COM4 selected
module  v2.75
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: write NOR flash
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
ffs/eeprom backup enabled, it may takes several minutes !
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A03:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:FF0F:FFFF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
detecting chip #00 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #02 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #03 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 04/01
Initialize Done
Set baud ...
460800
Set baud Done
Initialize bootcode ...
Initialize bootcode Done
Check firmware integrity ...
device parameters autodetection in progress...
detecting chip #00 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
detecting chip #01 in region #00...
flash: 04227E22212200:18E59F00000000
flash: Fujitsu AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification#1...
detection phase #1...
detect device identification#1 finished
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
identification#1 protocol ver: 04
ver. sw 1: MT25_06B_HW.DS100_RU2_V3_2BTEST--080627.BIN
ver. sw 2: DS100_RU2_V3.2BTEST, 00000000
ffs offset/size: 00E00000/00200000
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset detected: 00E00000
flash: 04227E22212200:18E59F00000000
checking area [00000000]: 00000000-00FFFFFF...
ffs/eeprom found near: 00E00000
detecting ffs/eeprom size...
ffs/eeprom size: 00200000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:00E00000-00FFFFFF
Check firmware integrity Done
Check firmware content ...
Check firmware content Done
Backup required data ...
reading: eeprom[MT25_06B_HW.DS100_RU2_V3_2BTEST--080627.BIN]...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\eeprom[MT25_06B_HW.DS100_RU2_V3_2BTEST--080627.BIN]_20090129-104030.B0E.bin
flash: 04227E22212200:18E59F00000000
Backup required data Done
Patch required data ...
Patch required data Done
Special operation ...
Special operation Done
Write ...
detect device identification#2...
detection phase #1...
.
detect device identification#2 finished
detecting security area (code #2)...
security area (code #2) is absent
Area: Firmware
flash: 04227E22212200:18E59F00000000
Write: Firmware
error: no any expected answer
error: flash write error: 00800000:00002000
detect device identification#2...
detection phase #1...
error: unexpected termination/freez: 00000000
detect device identification#2 finished
Write Fail
Finished, time used: 726 sec
Remove/Install battery now !