Re: Samsung P7500 нужно восстановить bootloader
#34
Цитата:
Сообщение от geras
Нужно немного поподробней? Как именно восстанавливаете? SBK/MSL используете?
|
C помощью nvflash по USB, SBK есть.
Лог в Z3X
Развернуть для просмотра
Цитата:
Z3X EasyJtag Software ver. 2.5.0.8
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0700901A902230A8, ,FW Ver.: 01.58
CMD Pullup Level:1949 mV
CMD Active Level:1990 mV
Box IO Level:2800 mV
CLK Rate:21000 khz
HiPower mode is ON!
---------- eMMC Device Information ----------
EMMC CID : 1501004D41473446411221171C459EB4
EMMC CSD : D02701320F5903FFF6DBFFEF8A404066
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 09/2011 Rev.0x12
EMMC NAME: MAG4FA , S/N: 555162693
EMMC NAME (HEX): 4D414734464100
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: MAG4FA_ 555162693_20170414_1454.extcsd
=============================================
Extended CSD rev 1.5 (MMC 4.41)
=============================================
......
Searching for partition tables...
Detected NVIDIA...
NVIDIA TABLE detected...
Wrning: NVIDIA PT Offset : 200000
Boot RVA Correction : 100000
Header ID: D2CF02183AB52E86F9E134788A486507
Warning: Header Size = 1360
Warning: Entries Count = 16
MMCBLK0P0 (BCT) Adress in BOOT1+BOOT2 0x0, Length: 0x600000
MMCBLK0P1 (PT) Adress in USER: 0x500000, Length: 0x100000
MMCBLK0P2 (EBT) Adress in USER: 0x600000, Length: 0x400000
MMCBLK0P3 (EB2) Adress in USER: 0xA00000, Length: 0x400000
MMCBLK0P4 (GP1) Adress in USER: 0xE00000, Length: 0x800000
MMCBLK0P5 (EFS) Adress in USER: 0x1600000, Length: 0x1800000
MMCBLK0P6 (SOS) Adress in USER: 0x2E00000, Length: 0xA00000
MMCBLK0P7 (LNX) Adress in USER: 0x3800000, Length: 0x1000000
MMCBLK0P8 (APP) Adress in USER: 0x4800000, Length: 0x48400000
MMCBLK0P9 (CAC) Adress in USER: 0x4CC00000, Length: 0x38000000
MMCBLK0P10 (MSC) Adress in USER: 0x84C00000, Length: 0x400000
MMCBLK0P11 (MDM) Adress in USER: 0x85000000, Length: 0x1800000
MMCBLK0P12 () Adress in BOOT1+BOOT2 0x0, Length: 0x0
Done...Presets has been updated...
Done.
Running:SAMSUNG: Read S.M.A.R.T Report...
Z3X EasyJtag Software ver. 2.5.0.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:1949 mV
CMD Active Level:1990 mV
Box IO Level:2800 mV
CLK Rate:21000 khz
Reading S.M.A.R.T
S.M.A.R.T Ver. 0 , Card Error mode : Normal
Super Block size : 0x00400000 (4194304 bytes)
Super Page size : 0x00008000 (32768 bytes)
Optimal Write size : 0x00008000 (32768 bytes)
Read Reclaim count : 0
Optimal TRIM size : 0x00040000 (262144 bytes)
Total Number of banks : 2
Initial bad blocks per bank : 4,4,0,0
Runtime bad blocks per bank : 0,0,0,0
Reserved blocks left per bank : 137,137,0,0
All Erase counts (min,avg,max): 9,182,564
SLC Erase counts (min,avg,max): 19,177,564
MLC Erase counts (min,avg,max): 9,182,564
S.M.A.R.T Report Done.
|
[свернуть]