COM12 [Serial2] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: write NAND flash
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page+spare
converting data...
done 0x03E0FA00 bytes
identification#1 protocol ver: 04
ver. sw1: K2_PCB04_GPRS_MT6228_S02.G30V01_01B05.BIN
ver. sw2: G30v01.01b05, 7186BF55
ffs offset/size: 02000000/02000000
id-page1 Ok
warning: ffs size mismatch: 01E0FA00/02000000
nfi area detection finished: Ok
Boot...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
high speed boot enabled
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND id: EC76A5BD
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 1000
ram size: 00800000
NOR:  0000:000000000000 [00000000]
NAND: 00EC:007600A500BD [04200000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Initialize bootcode...
reading structure area...
detecting structure...
source data: page+spare
converting data...
done 0x00010000 bytes
identification#1 protocol ver: 04
ver. sw1: K2_PCB04_GPRS_MT6228_S02.BC08V01_01B04.BIN
ver. sw2: BC08v01.01b04, 4CB4305E
ffs offset/size: 02000000/02000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area#1 is Ok
security area#1 backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.27EADFDB.[K2_PCB04_GPRS_MT6228_S02.BC08V01_01B04.BIN_A1CF4BB3].rpl
identification#1 detection finished
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.27EADFDB.[K2_PCB04_GPRS_MT6228_S02.G30V01_01B05.BIN_AA40798E].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.27EADFDB._K2_PCB04_GPRS_MT6228_S02.G30V01_01B05.BIN_AA40798E_.rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.27EADFDB.[K2_PCB04_GPRS_MT6228_S02.G30V01_01B05.BIN_AA40798E].rpl
warning: rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.27EADFDB._K2_PCB04_GPRS_MT6228_S02.G30V01_01B05.BIN_AA40798E_.rpl
====================
warning: unknown identification#1 structure: K2_PCB04_GPRS_MT6228_S02.G30V01_01B05.BIN_AA40798E
error: Unknown firmware, user action required:
1. download latest software from support area and try again !
2. if no still luck follow the next procedure:
- find good working phone with the same firmware:
  K2_PCB04_GPRS_MT6228_S02.G30V01_01B05.BIN
- make "Read detailed information" operation
- send "backup_system_log_..." file to support: [email protected]
- make "Read full flash" operation
- send flash backup file(s) to support: [email protected]
- include in your e-mail full text from phone back label (phone name etc.)
- be little bit patient and wait update
====================
You can flash phone now but can't finalize it.
In most cases phone can NOT power-on normally.
Do you want to write flash anyway ?
Initialize bootcode Done
Check firmware integrity...
Check firmware integrity Done
Check firmware content...
Check firmware content Done
Backup required data...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log_27EADFDB_K2_PCB04_GPRS_MT6228_S02.BC08V01_01B04.BIN_A1CF4BB3_20080513-231825.B4X.bin
write core area 1 of 2...
write core area 2 of 2...
Backup required data Done
Patch required data...
Patch required data Fail
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_system_log_27EADFDB_K2_PCB04_GPRS_MT6228_S02.BC08V01_01B04.BIN_A1CF4BB3_20080513-232330.B4X.bin
Finished, time used: 454 sec
Remove/Install battery now !