Re: Не могу влить Rom1
#7
Тоже наткнулся с подобной проблемой. Huawei P6-U06 висит на логотипе, снимал emmc, подключил к easy jtag с адаптером от e-mate. Сливал 8 гиг fullflash.
Флешка SanDisk SD5C26A-8G.
Цитата:
Z3X EasyJtag Software ver. 1.9.0.5
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1577 mV
Output file :E:\Z3X\pinout\Huawei P6-U06\Копия\EMMC_ROM1_00000000_200000000.bin
Reading 0x000200000000 bytes from 0x000000000000 ...ROM1 ( USER ROM)
Read Length has been corrected to 0x0001D9800000 bytes...
Done. Read Speed: 636 kB/s
|
Далее есть слитый Rom1 с другой ТА 512 и 2 гиг, хотел пролить и того ошибка.
Цитата:
Z3X EasyJtag Software ver. 1.9.0.5
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1577 mV
Input file : E:\Z3X\pinout\Huawei P6-U06\P6\EMMC_ROM1_00000000_80000000.bin
Writing 0080000000 bytes to 00000000 ...ROM1 (USER ROM)
Write Block Failed, Reason: Write Block Verify Error
Done.
|
Пробовал пролить слитый fullflash, прошивается.
Цитата:
Z3X EasyJtag Software ver. 1.9.0.5
Skip loading eMMC Addon Firmware
CMD Pullup Level:1103 mV
CMD Active Level:1577 mV
Input file : E:\Z3X\pinout\Huawei P6-U06\Копия\EMMC_ROM1_00000000_200000000.bin
Writing 01D9800000 bytes to 00000000 ...ROM1 (USER ROM)
Writing flash page stopped by user request
Done.
|
Далее, стирал полностью rom1.
Цитата:
Z3X EasyJtag Software ver. 1.9.0.5
Skip loading eMMC Addon Firmware
CMD Pullup Level:1113 mV
CMD Active Level:1588 mV
Erasing 200000000 bytes from 00000000 ...ROM1
Erase Length has been corrected to 0x0001D9800000 bytes...
Erase Done.
|
Теперь не прошивается ни какой файл.
Цитата:
Z3X EasyJtag Software ver. 1.9.0.5
Skip loading eMMC Addon Firmware
CMD Pullup Level:1113 mV
CMD Active Level:1588 mV
Input file : E:\Z3X\pinout\Huawei P6-U06\P6\EMMC_ROM1_00000000_80000000.bin
Writing 0080000000 bytes to 00000000 ...ROM1 (USER ROM)
Retry writing adress 0x00000000 (Attempt #1)...
Retry Fail!
Retry writing adress 0x00000000 (Attempt #2)...
Retry Fail!
Retry writing adress 0x00000000 (Attempt #3)...
Retry Fail!
Write Block Failed, Reason: DATA SND CRC Error
Done.
|
Check проходит нормально.
Цитата:
CMD Pullup Level:2196 mV
CMD Active Level:2670 mV
eMMC Device Information
EMMC CID : 45010053454D30384790822A098130AC
EMMC CSD : D00F00320F5903FFFFFFFFFF92404010
EMMC Manufacturer ID: 0045 , OEM ID: 0100
EMMC Date: 03/2013 Rev.0x90
EMMC NAME: <b>SEM08G</b> , S/N: 2183793025
EMMC NAME (HEX): 53454D30384700
EMMC ROM1 (Main User Data) Capacity: 7576 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x02 , width 8bits , Partition config [179]: 0x08.
Backup saved: SEM08G_2183793025_20150302_1726.extcsd
Done.
|
Вопрос, в чем проблема, в адаптере или все таки дохлая флешка?