Re: Пожелания и рекомендации команде Infinity Box
#454
Пришел на разблокировку Philips X800. Запускаю Shell. выбираю в нём эту модель запускаю через Shell MModule. MModule 2.84 запускается с выбранной моделью Fly-LX800. Далее вручную выбираю свою модель и пробую прочитать фулл. Вот лог:
Код:
COM2 [VCP8] selected
module v2.84
Device: Philips-X800
Checking data, wait...
Action: read NAND flash
read mode: 01
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6229:8A02:8A02]...
CPU: MT6229
chip: 0031:0003:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.02
cpu-id: 09
loader: 3.0840.00.00
NAND id: AD79A500
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 2000
external ram: 00000000
finalize connection...
done
emi configuration...
ram size: 04000000
emi configuration done
ram test...
pass 1...
pass 2...
pass 3...
pass 4...
done
NOR: 0000:000000000000 [00000000]
NAND: 00AD:007900A50000 [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
921600
Set baud Done
Identification ...
ram test...
pass 1...
pass 2...
pass 3...
pass 4...
done
reading bootloader structure area (00010000 bytes)...
detecting bootloader structure...
source data: page only
rom info protocol ver: 04
ver. sw 1: NOLLEC29_07A_PMJ_PCB03_GPRS_MT6229_S02.X800_M6229X_RUSSIA_V11.BIN
ver. sw 2: X800_M6229X_RUSSIA_V11, E3CFCDF6
ffs offset/size: 04000000/04000000
id-page1 Ok
На последней строке вылетает ошибка Range check error и MModule зависает с единственной активной кнопкой Stop
С выбранной моделью Fly-LX800 естественно ничего не получилось:
Код:
COM2 [VCP8] selected
module v2.84
Device: Fly-LX800
Checking data, wait...
advanced flash detection enabled
Action: read NOR flash
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6229:8A02:8A02]...
CPU: MT6229
chip: 0031:0003:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 90009000900090:90909000000000
flash: 90009000900090:90909000000000
number of flash chip/regions detected: 00/01
flash chip is unknown or damaged, operation aborted.
Fault reasons:
1. unknown hardware: contact to support: [email protected]
2. hardware is damaged: check hardware, water inside etc.
Initialize Fail
Finished, time used: 11 sec
Remove/Install battery now !
Аппарат уже ушел, разблокировался удачно
Сейчас занимаюсь еще одним аппаратом с таким фуллом - APL228_PCB03_GPRS_MT6230_S02.APL228_TOSHIBA_3P_R_0 90626_V2_4
Лог ChineseMiracle 2.89:
Код:
COM2 [VCP2] selected
module v2.89
Device: Autodetect 6228-6230 NAND
Checking data, wait...
Action: read NAND firmware
read mode: 01
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6230:8A02:8A02]...
CPU: MT6230
high speed boot On
chip: 0031:000B:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.02
cpu-id: 0C
loader: 3.0840.00.00
NAND id: EC795A3F
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 2000
external ram: 00000000
finalize connection...
done
emi configuration...
ram size: 04000000
emi configuration done
ram test...
pass 1...
pass 2...
pass 3...
pass 4...
done
NOR: 0000:000000000000 [00000000]
NAND: 00EC:0079005A003F [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
921600
Set baud Done
Identification ...
ram test...
pass 1...
pass 2...
pass 3...
pass 4...
done
reading bootloader structure area (00010000 bytes)...
detecting bootloader structure...
source data: page only
id-page1 Ok
Также вылетает ошибка Range check error. При этом версия 2.87 хоть и говорит, что прошивка её неизвестна, но читает её. Что делать? Ждать нового релиза или можно записывать этот бэкап версией 2.87? Считываю фулл для русификации