port COM2 open OK 
Connect phone on selected interface...

Selected FlashSettings : Manual
Files Set for Flashing :
MCU : rm653_006.200
PPM : rm653_006.20ej
CNT : rm6530_nai06.20ej

Infineon flashing...
Booting phone now....
Phone must be POWER OFF
Insert Cable or Press PowerON Button!
Sync Ok , A2
CPU ID : XGOLD , A200341100
Boot Ok , 01
PBL : SE0_091125  F11
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000C08800
FLASH ID : ST, M58WR064
Boot Done!

   ===Flashing [MCU]===
File : rm653_006.200
Image : hw_b2_rm653_r06.200.fls
Cert block found, sending....
Cert sent
Found 3 region(s)
Processing Region 1/3
Erase , Start : 0x00800000 , Len : 0x00210000
Erasing, wait ... 
Erase done
Write , Start : 0x00800000 , Len : 0x00210000
Flashing , wait ...
Region flash done
Processing Region 2/3
Erase , Start : 0x00C60000 , Len : 0x0020A0C0
Erasing, wait ... 
Erase done
Write , Start : 0x00C60000 , Len : 0x0020A0C0
Flashing , wait ...
Region flash done
Processing Region 3/3
Erase , Start : 0x00FFC000 , Len : 0x00000040
Erasing, wait ... 
Erase done
Write , Start : 0x00FFC000 , Len : 0x00000040
Flashing , wait ...
Region flash done
Check : 7CCF
   ===Flashing [PPM]===
File : rm653_006.20ej
Image : hw_b2_rm653_006.20ej.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00210000 , Len : 0x001F6FC0
Erasing, wait ... 
Erase done
Write , Start : 0x00210000 , Len : 0x001F6FC0
Flashing , wait ...
Region flash done
Check : 4BA9
   ===Flashing [CNT]===
File : rm6530_nai06.20ej
Image : hw_b2_rm6530_nai06.20ej.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00EB0000 , Len : 0x00060580
Erasing, wait ... 
Erase done
Write , Start : 0x00EB0000 , Len : 0x00060580
Flashing , wait ...
Region flash done
Check : CC7E

Flashing done, rebooting...
-> Infineon info : Do FullFactory Sets after flashing
-> Infineon info : If phone not connect automatically after flash : 
-> Infineon info : Reinsert cabel, PowerUp phone and do Factorysets
Flashing Done!

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info...  - Ok

Reading Phone Info....
SW ver  : V 06.20 01-12-10 RM-653 (c) Nokia
IMEI    :      353775045342789
PPM     :      V 06.20
01-12-10
RM-653
(c) Nokia
EJ
PCode   :      0587415
BPCode  :      059B9S2
HWID    :      1002
LCDVer  :      TPO:BOHAIv80
HX5081
IMEI    :      353775045342789
Sl Conf  : 001-01-00000000000
Sl Prof  : 000000000003000-2
Sl Aux   : 000B0000
Hw Sig   : 635FDD664C3B21AE
Provider : Default Test Operator

Lock info:
Block 1
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 2
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 3
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 4
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 5
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 6
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  
Block 7
L1:Open;  L2:Open;  L3:Open;  L4:Open;  L5:Open;  

Done!

Read and Check phone data...
Infineon checking...

SIMLOCK TEST : Ok
RUN TEST     : Ok

Done!

Resetting selected items...
Check phone mode...
Phone in Normal mode
Seting Test mode... wait...
Test mode set
Settings Full Factory Defaults...
Set OK!
Settings Software Upgrade Defaults...
Set OK!
Settings Service Centre Defaults...
Set OK!
Settings Production Tune Defaults...
Set OK!
Settings User Data Defaults...
Set OK!
Settings Leave Factory defaults...
Set OK!

Elapsed: 00:00:22

Phone disconected!