0x0053BAC0
Flashing , wait ...
Region flash done
Check : 820E
===Flashing [CNT]===
File : rm7320_nai04.55ei
Image : hw_s02_rm7320_nai04.55ei.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00E60000 , Len : 0x00100000
Erasing, wait ...
Erase done
Write , Start : 0x00E60000 , Len : 0x00081940
Flashing , wait ...
Region flash done
Check : 0400

Flashing done, rebooting...
-> Infineon info : Do FullFactory Sets after flashing
Flashing Done!

Init Service mode... Wait...

Afterflash settings...
SW ver : V 04.55
14-04-11
RM-732
(c) Nokia
IMEI : xxxxxxxxxxx
PCode :
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
All done!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Огромное спасибо комраду Kihmet за предоставленный телефон для тестов!
Буду пробовать издеваться над убитым IMEI в XG110.

[B]З.Ы. прошивка последних XG110 - отлично работает с версии 1.24

BRADJGA

15.07.2011, 12:11

3000 SMS сообщений в Nokia 6300 , начал тупить :)

Phone found!
Series 40 Device detected!
read info... - Ok

BackUp UserData : [SMS/MMS]
Selected package method...
Read Package : [SMS Package]
Generation mode : [S40]
Saved to : C:\InfinityBox\BEST\RM-217 Nokia 6300_3598120хххххх.smspkg
Read Done !

Elapsed: 00:09:38

Бекапы не делались родным софтом висло всё , Best справился .

komayo

15.07.2011, 16:09

отличии от MX- KEY-я хороший результат:
телефон С5-03 RM -697
card found: S/N *******
registered to: komayo

Connect phone on selected interface...

Core version : 1.24 , Rev : 2.0

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : RM-697_20.0.024_prd.core.C00
PPM : RM-697_20.0.024_prd.rofs2.V05
PPM2 : RM-697_20.0.024_C01_prd.rofs3.fpsx
CNT : RM697_011_U001.uda.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BB5 FLASH]: Bootrom Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 2680011928E25840AC39B63E904C2343DEA6D8BF
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.24.0
Processing RAWLOADER...
FLIC : 004000EC
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.24.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
IMEI : 35742*******
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Cert Read done!

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : c:\InfinityBox\BEST\Backup\Cert\357425********_CRT .rpl

===Flashing [MCU]===
Erase : Processing RM-697_20.0.024_prd.core.C00
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing RM-697_20.0.024_prd.core.C00
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 443 blocks
TIME : Write time : 00:00:18
MCU Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [PPM]===
Erase : Processing RM-697_20.0.024_prd.rofs2.V05
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-697_20.0.024_prd.rofs2.V05
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 114 blocks
TIME : Write time : 00:00:05
PPM Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [PPM2]===
Erase : Processing RM-697_20.0.024_C01_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM-697_20.0.024_C01_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 2 blocks
TIME : Write time : 00:00:00
PPM Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [CNT]===
Erase : Processing RM697_011_U001.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM697_011_U001.uda.fpsx
Total writen 55 blocks
TIME : Write time : 00:00:02
CNT Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:28
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia C5-03
Software Info: V ICPR82_11w16 20-04-11 RM-697 (c) Nokia
IMEI: 357425041831437
Ape Version: V 20.0.024
Product code: 059C520
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
AfterFlash operations done... Reconnect, wait...
Done!

Elapsed: 00:00:51
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Браво респект проекту еще раз :appl:

NeOnyx

15.07.2011, 23:14

Прошу добавить в следующем релизе PM под RM-615, пришлось "резать" самому, ниже прилагаю, восстанавливал ST_Security, BEST справился как всегда))

Phone found!
Series 40 Device detected!
read info... - Ok

Processing Server SX4 Auth
Checking SDD key...
Check SD : Key is Ok
Operating mode is OK, no need change...
Connecting to server...
Connect to server Ok, checking
SX4 Server : Online, ver:1.04 , Infinity Team (c) 2011
SX4, processing Step #1
SX4, processing Step #2
SX4, processing Step #3
SX4 Result : Ok

Upload PM checked
Uploading RF/Battery tune to phone...
RM-615.pm not exist
Select file, please
Using : RM-615.pm
Operating mode is OK, no need change...

Field 1
Record 0 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 6 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 16 write - Ok
Record 18 write - Ok
Record 20 write - Ok
Record 22 write - Ok
Record 23 write - Ok
Record 24 write - Ok
Record 25 write - Ok
Record 26 write - Ok
Record 28 write - Ok
Record 29 write - Ok
Record 31 write - Ok
Record 33 write - Ok
Record 34 write - Ok
Record 35 write - Ok
Record 37 write - Ok
Record 39 write - Ok
Record 40 write - Ok
Record 41 write - Ok
Record 42 write - Ok
Record 43 write - Ok
Record 44 write - Ok
Record 45 write - Ok
Field 309
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 7 write - Ok
Record 17 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => OK

Done!

Elapsed: 00:00:04

Upload done

Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

Shmastik

16.07.2011, 12:47

Попался клиент с Nokia 6700c с просьбой вычитать телефонную книгу. В телефоне не исправен клавиатурный модуль, соответственно по USB зацепить телефон не удалось. Телефон цеплял через JAF и UFS при считывании книги показывал разное количество контактов (через UFS прочитал максимум 34 контакта) и с минуты 2 ее вычитывал, иногда зависая с выкидыванием окошка с ошибкой.

Инфо телефона
Phone found!
Series 40 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia 6700 classic
Software ver : V 13.10 16-06-10 RM-470 (c) Nokia
IMEI : 353790043547362
Ape Ver :
APE Var :
APE ADSP:
DSP Ver : ICPR81_10w09
APE Test:
PPM : V 13.10
16-06-10
RM-470
(c) Nokia
I
CNT : Content: i_ua_chrome
V 13.10
16-06-10
RM-470
(c) Nokia
Product SN : KML329843
Product code : 0571173
Base Prd.code: 0590482
Module code : 0204199
Long Prod.SN : 0
Hardware info=======
HWID : 1010
Retu : 34
Tahvo : 00
Batery: 4324 mV
Camera:
CMT BT: 410B-v190
APE BT:
APE HW:
LCDVer: TPO
RF ic : |Vapaus_5.1 | Aura_?.?
Lock info ===========
IMEI : 353790043547362
IMEI spNet :
IMEI svNet :

Conf key : 8000000000000002
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
User Code : 12345
MMC pwd : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Куски вариантов вычитки книги
BackUp UserData : [PhoneBook]
Generation mode : [S40]
Will read 34 blocks...
Error while reading...
Using search engine...
Data proceed ok...
csv file save to C:\InfinityBox\BEST\RM-470 Nokia 6700 classic_353790043547362.csv
59 phonebook records are found!
VCF Records saved to : BEST\Phones_Data\IMEI\
File saved to : C:\InfinityBox\BEST\RM-470 Nokia 6700 classic_353790043547362.S4pb
Read done ;)
Done...

BackUp UserData : [PhoneBook]
Generation mode : [S40]
Will read 34 blocks...
Error while reading...
Using search engine...
Data proceed ok...
csv file save to C:\InfinityBox\BEST\temp\RM-470 Nokia 6700 classic_353790043547362.csv
118 phonebook records are found!
VCF Records saved to : BEST\Phones_Data\IMEI\
File saved to : C:\InfinityBox\BEST\temp\RM-470 Nokia 6700 classic_353790043547362.S4pb
Read done ;)
Done...

BackUp UserData : [PhoneBook]
Generation mode : [S40]
Will read 34 blocks...
Error while reading...
Using search engine...
Data proceed ok...
csv file save to C:\InfinityBox\BEST\temp\RM-470 Nokia 6700 classic_353790043547362.csv
6 phonebook records are found!
VCF Records saved to : BEST\Phones_Data\IMEI\
File saved to : C:\InfinityBox\BEST\temp\RM-470 Nokia 6700 classic_353790043547362.S4pb
Read done ;)
Done...

JayDi

16.07.2011, 19:18

X1-01 прошивка версией 1.24
Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Reading Phone Info....
SW ver : V 05.28 02-06-11 RM-713 (c) Nokia
IMEI : 357890049642609
PPM : V 05.28
02-06-11
RM-713
(c) Nokia
IC
PCode : 059G439
BPCode : 059K2L3
HWID : 3051
LCDVer : WIN:BARACOAv80
NT39121
IMEI : 357890049642609
Sl Conf : 001-01-00000000000
Sl Prof : 000000000003000-2
Sl Aux : 000B0000
Hw Sig : 5CCA9C21B1ECBEC9
Provider : Default Test Operator

Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;

Done!

Core version : 1.24 , Rev : 2.0

Selected FlashSettings :
Files Set for Flashing :
MCU : rm713_005.290
PPM : rm713_005.29ij
CNT : rm7130_nai05.29ij

Infineon flashing...
Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
PBL : Dynamic
Boot Ok , 01AB
SBL : Dynamic
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000048800
FLASH ID : UNKNOW [Not In Base]
Boot Done!

===Flashing [MCU]===
File : rm713_005.290
Image : hw_b1_rm713_r05.290.fls
Cert block found, sending....
Cert sent
Found 3 region(s)
Processing Region 1/3
Erase , Start : 0x00000000 , Len : 0x00020000
Erasing, wait ...
Erase done
Write , Start : 0x00000000 , Len : 0x00006000
Flashing , wait ...
Region flash done
Processing Region 2/3
Erase , Start : 0x00800000 , Len : 0x00400000
Erasing, wait ...
Erase done
Write , Start : 0x00800000 , Len : 0x003F0000
Flashing , wait ...
Region flash done
Processing Region 3/3
Erase , Start : 0x00C5D000 , Len : 0x00203000
Erasing, wait ...
Erase done
Write , Start : 0x00C5D000 , Len : 0x0019E700
Flashing , wait ...
Region flash done
Check : F194
===Flashing [PPM]===
File : rm713_005.29ij
Image : hw_b1_rm713_005.29ij.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00100000 , Len : 0x00700000
Erasing, wait ...
Erase done
Write , Start : 0x00100000 , Len : 0x004C6F80
Flashing , wait ...
Region flash done
Check : 8D7E
===Flashing [CNT]===
File : rm7130_nai05.29ij
Image : hw_b1_rm7130_nai05.29ij.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00E60000 , Len : 0x00100000
Erasing, wait ...
Erase done
Write , Start : 0x00E60000 , Len : 0x000B0580
Flashing , wait ...
Region flash done
Check : 7E52

Flashing done, rebooting...
-> Infineon info : Do FullFactory Sets after flashing
Flashing Done!

Phone disconected!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Reading Phone Info....
SW ver : V 05.29 10-06-11 RM-713 (c) Nokia
IMEI : 357890049642609
PPM : V 05.29
10-06-11
RM-713
(c) Nokia
IJ
PCode : 059G439
BPCode : 059K2L3
HWID : 3051
LCDVer : WIN:BARACOAv80
NT39121
IMEI : 357890049642609
Sl Conf : 001-01-00000000000
Sl Prof : 000000000003000-2
Sl Aux : 000B0000
Hw Sig : 5CCA9C21B1ECBEC9
Provider : Default Test Operator

Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;

Done!

Phone disconected!

Shmastik, телефон почему-то отваливается - SW/HW - или коннект-проблемы. читать пок ане прочтет максимум. Обычно 3-5 попыток дают результат. Постараюсь добавить показ CNT сервера в FBUS чтоб не читать в слепую.

ildar

19.07.2011, 10:45

Почему BEST по USB не определяет ключи, в special.log-е есть
проверил на двух компьютерах и на двух ТА 6700 rm-470

[356049030522392]
rap=19B000158860034428F484359816F67166AA9EF9
hash=25B977A055BE9B5DEC0C38A2A279C695
key=F3C3A6F332BDAC133FE8A8B9CB6CFDCB766B141F

Reading Phone Info....
Connected phone - Nokia 6700c
Software ver : V 13.21 12-01-11 RM-470 (c) Nokia
IMEI : 356049030522392
Ape Ver :
APE Var :
APE ADSP:
DSP Ver : ICPR81_10w09
APE Test:
PPM : V 13.10 16-06-10 RM-470 (c) Nokia I
CNT : Content: ctv DE V 13.21 12-01-11 RM-470 (c) Nokia
Product SN : CV0069655
Product code : 0587899
Base Prd.code: 0590482
Module code :
Long Prod.SN : 0
Hardware info=======
HWID : 2001
Retu : 34
Tahvo : 00
Batery: 4052 mV
Camera:
CMT BT: 410B-v190
APE BT:
APE HW:
LCDVer: SHARP
RF ic :
Lock info ===========
IMEI : 356049030522392
IMEI spNet : 3A 65 40 09 03 25 32 09
IMEI svNet : 33 65 40 09 03 25 32 49 F9

Conf key : 8000000000000002
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

User Code : 12345
MMC pwd : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Checking StartUp data ...
-----------------------
SDD Key status : SDData Damaged!!!!! :(
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

Processing Server SX4 Auth
Checking SDD key...
Check SD : Key Damaged!!!
SX4 Auth error :(

Shmastik

20.07.2011, 14:43

Почему при подключении через Jaf не активны кнопочки Repair SDD, Repair SL, Local SX4 Auth и Repair PP? Тогда как при подключении через UFS кнопки активны. Замечено на N73 и 6233.

boris_ogor

20.07.2011, 14:56

Сначала нужно нажать кнопочку RD Key, после этого активизируются остальные.

Shmastik

20.07.2011, 16:19

Сначала нужно нажать кнопочку RD Key, после этого активизируются остальные.

Это конечно хорошо отвечено, но они не октивны и после Read key.

JayDi

20.07.2011, 16:27

Для того, чтоб стали активны - надо чтоб RdKey прошел успешно.

Shmastik

20.07.2011, 22:34

Для того, чтоб стали активны - надо чтоб RdKey прошел успешно.

RdKey проходит нормально и с UFS и с JAF. Притом просто подключаю JAF кнопки не активны, тут-же подключаю UFS кнопки становятся активны и наоборот.

Насколько я понимаю чтение ключей проводится единожды, а в дальнейшем берется просто с диска, поправьте если я не прав.

JayDi

20.07.2011, 22:55

Да, один раз для телефона. После уже не нужно его читать снова.

Shmastik

21.07.2011, 10:30

Да, один раз для телефона. После уже не нужно его читать снова.

RdKey проходит нормально и с UFS и с JAF. Притом просто подключаю JAF кнопки не активны, тут-же подключаю UFS кнопки становятся активны и наоборот.

Такое происходит только у меня или у кого-то тоже есть такие проблемы?

JayDi

21.07.2011, 11:03

Да, заметили фигню странную. Работает нормлаьно только для новых RAPIDO. С остальными проблемы возникли.

ildar

21.07.2011, 11:09

5220 RM-411 пришел с проблемой "не достаточно памяти". Прошил по USB проблема осталось
Phone found!
Series 40 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia 5220 XpressMusic
Software ver : V 07.23 17-07-09 RM-411 (c) Nokia
IMEI : 356840027462067
Ape Ver :
APE Var :
APE ADSP:
DSP Ver : ICPR72_09w17
APE Test:
PPM : V 07.23 17-07-09 RM-411 (c) Nokia I
CNT :
Product SN : KMH850707
Product code : 0563601
Base Prd.code: 0554881
Module code : 0203661
Long Prod.SN : 0
Hardware info=======
HWID : 7001
Retu : 15
Tahvo : 22
Batery: 3892 mV
Camera:
CMT BT: 2222-143C
APE BT:
APE HW:
LCDVer: SHARP
RF ic :
Lock info ===========
IMEI : 356840027462067
IMEI spNet : 3A 65 48 00 72 64 02 06
IMEI svNet : 33 65 48 00 72 64 02 46 F0

Conf key : 0000000000000000
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

User Code : 12345
MMC pwd : no any record found
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL2 phone detected

Done!

Core version : 1.24 , Rev : 2.0

Selected FlashSettings : FullFlash
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm411__07.23.mcusw
PPM : rm411__07.23.ppm_ci
PPM2 : rm411__07.23.ppm_ci
Flashing phone now...
Check files done...
-> SWversion check skipped : Manual mode selected
Backup CRT308 data...
CRT308 Backup Created
SLx Simlock Data read ... ok
SL2 Simlock read ... ok
WMDRM read ... ok
SimLock Data saved...
SimLock Key saved...
WMDRM_PD Data saved...

RPL saved : D:\BEST dongle\Backup\Cert\356840027462067_SIM.rpl

Getting product info...
RAP_BOOT: 0803000302010000
RAP_PUBLIC: 15B0000649E97D56DF663721B53FE182B1E9274B
CMT_ROOTKEY: 9DDBFCFE6E73CED7D8C6268C8EB85723
RAP_PAPUBKEY: D93826B23E9B093BE4DD7304FBAA6778996AE60B
Loader len: 307008, CHK: C0CE
ADL -> Sending loader...
Update Server code succesfully sent to phone!
TIME : Boot time : 00:00:04
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL -> [2nd] changing...
ADL Server confirm flashmode!
ADL : Check data
ADL : Data accepted
ADL : ASIC CMT select Ok
===Flashing [MCU]===
Erase : Processing rm411__07.23.mcusw
Found 6 areas to erase
Erasing area 0x00000000 - 0x000006BF, NOR, CMT
Result: 0000
Erasing area 0x000006C0 - 0x0001FFFF, NOR, CMT
Result: 0000
Erasing area 0x00040000 - 0x000BFFFF, NOR, CMT
Result: 0000
Erasing area 0x000C0000 - 0x0013FFFF, NOR, CMT
Result: 0000
Erasing area 0x00140000 - 0x0137FFFF, NOR, CMT
Result: 0000
Erasing area 0x01380000 - 0x0151FFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:02:17
Write : Processing rm411__07.23.mcusw
Total 1289 [1289/0/0] blocks to write, writing...
CMT : Writing Hash CERT [NOLO]
CMT : Writing Hash CERT [KEYS]
CMT : Writing Hash CERT [PRIMAPP]
CMT : Writing Hash CERT [PASUBTOC]
CMT : Writing Hash CERT [PAPUBKEYS]
CMT : Writing Hash CERT [UPDAPP]
CMT : Writing Hash CERT [DSP0]
CMT : Writing Hash CERT [MCUSW]
TIME : Write time : 00:01:05
MCU Write done
===Flashing [PPM]===
Erase : Processing rm411__07.23.ppm_ci
Found 1 areas to erase
Erasing area 0x01520000 - 0x01DBFFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:00:58
Write : Processing rm411__07.23.ppm_ci
Total 435 [435/0/0] blocks to write, writing...
TIME : Write time : 00:00:22
PPM Write done
===Flashing [PPM2]===
Erase : Processing rm411__07.23.ppm_ci
Found 1 areas to erase
Erasing area 0x01520000 - 0x01DBFFFF, NOR, CMT
Result: 0000
TIME : Erase time : 00:01:00
Write : Processing rm411__07.23.ppm_ci
Total 435 [435/0/0] blocks to write, writing...
TIME : Write time : 00:00:22
PPM Write done
ADL : End flashing

Flashing done!
Total flash time : 00:06:06
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia 5220 XpressMusic
Software Info: V 07.23 17-07-09 RM-411 (c) Nokia
IMEI: 356840027462067
PPM version : V 07.23 17-07-09 RM-411 (c) Nokia CI
Product code: 0563601
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
Set phone to Normal mode...
AfterFlash operations done...
Done!

Elapsed: 00:06:41

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Phone disconected!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok

Format File System...
Check phone mode...
Phone in Normal mode
Seting Local mode... wait...
Local mode set
Scanning FS parametres...
Checking Data...
Detected : 1 drive(s)...
Start formating....
Using Series 40 format algorithm...
==================================
Formating drive : C now...
Step1 : OK
Step2 : OK
End format...
==================================
Info : Reflash CNT only for repair content and user certificates
Done!

Format File System...
Operating mode is OK, no need change...
Scanning FS parametres...
Checking Data...
Detected : 1 drive(s)...
Start formating....
Using Series 40 format algorithm...
==================================
Formating drive : C now...
Step1 : OK
Step2 : OK
End format...
==================================
Info : Reflash CNT only for repair content and user certificates
Done!

Set phone in Normal mode...
Restarting...
Done!

Phone disconected!

Прошил по F-Bus-у через ATF (клиент спешил), все нормализовалось.

Turboxxx

21.07.2011, 11:36

JayDi

21.07.2011, 11:57

А проблема лишь в том, что CNT файл выбран на месте PPM2.

ildar

21.07.2011, 13:30

А проблема лишь в том, что CNT файл выбран на месте .

Да там не только на месте PPM2, так вообще CNT не выбран. Спешил.
===Flashing [PPM]===
Erase : Processing rm411__07.23.ppm_ci
Found 1 areas to erase
E.ppm_ci
Total 435 [435/0/0] blocks to write, writing...
TIME : Write time : 00:00:22
PPM Write done
===Flashing [PPM2]===
Erase : Processing rm411__07.23.ppm_ci
Found 1 areas to erase
Erasing area 0x01520000 - 0x01DBFFFF, NOR, CMT
Result: 0000:rofl:

Shmastik

21.07.2011, 14:06

Да, заметили фигню странную. Работает нормлаьно только для новых RAPIDO. С остальными проблемы возникли.

Я не пытаюсь сказать что продукт плохо работает, а пытаюсь сообщать об ошибках, которые могут помочь сделать BEST ещё лучше...

А вообще очень хороший бокс. Сильно помогает с правкой многих телефонов относительно слетевших сертификатов и не только.

JayDi

21.07.2011, 14:50

Дык, эта тема для того и есть - все проблемы, ошибки и прочее утраняем по мере нахождения :)

Shmastik

21.07.2011, 15:44

Nokia 5250 вычитал почему-то как 5233

Reading Phone Info....
Connected phone - Nokia 5233
Software ver : V ICPR72_10w21.2.1 06-07-10 RM-684 (c) Nokia
IMEI : 353772047439978
Ape Ver : V 10.0.011
APE Var : V 10.0.011??????
APE ADSP: 256
DSP Ver : fox_ICPR72_10w16_p2
APE Test: eno_version
PPM :
CNT :
Product SN : 0A3FFA5AA
Product code : 059D1W6
Base Prd.code: 0595902
Module code : 0204597
Long Prod.SN : 0
Hardware info=======
HWID : 1000
Retu : 16
Tahvo : 22
Batery: 3724 mV
Camera:
CMT BT:
APE BT: HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12708.
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI : 353772047439978
IMEI spNet : 3A 35 77 02 74 34 99 07
IMEI svNet : 33 35 77 02 74 34 99 07 F1

Conf key : 0000000000000000
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

AABBCC

21.07.2011, 16:41

Nokia 5250 вычитал почему-то как 5233

У меня всё ок вычитывает, v1.24.1.
Phone found!
Series 60 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia 5250
Software ver : V ICPR72_10w42.1 23-11-10 RM-684 (c) Nokia
IMEI : 353772045700942
Ape Ver : V 20.0.004
APE Var : V 20.0.004??????
APE ADSP: 256
DSP Ver : ICPR72_10w33
APE Test: eno_version
PPM :
CNT : v 001_000 22-07-10 vanilla RM684
Product SN : 07099D7AA
Product code : 059D1W6
Base Prd.code: 0595902
Module code : 0204597
Long Prod.SN : 0
Hardware info=======
HWID : 1000
Retu : 16
Tahvo : 22
Batery: 3765 mV
Camera:
CMT BT:
APE BT: HCI Version 12 (rev. 8192). LMP Version 12 (rev. 0). Manufacturer 12708.
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI : 353772045700942
IMEI spNet : 3A 35 77 02 54 07 90 04
IMEI svNet : 33 35 77 02 54 07 90 04 F8

Conf key : 0000000000000000
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

User code : Crypted
UserDataExLevel : Low [Gallery]

Done!

Shmastik

21.07.2011, 17:54

У меня всё ок вычитывает, v1.24.1.

Вычитывал и на v1.24 и на v1.24.1

JayDi

21.07.2011, 21:49

Это РР виноват :)

komayo

22.07.2011, 13:41

Почему на 1.24.2 версии DCT4 телефоны не прошивает?

card found: S/N 1********
registered to: komayo

Connect phone on selected interface...

UFS S/N 38442 boot - Ok

Connect phone on selected interface...

Phone found!
Series 40 Device detected! [DCT4+]
read info... - Ok

Reading Phone Info....
SW ver : V 09.85 11-03-10 RM-512 (c) Nokia
IMEI : 356248042604848
PPM : V 09.85
11-03-10
RM-512
(c) Nokia
EL
CNT : Content: ssa_a_red
V 09.85
11-03-10
RM-512
(c) Nokia

DSP Ver : PR72_09w52_U
PCode : 0576895
BPCode : 0569925
HWID : 1001
LCDVer : SUEZ
IMEI : 356248042604848
Sl Conf : 001-01-00000000000
Sl Prof : 800000000003000-B
Sl Aux : 000B5555
Hw Sig : D05CF47FC82AA4E0
Provider : Default Test Operator

Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;

Done!

Core version : 1.24.2 , Rev : 2.1

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm512__09.85.mcusw
PPM : rm512__09.85.ppm_el
CNT : rm512__09.85.image_el_bla
Check FlashFiles, Please, wait...
Bad file : rm512__09.85.mcusw
Bad file : rm512__09.85.ppm_el
Bad file : rm512__09.85.image_el_bla
Bad Flash files detected, will break procedure :(

Даже изменял Check mode, на DCT4 с Setting-а не хочет прошивать, может я что та не так делаю?:kos:

ildar

22.07.2011, 14:23

Series 40 Device detected! [DCT4+]
read info... - Ok

DCT4+ через JAF шьет без проблем.

vetalsoft

22.07.2011, 14:59

Почему на 1.24.2 версии DCT4 телефоны не прошивает?

Даже изменял Check mode, на DCT4 с Setting-а не хочет прошивать, может я что та не так делаю?:kos:

Там всё в логе написано. Не проходит верификация файлов прошивки. Если уверен на все сто, что пакет не битый, отключи в ini-файле проверку файлов и пробуй.

JayDi

22.07.2011, 16:16

Программа просто не шьет через уфс потому, что глючит там очень все при прошивке. Поэтому выкидывает ошибку проверки файлов. Все никак не могу доделать ее - времени не хватает =(

komayo

22.07.2011, 16:27

Программа просто не шьет через уфс потому, что глючит там очень все при прошивке. Поэтому выкидывает ошибку проверки файлов. Все никак не могу доделать ее - времени не хватает =(

Вот это другое дело, я так подумал что глюк с моей стороны, BEST наверно предназначен только для BB5 телефонов :wink:

JayDi

22.07.2011, 16:39

Да нет, шить будет, просто через JAF все пошло как по маслу - шьет без проблем, а вот UFS - Сарас видимо траву хорошую курил, когда писал режимы ифункции коробки - с ней почти невозможно работать иногда...

JayDi

23.07.2011, 12:56

N900, моя имплементация движка прошивки.
Будет позволять шить

Boot
CMT часть
APE часть
MMC образ

прошивка boot+cmt
Connect phone on selected interface...

Press and hold "U" button and insert cable!
Waiting for NOLO...
Connect in NOLO mode Ok!

Phone Info :
Type : RX-51 , HWRev : 2204
NOLO : 01/0E/14
SWVer: RX-51_2009SE_20.2010.36-2_PR_MR0

Read info Ok

Core RX-51_2009SE_20.2010.36-2_PR_COMBINED_MR0_ARM.bin.mcusw
Processing NOL part
BLK_INF : 2nd
BLK_VER : 1.4.14.9+0m5
BLK_LEN : 0x00003980
HW TYPE : RX-51
HW REV : 2201 , 2202 , 2203 , 2204 , 2205 , 2206 , 2207 , 2208 , 2209 , 2210 , 2211 , 2212 , 2213 , 2214 , 2215 , 2216
BLK_INF : xloader
BLK_VER : 1.4.14.9+0m5
BLK_LEN : 0x00003A00
HW TYPE : RX-51
HW REV : 2201 , 2202 , 2203 , 2204 , 2205 , 2206 , 2207 , 2208 , 2209 , 2210 , 2211 , 2212 , 2213 , 2214 , 2215 , 2216
Processing : xloader , 1.4.14.9+0m5
BLK_INF : secondary
BLK_VER : 1.4.14.9+0m5
BLK_LEN : 0x0001AB80
HW TYPE : RX-51
HW REV : 2201 , 2202 , 2203 , 2204 , 2205 , 2206 , 2207 , 2208 , 2209 , 2210 , 2211 , 2212 , 2213 , 2214 , 2215 , 2216
Processing : secondary , 1.4.14.9+0m5
NOL part Ok, boot flash done
Core RX-51_2009SE_20.2010.36-2_PR_COMBINED_MR0_ARM.bin.mcusw
Processing CMT part
BLK_INF : cmt-2nd
BLK_VER : BB5_09.36
BLK_LEN : 0x00013E00
Processing : cmt-2nd , BB5_09.36
BLK_INF : cmt-algo
BLK_VER : BB5_09.36
BLK_LEN : 0x0007EE80
Processing : cmt-algo , BB5_09.36
BLK_INF : cmt-mcusw
BLK_VER : rx51_ICPR82_10w08
BLK_LEN : 0x005B0A80
Processing : cmt-mcusw , rx51_ICPR82_10w08
CMT part prepare Ok, files are send
Programm CMT request Ok
Switch : OSSO UART+USB
Version : RX-51_2009SE_20.2010.36-2_PR_MR0
Switch CMT request Ok
CMT : Erasing...
CMT : Programm...
CMT : Programm Finished!

попробую максимально детальный дебаг всего процесса сделать, для отловки HW проблем при прошивке.

AABBCC

23.07.2011, 19:17

Пытаюсь восстановить ST_SECURITY => DAMAGED :( в RM-133 N-73 с помощью новой функции в 1.24.2. (- Added Variant cert recover (N73 security repair) on Restore CCC/HWC)
ТА восстановлен после воды, но: нормально шьётся, стирается. SDD, Simlock repair без проблем.
Вот его Selftest
Initializing Tests...
IMEI : 352916022020292 , Phone : RM-133 Nokia N73
Get keys...
PASSED | ST_TAHVOINT_TEST
PASSED | ST_UEM_CBUS_IF_TEST
PASSED | ST_EAR_DATA_LOOP_TEST
PASSED | ST_SIM_CLK_LOOP_TEST
PASSED | ST_SIM_IO_CTRL_LOOP_TEST
PASSED | ST_SIM_LOCK_TEST
MINOR | ST_SECURITY_TEST
PASSED | ST_PWR_KEY_TEST
PASSED | ST_CURRENT_CONS_TEST
PASSED | ST_BACKUP_BATT_TEST
PASSED | ST_CMT_APE_WAKEUP_TEST
PASSED | ST_SLEEPCLK_FREQ_TEST
PASSED | ST_RADIO_TEST
PASSED | ST_HOOKINT_TEST
PASSED | ST_BTEMP_TEST
PASSED | ST_VIBRA_TEST
->ERROR | ST_MBUS_RX_TX_LOOP_TEST
PASSED | ST_EXT_DEVICE_TEST
PASSED | ST_IR_LOOP_TEST
PASSED | ST_KEYBOARD_STUCK_TEST
PASSED | ST_LPRF_IF_TEST
PASSED | ST_CAMERA_IF_TEST
PASSED | ST_CAMERA_ACCELERATOR_TEST
PASSED | ST_SEC_CAMERA_IF_TEST
PASSED | ST_CAMERA_AUTOFOCUS_TEST
PASSED | ST_LPRF_AUDIO_LINES_TEST
PASSED | ST_MAIN_LCD_IF_TEST
PASSED | ST_BT_WAKEUP_TEST
SelfTests end

Read Info:
Phone found!
Series 60 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia N73
Software ver : V 05wk47v61.1 09-07-08 RM-133 (c) Nokia.
IMEI : 352916022020292
Ape Ver :
APE Var :
APE ADSP:
DSP Ver : scarfe_mc.05wk46v50p2
APE Test:
PPM :
CNT :
Product SN : SBH144666
Product code : 0563983
Base Prd.code: 0527006
Module code : 0202855
Long Prod.SN :
Hardware info=======
HWID : 6000
Retu : 15
Tahvo : 22
Batery: 4191 mV
Camera:
CMT BT:
APE BT:
APE HW:
LCDVer:
RF ic : 17211721
Lock info ===========
IMEI : 352916022020292
IMEI spNet :
IMEI svNet :

Conf key : 0000000000000000
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
User Code : 12345
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Check:
Connect phone on selected interface...

Read and Check phone data...
Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST : C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : 737A24E08BE12AC7442EE56F8F02D39F3A782F52
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 1F200106FD5D025443452F4AE2339FC2BCAFA9C7
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU configuration
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLASHID : 22E800EC , CMT , NOR
FLCNT : 00000000000000000000000000000000000000
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
FLASHID : 0000FFFF , CMT , MMC , EXT
TransmissionReq : 16 bit, Single
TransmissionReq : Accepted, 16 bit, Single
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU configuration
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLASHID : 00A100EC , APE , NAND
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_xsr15_flash_alg.fg , Rev : 0.0 Ver : 1.49.0
APE Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD
Boot done!

Switch jaf to FBUS...
FbusMode set Ok

SimLock status : SimLock is Ok
Security status : Security Damaged!!!!! :(
SDD Key status : SD Data is Ok

Лог стирания, затем прошивки:

Switch jaf to FBUS...
FbusMode set Ok

User ACCEPTED FULL ERASE
Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST : C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : 737A24E08BE12AC7442EE56F8F02D39F3A782F52
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 1F200106FD5D025443452F4AE2339FC2BCAFA9C7
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU configuration
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLASHID : 22E800EC , CMT , NOR
FLCNT : 00000000000000000000000000000000000000
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
FLASHID : 0000FFFF , CMT , MMC , EXT
TransmissionReq : 16 bit, Single
TransmissionReq : Accepted, 16 bit, Single
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU configuration
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLASHID : 00A100EC , APE , NAND
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_xsr15_flash_alg.fg , Rev : 0.0 Ver : 1.49.0
APE Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD
Boot done!

Full Erase started...
Asic : CMT , Sub : NOR
Erase Area 0x00000000-0x00FFFFFF
Init Erase Mode Ok
Using TimeOut : 10 min ( 600 sec )
Erasing, wait.....
Erase CMT : erase Ok

Switch jaf to FBUS...
FbusMode set Ok

Phone disconected!

Connect phone on selected interface...

-> Phone not found.. :(

Fetching failed!

Connect phone on selected interface...

Read fail...!

Read and Check phone data...
Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST : C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : 737A24E08BE12AC7442EE56F8F02D39F3A782F52
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 1F200106FD5D025443452F4AE2339FC2BCAFA9C7
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU configuration
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLASHID : 22E800EC , CMT , NOR
FLCNT : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
FLASHID : 0000FFFF , CMT , MMC , EXT
TransmissionReq : 16 bit, Single
TransmissionReq : Accepted, 16 bit, Single
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBReq : Blank (Erased or HW error)

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU configuration
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLASHID : 00A100EC , APE , NAND
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_xsr15_flash_alg.fg , Rev : 0.0 Ver : 1.49.0
APE Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBReq : Blank (Erased or HW error)
Boot done!

Switch jaf to FBUS...
FbusMode set Ok

Phone not found :(

Connect phone on selected interface...

Connect phone on selected interface...

Core version : 1.24.2 , Rev : 2.1

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : N73_4.0839.42.2.1_western_C00_PRD_cc.fpsx
PPM : N73_rofx_4.0839.42.2.1_PRD.V01
CNT : N73_userarea_4.0839.42.2.1.U01
Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST : C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : 737A24E08BE12AC7442EE56F8F02D39F3A782F52
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 1F200106FD5D025443452F4AE2339FC2BCAFA9C7
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU configuration
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLASHID : 22E800EC , CMT , NOR
FLCNT : 000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
FLASHID : 0000FFFF , CMT , MMC , EXT
TransmissionReq : 16 bit, Single
TransmissionReq : Accepted, 16 bit, Single
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBReq : Blank (Erased or HW error)

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU configuration
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLASHID : 00A100EC , APE , NAND
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_xsr15_flash_alg.fg , Rev : 0.0 Ver : 1.49.0
APE Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBReq : Blank (Erased or HW error)
Boot done!

Partitioning....
Partitioning Ok...
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
Erase : Processing N73_4.0839.42.2.1_western_C00_PRD_cc.fpsx
Init Erase Mode Ok
Found 4 areas to erase, erase group
Asic : CMT , Sub : NOR
CMT , NOR , Area : 0x00080000 - 0x00731951
CMT , NOR , Area : 0x00000000 - 0x0005FFFF
CMT , NOR , Area : 0x001E0000 - 0x001FFFFF
CMT , NOR , Area : 0x00880000 - 0x00FEFFFF
Using TimeOut : 7 min ( 430 sec )
Erasing, wait.....
CMT : Group erase Ok
Found 4 areas to erase, erase group
Asic : APE , Sub : NAND
APE , NAND , Area : 0x00000000 - 0x0007FFFF
APE , NAND , Area : 0x00080000 - 0x000FFFFF
APE , NAND , Area : 0x00100000 - 0x0025FFFF
APE , NAND , Area : 0x003C0000 - 0x04E1FFFF
Erasing, wait.....
APE : Group erase Ok
TIME : Erase time : 00:00:06
PrReq : NOR, 00
PrReq : NAND, 010300000000000000000000000000
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
Write : Processing N73_4.0839.42.2.1_western_C00_PRD_cc.fpsx
Init Write Mode Ok
CMT: Writing Hash CERT [NOLO]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [UPDAPP]
CMT: Writing Hash CERT [ADL]
CMT: Writing Hash CERT [DSP0]
CMT: Writing Hash CERT [MCUSW]
APE: Writing Hash CERT [KEYS]
APE: Writing Hash CERT [X-LOADER]
APE: Writing Hash CERT [PRIMAPP]
APE: Writing Hash CERT [SOS+LOADER]
APE: Writing Hash CERT [SOS*UPDAPP]
APE: Writing Hash CERT [SOS+UZIP]
APE: Writing Hash CERT [PAPUBKEYS]
APE: Writing Hash CERT [PASUBTOC]
APE: Writing Hash CERT [ADL]
APE: Writing Hash CERT [SOS+XZIP]
APE: Writing Hash CERT [SOS*CORE]
APE: Writing Hash CERT [SOS+ROFS]
APE: Writing Hash CERT [SOS+ROFX]
Total writen 1770 blocks
TIME : Write time : 00:04:37
PrReq : NOR, 00
PrReq : NAND, 010300000000000000000000000000

Partitioning....
Partitioning Ok...
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
Erase : Processing N73_rofx_4.0839.42.2.1_PRD.V01
Init Erase Mode Ok
Found 1 areas to erase, erase group
Asic : APE , Sub : NAND
APE , NAND , Area : 0x03920000 - 0x04E1FFFF
Erasing, wait.....
APE : Group erase Ok
TIME : Erase time : 00:00:01
PrReq : NOR, 00
PrReq : NAND, 010300000000000000000000000000
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
Write : Processing N73_rofx_4.0839.42.2.1_PRD.V01
Init Write Mode Ok
APE: Writing Hash CERT [SOS+ROFX]
Total writen 2052 blocks
TIME : Write time : 00:02:43
PrReq : NOR, 00
PrReq : NAND, 010300000000000000000000000000

TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
Erase : Processing N73_userarea_4.0839.42.2.1.U01
Init Erase Mode Ok
Found 1 areas to erase, erase group
Asic : APE , Sub : NAND
APE , NAND , Area : 0x04E20000 - 0x07C9FFFF
Erasing, wait.....
APE : Group erase Ok
TIME : Erase time : 00:00:01
PrReq : NOR, 00
PrReq : NAND, 010300000000000000000000000000
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
Write : Processing N73_userarea_4.0839.42.2.1.U01
Init Write Mode Ok
Total writen 367 blocks
TIME : Write time : 00:01:02
PrReq : NOR, 00
PrReq : NAND, 010300000000000000000000000000

Switch jaf to FBUS...
FbusMode set Ok

Phone connected
Reading Phone Info....
Connected phone - Nokia N73
Software Info: V 05wk47v61.1
09-07-08
RM-133
(c) Nokia.
IMEI: 12345610654321?
Product code:
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Resetting LifeTimer
Reset Done!
AfterFlash operations done... Reconnect, wait...
Flashing done

Лог восстановления NPC, SDD,Simlock, SX4, Upload Tune:
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (APE)
Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST : C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : 737A24E08BE12AC7442EE56F8F02D39F3A782F52
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 1F200106FD5D025443452F4AE2339FC2BCAFA9C7
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU configuration
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLASHID : 22E800EC , CMT , NOR
FLCNT : 00000000000000000000000000000000000000
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
FLASHID : 0000FFFF , CMT , MMC , EXT
TransmissionReq : 16 bit, Single
TransmissionReq : Accepted, 16 bit, Single
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU configuration
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLASHID : 00A100EC , APE , NAND
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_xsr15_flash_alg.fg , Rev : 0.0 Ver : 1.49.0
APE Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD
Boot done!

Preparing for write certificates...

Switching to CMT...

Erase NPC... Ok
Writing NPC... Ok

CMT cert write done!

Done!

Connect phone on selected interface...

Switch jaf to FBUS...
FbusMode set Ok

Phone found!
Series 60 Device detected!
read info... - Ok

Repair SD procedure started...

Phone Imei: 352916022020292
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing Super Dongle Key... Ok
Done!

Local SX4 procedure started...

Phone Imei: 352916022020292
Key file exists, no need to read...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Upload PM checked
Uploading RF/Battery tune to phone...
Using : RM-133.pm
Operating mode is OK, no need change...

Field 1
Record 0 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 6 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 16 write - Ok
Record 18 write - Ok
Record 20 write - Ok
Record 22 write - Ok
Record 23 write - Ok
Record 24 write - Ok
Record 25 write - Ok
Record 26 write - Ok
Record 28 write - Ok
Record 29 write - Ok
Record 31 write - Ok
Record 33 write - Ok
Record 34 write - Ok
Record 44 write - Ok
Field 309
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 17 write - Ok
Record 22 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => DAMAGED :(

Done!

Elapsed: 00:01:04

Upload done

А вот самый интересный момент Restore CCC\HWR не срабатывает:
Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Will Write CCC/HWC keys now...

Using : RM-133.rpl
Variant Data found!

Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST : C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : 737A24E08BE12AC7442EE56F8F02D39F3A782F52
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 1F200106FD5D025443452F4AE2339FC2BCAFA9C7
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU configuration
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLASHID : 22E800EC , CMT , NOR
FLCNT : 00000000000000000000000000000000000000
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
FLASHID : 0000FFFF , CMT , MMC , EXT
TransmissionReq : 16 bit, Single
TransmissionReq : Accepted, 16 bit, Single
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU configuration
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLASHID : 00A100EC , APE , NAND
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_xsr15_flash_alg.fg , Rev : 0.0 Ver : 1.49.0
APE Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD
Boot done!

Preparing for write certificates...

CMT : Read NPC certificate...
Repair Data Check Error :(

CMT cert write done!

Done!

Не могу понять ТА не восстановлен по HW до конца, или новая фишка в 1.24.2 не работает?
Пробовал сделать Recovery CERT с помощью MX-Key в связке с UFS, не получилось. При буте выдаёт ошибку, HTI интерфейса у меня нет:
Using device: UFS_USB V2.8 (c) SarasSoft 2007.
Driver: usbohci:usbhub:usbhub:UFS2XX, ver: 3.6.0.0 , NTMP ver: 2.6.0.0
Module ver: 1.0.0.17841(12-07-2011), Library ver: 1.0.0.11875(12-07-2011)
APE Data :
SYSTEM ASIC ID: 17100708 [OMAP1710 ver: 2.0]
ASIC MODE ID: 00
PUBLIC ID: 737A24E08BE12AC7442EE56F8F02D39F3A782F52
ROOT KEY HASH: 49A97E826B93BA20B7ED0B082475C00500000000
ROM ID: 1DFD66132C872FD4
CMT Data :
SYSTEM ASIC ID: 000000010000022600010006010C192101003000 [RAP3G ver: PA 3.0]
EM0 ID: 00000295
EM1 ID: 00000B22
PUBLIC ID: 1F200106FD5D025443452F4AE2339FC2BCAFA9C7
ASIC MODE ID: 00
ROOT KEY HASH: BAF3A9C3DBFA8454937DB77F2B8852B1
ROM ID: 273F6D55DFAAF68F
SecondaryBoot: rap3gv3_2nd.fg [BB5] version: 9.11.1 revision: 0.0 size: 0x3C00
Supported Ids: 0103192101003000, 010C192101003000, 0103192101013000, 010C192101013000, 0103192101003100, 010C192101003100, 0303192101023000, 030C192101023000, 0303192101033000, 030C192101033000, 0103192101001101, 010C192101001101, 0003192101001002, 000C192101001002, 0013192101001002, 001C192101001002
Storage0: 00EC 22E8 - 0000 6921 [Samsung K8S2815ETB,128 Mbits] type: FLASH,NOR, asic:CMT
Storage content: 0000 0000 0000 0000 0000 0000 0000 0000
Storage1: FFFF 0000 - 0000 0000 type: MMC, asic:CMT
TransmissionMode: 16Bit
Algorithm: RAP3Gv3_algo.fg [BB5 ALGORITHM] version: 9.50.0 revision: 0.0 size: 0x23010
Supported Ids: 0103192101003000, 010C192101003000, 0103192101013000, 010C192101013000, 0103192101003100, 010C192101003100, 0303192101023000, 030C192101023000, 0303192101033000, 030C192101033000, 0003192101002000, 000C192101002000, 0003192101002100, 000C192101002100, 0003192101002200, 000C192101002200, 0003192101012200, 000C192101012200, 0103192101001101, 010C192101001101, 0003192101001002, 000C192101001002, 0013192101001002, 001C192101001002
CMT PAPUBKEYS HASH: 5E8D0D504A0902E261268C14FCD8A2C9093523BC
TransmissionMode: DDR&TX2
SecondaryBoot: helen3_2nd.fg [BB5] version: 1.35.0 revision: 0.0 size: 0x3500
Supported Ids: 17100700, 17100701, 17100702, 17100703, 17100704, 17100708
loader not responding (0910000000B172)
P.S. нашёл в мастерской ещё одну N73, всё рабочее, кроме камеры:
Phone found!
Series 60 Device detected!
read info... - Ok

Read and Check phone data...
Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST : C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : DD7F4FC6A6314137C43E0C452511F20FEB356ADA
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 2060010C5375025476EDE34D3D9D947CC2292ACC
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU configuration
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLASHID : 22E800EC , CMT , NOR
FLCNT : 00000000000000000000000000000000000000
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
FLASHID : 0000FFFF , CMT , MMC , EXT
TransmissionReq : 16 bit, Single
TransmissionReq : Accepted, 16 bit, Single
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU configuration
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLASHID : 00A100EC , APE , NAND
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_xsr15_flash_alg.fg , Rev : 0.0 Ver : 1.49.0
APE Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD
Boot done!

Switch jaf to FBUS...
FbusMode set Ok

SimLock status : SimLock is Ok
Security status : Security is Ok
SDD Key status : SD Data is Ok

PA_SimLock Version :
PA_SL phone detected

Done!

Connect phone on selected interface...

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia N73
Software ver : V 05wk47v61.1 09-07-08 RM-133 (c) Nokia.
IMEI : 352916026955634
Ape Ver :
APE Var :
APE ADSP:
DSP Ver : scarfe_mc.05wk46v50p2
APE Test:
PPM :
CNT :
Product SN : MYH507911
Product code : 0539284
Base Prd.code: 0537044
Module code : 0202855
Long Prod.SN :
Hardware info=======
HWID : 7600
Retu : 15
Tahvo : 22
Batery: 4621 mV
Camera:
CMT BT:
APE BT:
APE HW:
LCDVer:
RF ic : 17211721
Lock info ===========
IMEI : 352916026955634
IMEI spNet :
IMEI svNet :

Conf key : 0000000000000000
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
User Code : 00000
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Попробовал на ней повторить процедуру восстановления CCC/HWC, тоже не сработало:
Will Write CCC/HWC keys now...

Using : RM-133.rpl
Variant Data found!

Checking BUS...
Switch jaf to FlashMode...
FlashMode set Ok
Booting phone...

BOOT 1ST : C0

APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : DD7F4FC6A6314137C43E0C452511F20FEB356ADA
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4

CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 2060010C5375025476EDE34D3D9D947CC2292ACC
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU configuration
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLASHID : 22E800EC , CMT , NOR
FLCNT : 00000000000000000000000000000000000000
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
FLASHID : 0000FFFF , CMT , MMC , EXT
TransmissionReq : 16 bit, Single
TransmissionReq : Accepted, 16 bit, Single
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD

APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU configuration
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLASHID : 00A100EC , APE , NAND
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_xsr15_flash_alg.fg , Rev : 0.0 Ver : 1.49.0
APE Algo sent!
TransmissionReq : 32 bit, Dual
TransmissionReq : Accepted, 32 bit, Dual
PAPUBKeys : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD
Boot done!

Preparing for write certificates...

CMT : Read NPC certificate...
Repair Data Check Error :(

CMT cert write done!

Done!

Switch jaf to FBUS...
FbusMode set Ok

Elapsed: 00:01:17

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

На MX_key 3.5 rev 1.2 через UFS на этой N-73 выдаёт такую же ошибку при буте. Видимо всё сделано специально, чтобы покупали HTI.

JayDi

23.07.2011, 19:46

слейте с нерабочей этой NPC сертификат, гляну. Там привязка Variant идет к нему. Я только 7 вариантов подобрал, всего их около 40ка

AABBCC

23.07.2011, 20:05

Вот, с одной не рабочей и с другой рабочей.

Shmastik

24.07.2011, 13:03

Два варианта Rpl под продукт код, если совпадает продукт код то просто проливаеш и секюрити становится на место

Shmastik

24.07.2011, 13:13

По непонятной причине Best не сливает сертификат variant с N73. Привожу пример слитого RPL при помощи JAF и Best с одного и того-же телефона.

Shmastik

24.07.2011, 13:20

Вот, с одной не рабочей и с другой рабочей.

Если телефоны с одинаковым продукт кодом то можно вычитать RPL с помощью JAF (или другого бокса, я пробовал Jaf-ом), вырезаеш из него все кроме строк начинающихся с Variant, добавляеш к своему RPL (наверное можно и просто его пролить, но я не пробовал) и проливаеш в телефон. Мне этого хватило чтобы поднять N73 с ST_SECURITY => DAMAGED.

JayDi

24.07.2011, 14:01

Угу, заметил. Проверю.
В базе у менят есть 608 тип, а вот 795 не было.
Есть :
0539269
0539279
0545071
0541421
0529608
0539352
0552007

AABBCC

24.07.2011, 15:31

Если телефоны с одинаковым продукт кодом то можно вычитать RPL с помощью JAF (или другого бокса, я пробовал Jaf-ом), вырезаеш из него все кроме строк начинающихся с Variant, добавляеш к своему RPL (наверное можно и просто его пролить, но я не пробовал) и проливаеш в телефон. Мне этого хватило чтобы поднять N73 с ST_SECURITY => DAMAGED.
Считал Cyclone -ом RPL с другого N73, на продукт коды вообще не смотрел, то ли совпал, то ли не важен. Вставил Variant Data а так же всё что после в RPL пациента, залил назад Cyclone -ом, ТА заработал. То Shmastik:appl:
Прикрепляю RPL, из которого Variant Data помогли.

JayDi

24.07.2011, 15:39

Совпал)))

Спасибо, добавлю в базу сегодня. Заодно проверю почему вариант не читается с этого старья.

AABBCC

24.07.2011, 16:04

Совпал)))
В этой N-73 я продукт код не восстанавливал после стирания, у него его как такового получается и не было)) Вот что полсе Variant Data было в RPL:
[CERT_PROG_DATA_OUT_APE] и это всё.
А вот что было в рабочем ТА после Varinat Data, и я это тоже вставил в RPL, который залил, и теперь это уже вычитывается Cyclone -ом из восстановленного ТА , то есть эти строки прописываются. Может это повлияло?
[CERT_PROG_DATA_OUT_APE]
PRODUCTCODE=0539284
PSN=MYH507911
HWID=7600

JayDi

24.07.2011, 16:47

продукт код хранится в NPC.

NeOnyx

25.07.2011, 12:56

Может кто разумно объяснить что с серваком?

registered to: NeOnyx

Connect phone on selected interface...

Link to my account: http://user.infinity-best.com:82/
Login: ххххххх
Password: хххххххх

Connecting to server...

Server not found...
Error in job...

Link to my account: http://user.infinity-best.com:82/
Login: хххххххх
Password: ххххххх

Connecting to server...

Server not found...
Error in job...

JayDi

25.07.2011, 13:02

Обновляется.

BOSS®™

26.07.2011, 07:19

Версией 1.24.5 Успешно разлочен Nokia E65 RM-208, через уфс с первого раза прошло на ура сейчас ТА работает.

card found: S/N 00000000
registered to: BOSS

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia E65
Software ver : V 3.0615.3 31-01-08 RM-208 (c) Nokia.
IMEI : 353260000000000
Ape Ver : 3.0633.69.00 06-02-08 RM-208 (c)Nokia
APE Var : 3.0633.69.00_v05 06-02-08 RM-208 (c)Nokia
APE ADSP: 256
DSP Ver : A06w14PB_07w42
APE Test:
PPM :
CNT : CP_1.2
Product SN : SIH901551
Product code : 0536850
Base Prd.code: 0536849
Module code :
Long Prod.SN :
Hardware info=======
HWID : 0801
Retu : 15
Tahvo : 21
Batery: 4588 mV
Camera:
CMT BT:
APE BT:
APE HW: 1
LCDVer:
RF ic :
Lock info ===========
IMEI : 353260000000000
IMEI spNet : 3A 35 62 01 51 31 78 05
IMEI svNet : 33 35 62 01 51 31 78 35 F0

Conf key : FFFFFFFFFFFFFFFF
Provider key : FFFFFFFFFFFFFFFF

SL Error detected
= > SP Data Corrupted!!! Use Repair SL for Unlock/Repair phone!!!

Provider : Unknown Provider
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 1

LOCK STATUS :
=============================
BLK : 1
Lock1:Close
=============================
LOCKS : Closed
=============================
CRT308 Backup Created

User Code : Not Set
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Checking StartUp data ...
-----------------------
SDD Key status : SDData Damaged!!!!! :(
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!

Phone found!
Series 60 Device detected!
read info... - Ok

Repair SD procedure started...

Phone Imei: 353260000000000
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing Super Dongle Key... Ok
Done!

Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!! :(
-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!

Local SX4 procedure started...

Phone Imei: 353260000000000
Key file exists, no need to read...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Upload PM checked
Uploading RF/Battery tune to phone...
Using : RM-208.pm
Operating mode is OK, no need change...

Field 1
Record 0 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 6 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 16 write - Ok
Record 18 write - Ok
Record 20 write - Ok
Record 22 write - Ok
Record 23 write - Ok
Record 24 write - Ok
Record 25 write - Ok
Record 26 write - Ok
Record 28 write - Ok
Record 29 write - Ok
Record 31 write - Ok
Record 33 write - Ok
Record 34 write - Ok
Record 44 write - Ok
Field 309
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 17 write - Ok
Record 22 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => OK

Done!

Elapsed: 00:00:01

Upload done

Repair SL procedure started...

Phone Imei: 353260000000000
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing SimLock Data... Ok
Writing SimLock Key... Ok
Done!

Reading Phone Info....
Connected phone - Nokia E65
Software ver : V 3.0615.3 31-01-08 RM-208 (c) Nokia.
IMEI : 353260000000000
Ape Ver : 3.0633.69.00
06-02-08
RM-208
(c)Nokia
APE Var : 3.0633.69.00_v05
06-02-08
RM-208
(c)Nokia
APE ADSP: 256
DSP Ver : A06w14PB_07w42
APE Test:
PPM :
CNT : CP_1.2
Product SN : SIH901551
Product code : 0536850
Base Prd.code: 0536849
Module code :
Long Prod.SN :
Hardware info=======
HWID : 0801
Retu : 15
Tahvo : 21
Batery: 4577 mV
Camera:
CMT BT:
APE BT: HCI Version 2 (rev. 0). LMP Version 2 (rev. 3504). Manufacturer 13.
APE HW: 1
LCDVer:
RF ic : 17141714
Lock info ===========
IMEI : 353260000000000
IMEI spNet :
IMEI svNet :

Conf key : 0000000000000000
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
User Code : Not Set
UserDataExLevel : Full [PhoneBook, Calendar, PWD, SMS, Gallery]

Done!

Checking StartUp data ...
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!
:appl::appl::appl:

aq7

26.07.2011, 14:04

не могу пройти локальную sx4 авторизацию,телефон 5130,интерфейс ufs,Версиея 1.24.5
-----------------------
SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!! :(
-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

Local SX4 procedure started...

Phone Imei: 354223033005463
Key file exists, no need to read...
Step 1...
Step 2...
SX4 Auth fail...

сyclone без проблем

DrManila

26.07.2011, 14:24

aq7, по идее она сработает если восстанавливали SD BEST'ом, у Cyclone такой привязки нет. Если SD заводская сделайте серверную SX4.

PANsoft

26.07.2011, 14:46

aq7, по идее она сработает если восстанавливали SD BEST'ом, у Cyclone такой привязки нет. Если SD заводская сделайте серверную SX4.

Phone found!
Series 40 Device detected!
read info... - Ok

Local SX4 procedure started...

Phone Imei: 356919035519785
Key file exists, no need to read...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Done!

только что на 5130 с заводским ключем..... Какой там ключ, заводской или нет значения не имеет. Скорее всего проблемма в коммуникации уфс, ну или Read Key процедура прошла с ошибкой.

aq7

26.07.2011, 14:57

проверил сейчас работает,но такое было на пару апаратах,возможно помогает перезапуск приложения,постараюсь более точно выловить баг и отрапортовать

JayDi

26.07.2011, 15:02

При репайренной SD над галочку Custom keys тыцнуть.

PANsoft

26.07.2011, 22:34

При репайренной SD над галочку Custom keys тыцнуть.

Касательно этой модели - нет разницы, родной или не родной ключ. Галка Use custom key нужна только для rapido где пока не реализована процедура декрипта человеческого.

Phone found!
Series 40 Device detected!
read info... - Ok

Repair SD procedure started...

Phone Imei: 356919035519785
Key file exists, no need to read...
Accepted SdRepReq (on alive SD) by user
Check phone mode...
Phone in Normal mode
Seting Test mode... wait...
Test mode set
Writing Super Dongle Key... Ok!
Done!

Local SX4 procedure started...

Phone Imei: 356919035519785
Key file exists, no need to read...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Done!

вот лог с кастомным ключем без галки.

valeraabh

05.08.2011, 20:40

Пришел 5330с-1, прошивка по USB
Лог прилагаю

Free

05.08.2011, 22:03

Пришел 5330с-1, прошивка по USB
Лог прилагаю

если не секрет что полезного в этом логе кроме серийника Вашего донгла?

valeraabh

05.08.2011, 22:06

если не секрет что полезного в этом логе кроме серийника Вашего донгла?

В каком смысле что полезного ?
И где серийник донгла ?

Free

05.08.2011, 22:11

В каком смысле что полезного ?
И где серийник донгла ?

.:: Скрытый текст (вы должны войти под своим логином или зарегистрироваться и иметь 34 сообщение(ий)) ::.

в смысле Вы хотели показать что телефон успешно прошит, или что?
лог начинается с RM-615 заканчивается RM-645
или это ребус может какой-то?

ZArchi

05.08.2011, 22:17

если не секрет что полезного в этом логе кроме серийника Вашего донгла?

:jok:Например, Конец гарантии: 24-12-2011 этого тела и не морочиться а отправить в сервис нокии.

valeraabh

05.08.2011, 22:21

Да телефон прошит успешно.
Ребуса нет никакого просто я сразу после прошивки 5330 попытался подцепить C5 вот видно и серийник с кусочком лога прописался