COM9 [Serial3] selected
module  v3.15
Device: Autodetect 6228-6239 NAND
Checking data, wait...
Action: write flash NAND
write: Firmware
E710_PXHT2ADX10_PCB01_GPRS_MT6235B_S01.01_0__firmware_355981035135948.B4M.bin
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
nfi area detection...
converting data...
done 0x02E8C000 bytes
external bootloader is not present
bootloader version: E710_BOOTLOADER_V005_MT6235B_01_1.bin
nfi area detection finished: Ok
interface: BROM_DLL_v3.1012.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6235:8A04:8A01
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[0058]: 002C:00A100800015 [MICRON] MT29F1G08ABB
chip size: 128Mb
page/spare size: 0800/0040
pages per block: 0040
bits i/o: 08
address cycles: 04
internal RAM size: 00010000
external RAM: S_DA_RAM_ERROR
done
Set baudrate (921600)...
done
ram test...
testing...
ram test passed
===>  detect existing firmware structure...
detect ffs...
ffs offset/size: 03000000/05000000
firmware size: 48Mb
ffs size: 80Mb
detect sec ro...
detect custom parameters...
detect project-id...
project-id: E710_PXHT1ADX10.01.0
detect NAND info...
number of areas/bytes to read: 1:001A0000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
warning: core offset is not detected
nfi area detection finished: failed
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
startup code area #1 detection done
rom info ver: 05
sw version: E710_PXHT1ADX10_PCB01_GPRS_MT6235B_S01.01_0.BIN
project-id: E710_PXHT1ADX10.01.0, 00000000
code offset: 00000000
ffs offset/size [01]: 03000000/05000000
rom info structure: 2nd [standard] generation
TCL-ID is absent
===>  done
====================
New firmware detected (v.3.15, database date: 14.06.2010): 
E710_PXHT1ADX10_PCB01_GPRS_MT6235B_S01.01_0.BIN

This firmware is missing in support area. If this phone is good and working:

- download latest software from support area and try again, probably this firmware already supported in latest software
- make "Read full flash" operation
- send flash backup files to support: [email protected] or upload files to http://rapidshare.com or http://4shared.com
- include in your e-mail full text from phone back label (phone name etc.)
====================
nfi area detection...
converting data...
done 0x02E8C000 bytes
external bootloader is not present
bootloader version: E710_BOOTLOADER_V005_MT6235B_01_1.bin
nfi area detection finished: Ok
startup code area #1 check...
startup code area #1 fixed
number of cores: 3
loading files...
number of areas: 3
done
write...
write bootloader...
.
.
write core...
Disconnect...
done
Finished, time used: 10 min 27 sec
Remove/Install battery now !