AlexeyMadjar
14.12.2012, 10:15
Аппарат пришел с признаками ПО - сильно тормозил. Был еще косяк - не видел SIM. Была 20-я версия. Клиент попросил обновить. Прошил BEST'ом 40-ю, с wipe. Итог - висит на заставке NOKIA.
Лог:
==========
FW APE version : 20.2011.40-4
FW PRx release : PR_1.1
FW Region info : EUROPE [1] , America (Latin , South), South Africa
FW Region ver : 001
==========
Read info Ok
=== SW version Check ====
Ok [Reflashing or Upgrade]
=== SW version Check ====
Processing APE Boot...
File : DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_001-OEM1-958_ARM.bin
Processing : ape-algo
APE Algorithm boot Ok
Reopening the connection...
RFS mode init Ok
Device : RM-696
HW build : 1507
Bat.level : 36
SW release : (empty)
Protocol : 108
UPDAPP ver : 1.7.2
Upd/Dev PT : 3 , 3
FL_images : cert-sw,xloader,secondary,rootfs,kernel,moslo,config,mm c,tar,cmt-2nd,cmt-algo,cmt-mcusw
Last errors : bb5_rdc_cert_read failed
Code Match Ok
HW match Ok
RFS Set : Host Protocol set to 108
RFS Set : CMT Verify On
RFS Set : Perform RFS On
RFS Set : eMMC preserve On
---Processing MCU image---
Processing File : DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_001-OEM1-958_ARM.bin
RFS : Sending config for [cert-sw]
-> Ver T : RM-696
-> Ver H : 1507 , 1508 , 1509 , 1510 , 1601 , 1602 , 1603 , 1604 , 1605 , 1701 , 1702 , 1703 , 1704 , 1705 , 1801 , 1802 , 1803 , 1804 , 1805
RFS : Init pipe 00
RFS : Flashing...
RFS : Finalizing...
cert-sw Flash done
RFS : Sending config for [kernel]
-> Ver I : 2.6.32-20121301+0m8
RFS : Init pipe 01
RFS : Flashing...
RFS : Finalizing...
kernel Flash done
RFS : Sending config for [rootfs]
-> Ver I : DFL61_HARMATTAN_40.2012.21-3_PR_001
RFS : Init pipe 02
RFS : Flashing...
RFS : Finalizing...
rootfs Flash done
RFS : Sending config for [cmt-2nd]
-> Ver T : RM-696
RFS : Init pipe 03
RFS : Flashing...
RFS : Finalizing...
cmt-2nd Flash done
RFS : Sending config for [cmt-algo]
-> Ver T : RM-696
RFS : Init pipe 04
RFS : Flashing...
RFS : Finalizing...
RFS : ERROR_PIPE_FINAL_REQ FAILED
Receiving error list...
Last errors : Timeout while waiting for the HWBREAK
Could not reboot into cold bootmode
[Pipe 4] Finishing in error state with status 1
Flashing failed
More info in Last Error Log
Elapsed: 00:07:59
Connect phone on selected interface...
После прошивки Winflasher, ТА запустился, Лог WinFlasher:
C:\Documents and Settings\Chip\Рабочий стол\winflasher_2967\WinFlasher>flasher.e
xe -F ape.bin -f -c
flasher 3.12.1 (Oct 6 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.
Using 1st image to detect HW
Suitable USB interface (bootrom) not found, waiting...
Waiting for ASIC id...
Got 69 bytes.
ASIC ID:
05 01 05 01 36 30 07 07 13 02 01 00 12 15 01 ba
94 23 e1 ff 94 78 8c 2c 8a 6a 33 b2 eb 40 eb b3
f0 16 a6 14 15 01 12 dd 2f 66 d4 55 fe 19 2c 62
b9 b8 e2 65 0a fc 1d 9f 3f 90 15 09 01 13 bf 3e
ef 15 52 e7 03
HW variant: HS
Found matching 1st (916)
Sending 1st image (26496 bytes)... done.
Sending HWID query... Received 11 bytes from 1st
ERROR: ReadFile error 31
usb_bulk_read: No error
Got HWID: RM-696:1507
Suitable USB interface (bootrom) not found, waiting...
Waiting for ASIC id...
Got 69 bytes.
ASIC ID:
05 01 05 01 36 30 07 07 13 02 01 00 12 15 01 ba
94 23 e1 ff 94 78 8c 2c 8a 6a 33 b2 eb 40 eb b3
f0 16 a6 14 15 01 12 dd 2f 66 d4 55 fe 19 2c 62
b9 b8 e2 65 0a fc 1d 9f 3f 90 15 09 01 13 bf 3e
ef 15 52 e7 03
Sending 2nd image (26112 bytes)... done.
Sending ping... pong.
Sending ape-algo (7266816 bytes)... done.
Suitable USB interface (bootloader/phonet) not found, waiting...
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1507
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image mmc not present
Image tar skipped
Image config skipped
Battery level 68 %, continuing.
image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[_] cmt-algo [init 100 % 789 / 789 kB NA ]
[ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1684 kB/s]
[_] rootfs [writing 0 % 34816 / 1170282 kB 1746 kB/s]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error
image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[f] cmt-algo [init 0 % 789 / 789 kB NA ]
[-] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1684 kB/s]
[x] rootfs [finished 100 % 1170282 / 1170282 kB 8863 kB/s]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
Timeout while waiting for the HWBREAK
Could not reboot into cold bootmode
[Pipe 6] Finishing in error state with status 1
========================================
ERROR: Failed to flash images
Press Enter To ExitВнутри "муха не сидела", следов воды нет. Правда давно, я на нем менял дисплейный модуль.
Катать бутер?
Лог:
==========
FW APE version : 20.2011.40-4
FW PRx release : PR_1.1
FW Region info : EUROPE [1] , America (Latin , South), South Africa
FW Region ver : 001
==========
Read info Ok
=== SW version Check ====
Ok [Reflashing or Upgrade]
=== SW version Check ====
Processing APE Boot...
File : DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_001-OEM1-958_ARM.bin
Processing : ape-algo
APE Algorithm boot Ok
Reopening the connection...
RFS mode init Ok
Device : RM-696
HW build : 1507
Bat.level : 36
SW release : (empty)
Protocol : 108
UPDAPP ver : 1.7.2
Upd/Dev PT : 3 , 3
FL_images : cert-sw,xloader,secondary,rootfs,kernel,moslo,config,mm c,tar,cmt-2nd,cmt-algo,cmt-mcusw
Last errors : bb5_rdc_cert_read failed
Code Match Ok
HW match Ok
RFS Set : Host Protocol set to 108
RFS Set : CMT Verify On
RFS Set : Perform RFS On
RFS Set : eMMC preserve On
---Processing MCU image---
Processing File : DFL61_HARMATTAN_40.2012.21-3_PR_LEGACY_001-OEM1-958_ARM.bin
RFS : Sending config for [cert-sw]
-> Ver T : RM-696
-> Ver H : 1507 , 1508 , 1509 , 1510 , 1601 , 1602 , 1603 , 1604 , 1605 , 1701 , 1702 , 1703 , 1704 , 1705 , 1801 , 1802 , 1803 , 1804 , 1805
RFS : Init pipe 00
RFS : Flashing...
RFS : Finalizing...
cert-sw Flash done
RFS : Sending config for [kernel]
-> Ver I : 2.6.32-20121301+0m8
RFS : Init pipe 01
RFS : Flashing...
RFS : Finalizing...
kernel Flash done
RFS : Sending config for [rootfs]
-> Ver I : DFL61_HARMATTAN_40.2012.21-3_PR_001
RFS : Init pipe 02
RFS : Flashing...
RFS : Finalizing...
rootfs Flash done
RFS : Sending config for [cmt-2nd]
-> Ver T : RM-696
RFS : Init pipe 03
RFS : Flashing...
RFS : Finalizing...
cmt-2nd Flash done
RFS : Sending config for [cmt-algo]
-> Ver T : RM-696
RFS : Init pipe 04
RFS : Flashing...
RFS : Finalizing...
RFS : ERROR_PIPE_FINAL_REQ FAILED
Receiving error list...
Last errors : Timeout while waiting for the HWBREAK
Could not reboot into cold bootmode
[Pipe 4] Finishing in error state with status 1
Flashing failed
More info in Last Error Log
Elapsed: 00:07:59
Connect phone on selected interface...
После прошивки Winflasher, ТА запустился, Лог WinFlasher:
C:\Documents and Settings\Chip\Рабочий стол\winflasher_2967\WinFlasher>flasher.e
xe -F ape.bin -f -c
flasher 3.12.1 (Oct 6 2011) Harmattan
WARNING: This tool is intended for professional use only. Using it may result
in permanently damaging your device or losing the warranty.
Using 1st image to detect HW
Suitable USB interface (bootrom) not found, waiting...
Waiting for ASIC id...
Got 69 bytes.
ASIC ID:
05 01 05 01 36 30 07 07 13 02 01 00 12 15 01 ba
94 23 e1 ff 94 78 8c 2c 8a 6a 33 b2 eb 40 eb b3
f0 16 a6 14 15 01 12 dd 2f 66 d4 55 fe 19 2c 62
b9 b8 e2 65 0a fc 1d 9f 3f 90 15 09 01 13 bf 3e
ef 15 52 e7 03
HW variant: HS
Found matching 1st (916)
Sending 1st image (26496 bytes)... done.
Sending HWID query... Received 11 bytes from 1st
ERROR: ReadFile error 31
usb_bulk_read: No error
Got HWID: RM-696:1507
Suitable USB interface (bootrom) not found, waiting...
Waiting for ASIC id...
Got 69 bytes.
ASIC ID:
05 01 05 01 36 30 07 07 13 02 01 00 12 15 01 ba
94 23 e1 ff 94 78 8c 2c 8a 6a 33 b2 eb 40 eb b3
f0 16 a6 14 15 01 12 dd 2f 66 d4 55 fe 19 2c 62
b9 b8 e2 65 0a fc 1d 9f 3f 90 15 09 01 13 bf 3e
ef 15 52 e7 03
Sending 2nd image (26112 bytes)... done.
Sending ping... pong.
Sending ape-algo (7266816 bytes)... done.
Suitable USB interface (bootloader/phonet) not found, waiting...
Ping attempt 1 (250 ms)
Server application: 1.7.2
Found product RM-696 rev. 1507
Server implements softupd protocol version 1.8
Image SW version DFL61_HARMATTAN_40.2012.21-3_PR_001
Image moslo not present
Image mmc not present
Image tar skipped
Image config skipped
Battery level 68 %, continuing.
image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[_] cmt-algo [init 100 % 789 / 789 kB NA ]
[ ] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1684 kB/s]
[_] rootfs [writing 0 % 34816 / 1170282 kB 1746 kB/s]
ERROR: SU_GET_UPDATE_STATUS_REQ terminated with error code 1: Unknown error
image [state progress transfer flash speed]
---------------------------------------------------------------------
[x] cert-sw [finished 100 % 1 / 1 kB NA ]
[x] cmt-2nd [finished 100 % 95 / 95 kB NA ]
[f] cmt-algo [init 0 % 789 / 789 kB NA ]
[-] cmt-mcusw [pending 0 % 0 / 0 kB NA ]
[x] xloader [finished 100 % 23 / 23 kB NA ]
[x] secondary [finished 100 % 94 / 94 kB NA ]
[x] kernel [finished 100 % 2714 / 2714 kB 1684 kB/s]
[x] rootfs [finished 100 % 1170282 / 1170282 kB 8863 kB/s]
Fetching error list:
========================================
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
bb5_rdc_cert_read failed
Timeout while waiting for the HWBREAK
Could not reboot into cold bootmode
[Pipe 6] Finishing in error state with status 1
========================================
ERROR: Failed to flash images
Press Enter To ExitВнутри "муха не сидела", следов воды нет. Правда давно, я на нем менял дисплейный модуль.
Катать бутер?