Flashing firmware from F:/GSM/LG/P760/LGP760AT-00-V20h-EUR-YYY-JUL-12-2013+0_AP_CP.sbf
Disconnect the cable from the handset, remove accumulator, wait five seconds and insert the cable into the handset
The hanset should go into download mode. If it has not happen ant the handset has started booting in normal mode repeate the action
Device found
sending preloader
sending ebl
Setting baud rate
Flashing partition NAND_ID_PSI_IMAGE
Flashing partition NAND_ID_SLB_IMAGE
Flashing partition NAND_ID_DSP_IMAGE
Flashing partition NAND_ID_CODE_IMAGE
data port: I/O error:

LG 2-3G Tool v4.9
Поддерживаемые модели: 849

Open port COM9... OK
GetIMEI... Ошибка
Прошедшее: 0 сек --> (v4.9)

Plug USB cable
wait 4 seconds and put battery back in.
waiting for OMAP44xx device...

Device descriptor:
        bLength            = 18
        bDescriptorType    = 1
        bcdUSB             = 528
        bDeviceClass       = 255
        bDeviceSubClass    = 255
        bDeviceProtocol    = 255
        bMaxPacketSize0    = 64
        idVendor           = 451
        idProduct          = D00F
        bcdDevice          = 0
        iManufacturer      = 33
        iProduct           = 37
        iSerialNumber      = 0
        bNumConfigurations = 1
reading ASIC ID
usb_write 4
usb_read 81[*] read 0 bytes
NumOfSubblocks: 0x5
Subblock ID: 0x1
Subblock Size: 0x5
CH enabled: 0x7
ROM revision: 0x4
Checksum Subblock: 0x15
CHIP: 4430
IDEN: 487c733ad1f2b45968bdb830ab0696e3461c5822
MPKH: 5f4092eccddf90fa43f546adf89508b31b9c74795e9516194c0ea6412fdcb7f6
CRC0: 9c669ad9
CRC1: 682adccf
sending 2ndstage to target... f0030002
usb_write 4
usb_write 4

wait 5-lelelel...
[*] msg size = 4
usb_write 21552[*] data size = 21552
usb_close

Reopen usb...


Device descriptor:
        bLength            = 18
        bDescriptorType    = 1
        bcdUSB             = 528
        bDeviceClass       = 255
        bDeviceSubClass    = 255
        bDeviceProtocol    = 255
        bMaxPacketSize0    = 64
        idVendor           = 451
        idProduct          = D00F
        bcdDevice          = 0
        iManufacturer      = 33
        iProduct           = 37
        iSerialNumber      = 0
        bNumConfigurations = 1
waiting for 2ndstage response...
usb_read 4
usb read = aabbccdd
accepted 2ndstage response
sending image to target...
size = 246272
usb_write 4
usb_write 246272
 ** Done **
< waiting for device >
sending 'x-loader' (384 KB)...
OKAY [  0.200s]
writing 'x-loader'...
FAILED (remote: partition does not exist)
finished. total time: 0.208s
sending 'u-boot' (1024 KB)...
OKAY [  0.527s]
writing 'u-boot'...
FAILED (remote: partition does not exist)
finished. total time: 0.532s
Done