Тема: Помогите решить проблему с СИМ2 на китайских телефонах.
Показать сообщение отдельно
  • Новое
    Аватар для Gavs

    Gavs
    Участник
    Действительный участник ассоциации MCRF.RU

    Сообщений:
    97
    Регистрация:
    11.07.2006
    Возраст:
    53
    Рейтинг мнений:
    Вес репутации: 233
    Gavs Gavs
    Очки: 8,584, Уровень: 62 Очки: 8,584, Уровень: 62 Очки: 8,584, Уровень: 62
    Активность: 8% Активность: 8% Активность: 8%
    По умолчанию Re: Помогите решить проблему с СИМ2 на китайских телефонах. #9
    Цитата:
    Сообщение от AVL Посмотреть сообщение
    то перелейте софт под 6205 (версию этой прошивки вы ,кстати, не указали)
    Версия прошивки под второй проц не понятна, пытался вычитывать на разных портах с разной скоростью, выкладываю лог Infinity:
    Цитата:
    COM1 selected
    Device: Autodetect 6205-6227 NOR
    Checking data, wait...
    advanced flash detection enabled
    Action: read eeprom
    Boot...
    Press and HOLD Power button now !
    baud autodetection active
    19200
    Connecting, wait...
    Initializing[6205:8B00]...
    CPU: MT6205
    boot step size: 0400
    Release Power button now !
    Boot Done
    Initialize...
    detecting chip #00 in region #00...
    flash: BF7353FFFF0052:18E59F00000000
    warning: detected/calculated [00400000/00800000] chip size mismatch, chip detection error
    flash: SST AMD/Fujitsu std [def 0040x010000 0400x001000] 8Mb
    detecting chip #01 in region #00...
    flash: BF7353FFFF0052:18E59F00000000
    warning: detected/calculated [00400000/00800000] chip size mismatch, chip detection error
    flash: SST AMD/Fujitsu std [def 0040x010000 0400x001000] 8Mb
    detecting chip #02 in region #00...
    flash: BF7353FFFF0052:18E59F00000000
    warning: detected/calculated [00400000/00800000] chip size mismatch, chip detection error
    flash: SST AMD/Fujitsu std [def 0040x010000 0400x001000] 8Mb
    detecting chip #03 in region #00...
    flash: BF7353FFFF0052:18E59F00000000
    warning: detected/calculated [00400000/00800000] chip size mismatch, chip detection error
    flash: SST AMD/Fujitsu std [def 0040x010000 0400x001000] 8Mb
    number of flash chip/regions detected: 04/01
    Initialize Done
    Set baud...
    115200
    Set baud Done
    Identification...
    device parameters autodetection in progress..
    detecting chip #00 in region #00...
    flash: BF7353FFFF0052:18E59F00000000
    warning: detected/calculated [00400000/00800000] chip size mismatch, chip detection error
    flash: SST AMD/Fujitsu std [def 0040x010000 0400x001000] 8Mb
    detecting chip #01 in region #00...
    flash: BF7353FFFF0052:18E59F00000000
    warning: detected/calculated [00400000/00800000] chip size mismatch, chip detection error
    flash: SST AMD/Fujitsu std [def 0040x010000 0400x001000] 8Mb
    it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
    number of flash chip/regions detected: 01/01
    total flash region size: 00800000
    detect device identification#1...
    detection phase #1...
    .
    detection phase #2...
    .................................................. .................................................. ............................
    warning: identification#1 information not found, possible reasons:
    .old firmware type w/o identification#1 data
    .damaged firmware
    .damaged hardware
    if phone works fine just ignore this warning
    detect device identification#1 finished
    detect device identification#2...
    detection phase #1...
    .
    warning: optional information not found
    detect device identification#2 finished
    detecting eeprom/ffs area in 1 chip(s)...
    standard eeprom/ffs offset assigned: 00700000
    flash: BF7353FFFF0052:18E59F00000000
    warning: detected/calculated [00400000/00800000] chip size mismatch, chip detection error
    checking area[00000000]: 00000000-007FFFFF...
    eeprom/ffs found near: 00300000
    Detected eeprom/ffs address is non-standard: 00300000

    Posible reasons:
    1. eeprom is Ok but address is non-standard
    2. eeprom damaged and can't be detected
    3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)

    If you are not sure that detected address is correct:
    1. press "NO" (and select standard address or terminate current operation)
    2. make flash backup for emergency case
    3. repeat required operation

    Are you sure that detected eeprom address is correct ?
    autodetected eeprom/ffs address[00300000] confirmed by user
    detecting eeprom/ffs size...
    eeprom/ffs size: 00500000
    ffs chip: 00
    eeprom/ffs area: 00000000:00300000-007FFFFF
    reading [eeprom]...
    file saved: D:\Infinity\FlashFiles_ChineseMiracle\Cect K808\backup_eeprom_20080429-170312.B0E.bin
    Finished, time used: 592 sec
    Remove/Install battery now !

    Последний раз редактировалось Gavs; 30.04.2008 в 10:04.
    30.04.2008, 10:03
    Меню пользователя Gavs
    Посмотреть профиль
    Отправить личное сообщение для Gavs
    Найти ещё сообщения от Gavs
    Файловый архив
    Скачиваний: (6) 713.02 Мб