Init Service mode... Wait...

-> Infineon XG110 : IMEI Backup Created
Connect phone on selected interface...

Phone found!
Series 40 Device detected! 
read info...  - Ok

Reading Phone Info....
SW ver  : V 03.91 17-05-12 RH-130 (c) Nokia
IMEI    :      353253058492966
PPM     :      V 03.91
17-05-12
RH-130
(c) Nokia
AE
PCode   :      059H2D2
BPCode  :      059P8T9
HWID    :      3051
LCDVer  :      WIN:BARACOAv95
NT39121
IMEI    :      353253058492966
Sl Conf  : 001-01-00000000000
Sl Prof  : 000000000004000-2
Sl Aux   : 000B0000
Hw Sig   : 257AB75F4F3DF102
Country      : Test SIM (Open)
Operator     : NOKIA (Open)

Lock info:
Block 1
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 2
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 3
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 4
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 5
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 6
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 7
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  

Done!

Core : v1.60 , BB5XG FlashEngine : v3.9

Selected FlashSettings : FullFlash
Files Set for Flashing :
MCU : rh130_003.910
PPM : rh130_003.91ek
CNT : rh1300_nai03.91ek

Infineon flashing...
-> Infineon XG110 : IMEI Backup Created
Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
PBL : Dynamic
Boot Ok , 01AB
SBL : Dynamic
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 00EC0000007A2200
FLASH ID : UNKNOW [Not In Base]
Boot Done!

   ===Flashing [MCU]===
File : rh130_003.910
Image : hw_f31_rh130_r03.910.fls
Cert block found, sending....
Cert sent
Found 3 region(s)
Processing Region 1/3
Erase , Start : 0x00800000 , Len : 0x00210000
Erasing, wait ... 
Erase done
Write , Start : 0x00800000 , Len : 0x00210000
Flashing , wait ...
Region flash done
Processing Region 2/3
Erase , Start : 0x00C60000 , Len : 0x00250000
Erasing, wait ... 
Erase done
Write , Start : 0x00C60000 , Len : 0x0021BC80
Flashing , wait ...
Region flash done
Processing Region 3/3
Erase , Start : 0x00FFC000 , Len : 0x00004000
Erasing, wait ... 
Erase done
Write , Start : 0x00FFC000 , Len : 0x00000040
Flashing , wait ...
Region flash done
Check : C9E0
   ===Flashing [PPM]===
File : rh130_003.91ek
Image : hw_f31_rh130_003.91ek.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00210000 , Len : 0x00250000
Erasing, wait ... 
Erase done
Write , Start : 0x00210000 , Len : 0x00207000
Flashing , wait ...
Region flash done
Check : 6F5C
   ===Flashing [CNT]===
File : rh1300_nai03.91ek
Image : hw_f31_rh1300_nai03.91ek.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00EB0000 , Len : 0x000D0000
Erasing, wait ... 
Erase done
Write , Start : 0x00EB0000 , Len : 0x000503C0
Flashing , wait ...
Region flash done
Check : A1D9

Flashing done, rebooting...
-> Infineon info : Do FullFactory Sets after flashing
Flashing Done!