======================================================
======================================================
       eMMC Test Point Connection Module             
======================================================
======================================================
                                                      
1. Make Sure CLK Test Point is already Soldered       
2. Make Sure CMD Test Point is already Soldered       
                                                      

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 150100303030303030562012063058CF
CSD : 902701320F5903FFF6DBFFEF8A404023

eMMC Boot Information
Revision 1.5 (for MMC v4.41)
BOOT PARTITION     : NOT BOOT ENABLED
PARTITION ACCESS   : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT  : DISABLED
BOOT MODE          : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH    : ENABLED
eMMC FirmW UPDATE  : DISABLED
EMMC CACHE SIZE    : 0 KB
SUPER PAGE SIZE    : 4096 KB
HC ERASE GROUP SIZE: 512 KB
USER AREA SIZE     : 8589934592 BYTES
BOOT PARTITION SIZE: 512 KB
RPMB PARTITION SIZE: 128 KB


eMMC Device Information
Manufacturer ID: SAMSUNG
Device Type    : Embedded BGA
Application ID : 00
Product Name   : 000000
Product Rev    : 5.6
Product SN     : 20120630
Manufactured   : January 2005

Card Specific Data
CSD_STRUCTURE     : Version 1.2
SPEC_VERS         : Version 4.1/4.2/4.3
TAAC              : 13 ns
TRAN_SPEED        : 4000000 KHz
READ_BL_LEN       : 512 Bytes
C_SIZE            : HIGH CAPACITY
WP_GRP_ENABLE     : YES
WRITE_BL_LEN      : 512 Bytes
CONTENT_PROT_APP  : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
150100303030303030562012063058CF.ext_csd
Backup Directory:
C:\ATF\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\


Task Selected: Samsung eMMC Firmware Update
======================================================
--> This will ERASE USER AREA, BOOT1, BOOT2, and RPMB 
--> This will RESET EXT_CSD Programming Such as BOOT  
    Options, Bus Characteristics and Partition Sizes..
======================================================

Please Manually Select the Correct
Part Number of your eMMC Device.

======================================================
If you select a WRONG PART NUMBER, then
YOU WILL PROBABLY KILL THE EMMC !!!
======================================================

======================================================
Loading ATF eMMC Firmware File... (Please Wait)       
======================================================

 
File Author: ATF Team @ SmartGSM
Date Created: 18/06/2015 (dd/mm/yyyy)
Description: Samsung eMMC Firmware
eMMC Part Number: KLMBG4GEAC-B001
eMMC Product Name: MBG4GC
eMMC Product Rev: 0.3

Preparing eMMC for Firmware Update...
Sending eMMC Firmware Blocks...
All Blocks Sent!
NAND Write Delay: 1 Second (Please Wait)
Applying eMMC Firmware Update...
Waiting for Device Re-Initialization...
Firmware Write Protect Delay: 1 Second (Please Wait)
Checking eMMC Firmware Update Status...
Applying Final Patches...
eMMC Firmware Update Successful!


======================================================
  Your eMMC is now a Brand New BLANK Device!!!
======================================================
Resize BOOT and RPM Partitions if needed...           
ReWrite BOOT1, BOOT2 and USER Partitions if needed... 
ReWrite EXT_CSD File if needed...                     
Make sure eMMC BOOT Options are Correct for your Phone
======================================================

Total Elapsed Time 00:00:47

======================================================
======================================================
       eMMC Test Point Connection Module             
======================================================
======================================================
                                                      
1. Make Sure CLK Test Point is already Soldered       
2. Make Sure CMD Test Point is already Soldered       
                                                      

Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 1501004D4247344730031108B47350F7
CSD : D02701320F5903FFF6DBFFEF8E40400D

eMMC Boot Information
Revision 1.6 (for MMC v4.5, v4.51)
BOOT PARTITION     : NOT BOOT ENABLED
PARTITION ACCESS   : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT  : DISABLED
BOOT MODE          : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH    : ENABLED
eMMC FirmW UPDATE  : DISABLED
EMMC CACHE SIZE    : 0 KB
SUPER PAGE SIZE    : 3584 KB
HC ERASE GROUP SIZE: 512 KB
USER AREA SIZE     : 31268536320 BYTES
BOOT PARTITION SIZE: 4096 KB
RPMB PARTITION SIZE: 4096 KB


eMMC Device Information
Manufacturer ID: SAMSUNG
Device Type    : Embedded BGA
Application ID : 00
Product Name   : MBG4G0
Product Rev    : 0.3
Product SN     : 1108B473
Manufactured   : May 1997

Card Specific Data
CSD_STRUCTURE     : Extended
SPEC_VERS         : Version 4.1/4.2/4.3
TAAC              : 13 ns
TRAN_SPEED        : 4000000 KHz
READ_BL_LEN       : 512 Bytes
C_SIZE            : HIGH CAPACITY
WP_GRP_ENABLE     : YES
WRITE_BL_LEN      : 512 Bytes
CONTENT_PROT_APP  : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
1501004D4247344730031108B47350F7.ext_csd
Backup Directory:
C:\ATF\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\