Re: Не удается восстановить Samsung S7250D
#15
Цитата:
Сообщение от Nics
мысль отвлеченная, но все же.. а нет ли у этой модели таких же моментов, как у S5230? (ревизии PCB имеются ввиду с разными Flash IC )?
|
Думаю что нет.
Как RIFF видит ТА после стирания Medusa и попыток прошить ему boot область.
Развернуть для просмотра
[02.11.2013 11:01:06] [START OPERATION_ID = RESURRECT]
[02.11.2013 11:01:38] Open serial port...OK
[02.11.2013 11:01:38] Connecting to the RIFF Box...OK
[02.11.2013 11:01:38] Firmware Version: 1.37, JTAG Manager Version: 1.54
[02.11.2013 11:01:38] Selected Resurrector: [Samsung S7250D V1.0.4660.65212]
[02.11.2013 11:01:38]
[02.11.2013 11:01:38] Connecting to the dead body...OK
[02.11.2013 11:01:38] Detected dead body ID: 0x07B3617F - CORRECT!
[02.11.2013 11:01:38] Set I/O Voltage reads as 3.01V, TCK Frequency is 4 MHz
[02.11.2013 11:01:38]
[02.11.2013 11:01:38] Resurrection sequence started.
[02.11.2013 11:01:38] Establish communication with the phone...OK
[02.11.2013 11:01:38] Initializing internal hardware configuration...OK
[02.11.2013 11:01:38] Uploading resurrector data into memory...OK
[02.11.2013 11:01:38] Starting communication with resurrector...OK
[02.11.2013 11:01:38]
[02.11.2013 11:01:38] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
[02.11.2013 11:01:38] Selected Resurrection Data for the NAND Chip with Page size = 4KB
[02.11.2013 11:01:38]
[02.11.2013 11:01:38] Flashing the dead body...OK
[02.11.2013 11:01:38] Resurrection complete!
[02.11.2013 11:01:38] [FINISH OPERATION_ID = RESURRECT]
[свернуть]
В boot не входит. Да есть подозрение что RIFF не правильно стирает flash. Или же режет размер.
Да и еще при resurrection пишет запись виртуального адресса.
Пролил full без стирания. Реакция та же.
Развернуть для просмотра
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.55
Selected Resurrector: [Samsung S7250D V1.0.4660.65212]
Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 3.01V, TCK Frequency is 4 MHz
Settings Code: 0x34010900000000000000000020000000
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x0050 (512MB)
Resuming write FLASH1 memory from 0x000000000000 to 0x00001FFFFFFF on 0x000000000000
WARNING: Programming Error (0x24) at 0x000017B40000 is Ignored.
Completed in 00:32:33.109 (Average Transfer Rate: 276.83 kB/s)
[свернуть]
Лог после очередного стирания RIFF:
Развернуть для просмотра
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.55
Selected Resurrector: [Samsung S7250D V1.0.4660.65212]
Connecting to the dead body...OK
Detected dead body ID: 0x07B3617F - CORRECT!
Set I/O Voltage reads as 3.01V, TCK Frequency is 4 MHz
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip, ID: 0x0000/0xFFFF
Selected Resurrection Data for the NAND Chip with Page size = 4KB
Flashing the dead body...
ERROR: DCC Loader has reported Error Code = 0x30 (0x000000). Trying to recover...FAILED
ERROR: Failed due to multiple communication errors. Terminating at 0x000000000000
[свернуть]