MobilaGSM
19.07.2016, 12:36
Пришел данный ТА после обновления через WiFi уходит в цикличный ребут на оптимизации приложений Android.
Wipe через Recovery, Format / Reset Setting через СМ2МТК не помогает.
Скачал прошивку (http://gsmforum.su/showpost.php?p=505198&postcount=502) слитую с данного ТА с помощью СМ2МТК.
Прошилось без ошибок, но по факту не включающийся аппарат. Коннектится исправно.
Chinese Miracle II [MTK module] v 1.51
Scatter Load Ok , BaseBand : MT6580 , Project : d5 , Storage : EMMC
Files found : 10 , Set to Flash : 9
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : lge
Device Model : m13g
Device CPU : MT6580
Device IntName : m13g_global_com
Device Version : 5.1
Device Compile : 03.02.2016 11:44:25
Device Project : ALPS.L1.MP6.V2.19_ARIMA6580.WE.L_P37
Device ExtInfo : LG-X210
Ready to Flash!
Operation : Flash [ v1.51 ]
======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D4200E52E9B702319
Initialize Memory ...
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x40000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D4200E52E9B702319
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x64362B44E71AAB32D6C42E663D492E45
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
ScatCFG : BaseBand : MT6580 , Project : d5 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled
Switching to HSUSB
HSUSB Init Ok
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!
BL : BatteryLevel : 4148 mV
BL : BatteryLevel Ok
BL : Flash Pre-Erase
Total blocks to Erase : 3
Erase : 0x0000000001C80000-0x0000000023340000
Erase : 0x00000000250C0000-0x0000000005740000
Erase : 0x000000002B000000-0x00000001A5F80000
Flash Pre-Erase Done, time used : 00:00:13
SecCfg Passed , 179A
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_d5.bin
Preloader Sent , Init passed
SecCfg Passed , 179A
PartCount : 0016
Update PMT by user request
Repartition Done!
Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : FLEX
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:08:40
Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : FLEX
Verify Passed : SECRO
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:00:03
Update Mirror PMT
Update Done!
Update RomInfo done
Done!
Elapsed: 00:09:18
Reconnect Power/Cable!
После прошивки делал Format / Reset Setting, но результат нулевой.
p.s. Пробовал Прошить FlashTool 'м от X135/145 - программа ругается на не верный scatter.
Слил с рабочего ТА полный FullFlash ? залил в подопытного - ситуация на месте, аппарат не подает признаков жизни, потребление при нажатии на PWR около 70 ма, немного потом падает и опять возвращается к 70мА.
Wipe через Recovery, Format / Reset Setting через СМ2МТК не помогает.
Скачал прошивку (http://gsmforum.su/showpost.php?p=505198&postcount=502) слитую с данного ТА с помощью СМ2МТК.
Прошилось без ошибок, но по факту не включающийся аппарат. Коннектится исправно.
Chinese Miracle II [MTK module] v 1.51
Scatter Load Ok , BaseBand : MT6580 , Project : d5 , Storage : EMMC
Files found : 10 , Set to Flash : 9
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : lge
Device Model : m13g
Device CPU : MT6580
Device IntName : m13g_global_com
Device Version : 5.1
Device Compile : 03.02.2016 11:44:25
Device Project : ALPS.L1.MP6.V2.19_ARIMA6580.WE.L_P37
Device ExtInfo : LG-X210
Ready to Flash!
Operation : Flash [ v1.51 ]
======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use SecMode DA
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 150100513732534D4200E52E9B702319
Initialize Memory ...
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x40000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMS27
[eMMC] : FLASH_CID : 150100513732534D4200E52E9B702319
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
DEV RID : 0x64362B44E71AAB32D6C42E663D492E45
INT RAM : 0x00020000
EXT RAM : 0x40000000 [1 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
ScatCFG : BaseBand : MT6580 , Project : d5 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled
Switching to HSUSB
HSUSB Init Ok
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!
BL : BatteryLevel : 4148 mV
BL : BatteryLevel Ok
BL : Flash Pre-Erase
Total blocks to Erase : 3
Erase : 0x0000000001C80000-0x0000000023340000
Erase : 0x00000000250C0000-0x0000000005740000
Erase : 0x000000002B000000-0x00000001A5F80000
Flash Pre-Erase Done, time used : 00:00:13
SecCfg Passed , 179A
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_d5.bin
Preloader Sent , Init passed
SecCfg Passed , 179A
PartCount : 0016
Update PMT by user request
Repartition Done!
Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : FLEX
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:08:40
Processing : Verify
Verify Passed : LK
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : LOGO
Verify Passed : FLEX
Verify Passed : SECRO
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:00:03
Update Mirror PMT
Update Done!
Update RomInfo done
Done!
Elapsed: 00:09:18
Reconnect Power/Cable!
После прошивки делал Format / Reset Setting, но результат нулевой.
p.s. Пробовал Прошить FlashTool 'м от X135/145 - программа ругается на не верный scatter.
Слил с рабочего ТА полный FullFlash ? залил в подопытного - ситуация на месте, аппарат не подает признаков жизни, потребление при нажатии на PWR около 70 ма, немного потом падает и опять возвращается к 70мА.