Re: E5-00 только вибро...
#9
Цитата:
Сообщение от KonstantinVoskr
Вы издеваетесь что ли?
Окей, ня ...
|
Да скачал я его с другого файлообменника,что сразу минус то лепите,я уже совсем красный стал.Теперь еще один вопрос,как залить это ПО Stress Test,BEST не видит эти файлы.Плюс еще ENO файл скачал на него "E5_ENO_WK2012_v034".
Добавлено через 12 минут
Вот получилось вроде прошить,гляньте лог:
Код:
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm632_Substrate_test_10w14_v5.1_PRD.cmt
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Transmission type request fail [000000]
-> Boot error... :(
-> Boot fail...
Flashing failed...
Phone disconected!
Connect phone on selected interface...
Core : v1.98 , BB5XG FlashEngine : v9.9
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...
Files Set for Flashing :
MCU : rm632_Substrate_test_10w14_v5.1_PRD.cmt
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode
Backup enabled, will read all certificates...
Reading NPC certificate...
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
- > No any CRT data (MCU damaged/CERT erased), skip saving
=== SW Version Check ===
- > Can not collect initial info, continue flashing...
- > Hope, this version will be ok
=== SW Version Check ===
===Flashing [MCU]===
Erase : Processing rm632_Substrate_test_10w14_v5.1_PRD.cmt
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm632_Substrate_test_10w14_v5.1_PRD.cmt
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [SOS*ISASW]
Total writen 17 blocks
TIME : Write time : 00:00:00
MCU Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000
ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot
Flashing done!
Total flash time : 00:00:00
Reboot phone now...
- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy