[Ищу] HWC&CCC и PM на 6730с-1 RM-547. [Архив]

ogvozdyk

17.03.2012, 20:26

Какими Боксами располагаете?

Вест, циклон, MXKEY .

Добавлено через 8 минут
И где логи программаторов ?
Что и как сделали, может стоит все таки подробное написать ?

Стирал, лил 31 версию, востанавливаю бекапы и SDD. Делаю локальную SX4(так, как сервер не работает), проливаю разние пм (без 120 и 308 полей, с 1 и 309 полем) и получаю Security status : Security Damaged!!!!! Востанавливал CCC/HWC-тоже самое.

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
Fetching data, wait...

- > Reinsert cable and battery, press powerOn button again
- > For X7, E7 - just waiting, near 1 minute
- > When BEST start Search Phone - Press PowerOn if needed

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C34
EM1 ID: 00000C30
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:03
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128
ADL: Close_Session
Content: 000300000000010000000000000000
ADL: Reboot

Wait, reconneting...

rap= 0750020E5A77034409323FA3D995F2A174A37D59
hash= 25B977A055BE9B5DEC0C38A2A279C695
key= 82B6B4E42E8A6CB0A891E601EC9445F609242E83

Key file updated...

Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Repair SD procedure started...

Phone Imei: 354217033317407
Key file exists, no need to read...
Accepted SdRepReq (on alive SD) by user
Operating mode is OK, no need change...
Writing Super Dongle Key... Ok!
Done!

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok

Security status : Security Damaged!!!!! :(
- > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )

-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!
Local SX4 procedure started...

Phone Imei: 354217033317407
Use custom key...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Upload PM checked
Uploading RF/Battery tune to phone...
RM-547.pm not exist
Select file, please
Using : 6730_RM-547_PM_www.UO5OQ.com.pm
Operating mode is OK, no need change...

Field 1
Record 0 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 6 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 16 write - Ok
Record 18 write - Ok
Record 20 write - Ok
Record 22 write - Ok
Record 23 write - Ok
Record 24 write - Ok
Record 26 write - Ok
Record 28 write - Ok
Record 29 write - Ok
Record 31 write - Ok
Record 33 write - Ok
Record 34 write - Ok
Record 35 write - Ok
Record 39 write - Ok
Record 40 write - Ok
Record 41 write - Ok
Record 42 write - Ok
Record 43 write - Ok
Record 44 write - Ok
Record 45 write - Ok
Field 2
Record 0 write - Ok
Field 4
Record 1 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 9 write - Ok
Record 18 write - Ok
Record 28 write - Ok
Field 8
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Field 11
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Field 12
Record 0 write - Ok
Field 26
Record 0 write - Ok
Record 1 write - Ok
Field 31
Record 4 write - Ok
Field 44
Record 0 write - Ok
Field 50
Record 0 write - Ok
Field 54
Record 0 write - Ok
Record 2 write - Ok
Field 88
Record 0 write - Ok
Field 96
Record 0 write - Ok
Record 1 write - Ok
Field 107
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 25 write - Ok
Record 26 write - Ok
Field 117
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 14 write - Ok
Record 16 write - Ok
Field 153
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Field 193
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 9 write - Ok
Field 217
Record 0 write - Ok
Field 239
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Field 291
Record 0 write - Ok
Field 309
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 7 write - Ok
Record 17 write - Ok
Field 322
Record 0 write - Ok
Field 329
Record 0 write - Ok
Field 334
Record 0 write - Ok
Field 341
Record 0 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Field 354
Record 0 write - Ok
Field 356
Record 0 write - Ok
Record 1 write - Ok
Field 360
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Field 369
Record 0 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => DAMAGED :(
- > Try different PM files or "Restore CCC/HWC" option

Done!

Elapsed: 00:00:11

Upload done

Phone disconected!

Connect phone on selected interface...

Will Write CCC/HWC keys now...

Using : 6730c_RM-547_hwc+ccc_www.UO5OQ.com.rpl
CCC Data found!
HWC Data found!

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C34
EM1 ID: 00000C30
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128
ADL: Preparing for write certificates...

Erase CCC... Ok
Writing CCC... Ok
Erase HWC... Ok
Writing HWC... Ok

ADL: Writing Flash certs done! :)

ADL: Close_Session
Content: 000300000000010000000000000000
ADL: Reboot
All done, disconneting...

Done!

Elapsed: 00:00:11

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok

Security status : Security Damaged!!!!! :(
- > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )

-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

Заливал прошивку с тем-же продукт кодомпо совету PANSoftа.

Connect phone on selected interface...

User ACCEPTED FULL ERASE
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C34
EM1 ID: 00000C30
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128

Reading NPC certificate...
IMEI : 354217033317407
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
Cert Read done!

NPC Certificate saved...
CCC Certificate saved...
HWC Certificate saved...

RPL saved : D:\infiniti\BEST\Backup\Cert\354217033317407_CRT_2 nd.rpl

ADL: Preparing for erase...

Full Erase started...
Asic : CMT , Sub : NAND
Erase Area 0x00000000-0x0FFFFFFF
Erasing Ok , [0F]
Erase done , time : 00:00:01

ADL: Erase done

ADL: Close_Session
Content: 000205000000000000FFFF00000000
ADL: Reboot
Phone disconected!

Connect phone on selected interface...

Core : v1.40 , FlashEngine : v1.23

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm547_021.009_prd.core.fpsx
PPM : rm547_021.009_07.01_Balkans_prd.rofs2.fpsx
PPM2 : rm547_021.009_206.04_VF_GR_prd.rofs3.fpsx
CNT : rm547_021.009_206.03_UDA_VF_GR_prd.uda.fpsx
APE : RM547_APE_ONLY_ENO_09w26_v0.024.fpsx
Flashing phone now...
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C34
EM1 ID: 00000C30
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
- > No any CRT data (MCU damaged/CERT erased), skip saving

===Flashing [MCU]===
Erase : Processing rm547_021.009_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:01
Write : Processing rm547_021.009_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 367 blocks
TIME : Write time : 00:00:14
MCU Write done
ADL: Request programm status
NAND status : 00000001 / 00000000 / 00000000

===Flashing [PPM]===
Erase : Processing rm547_021.009_07.01_Balkans_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm547_021.009_07.01_Balkans_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 142 blocks
TIME : Write time : 00:00:05
PPM Write done
ADL: Request programm status
NAND status : 00000001 / 00000000 / 00000000

===Flashing [PPM2]===
Erase : Processing rm547_021.009_206.04_VF_GR_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm547_021.009_206.04_VF_GR_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 64 blocks
TIME : Write time : 00:00:02
PPM Write done
ADL: Request programm status
NAND status : 00000001 / 00000000 / 00000000

===Flashing [CNT]===
Erase : Processing rm547_021.009_206.03_UDA_VF_GR_prd.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm547_021.009_206.03_UDA_VF_GR_prd.uda.fpsx
Total writen 23 blocks
TIME : Write time : 00:00:01
CNT Write done
ADL: Request programm status
NAND status : 00000001 / 00000000 / 00000000

===Flashing [APE]===
Erase : Processing RM547_APE_ONLY_ENO_09w26_v0.024.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM547_APE_ONLY_ENO_09w26_v0.024.fpsx
CMT: Writing Hash CERT [SOS*ENO]
Total writen 11 blocks
TIME : Write time : 00:00:00
APE Write done
ADL: Request programm status
NAND status : 00000001 / 00000000 / 00000000

ADL: Close_Session
Content: 000300000000010000000000000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:26
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia 6730c-1
Software Info: V ICPR82_09w21.1 28-05-09 RM-547 (c) Nokia
IMEI: 12345610654321?
Ape Version: 021.009
Product code:
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Settings After Flash Defaults...
ProductTuneSet...OK!
SwUpgradeSet...OK!
Product code update...
AfterFlash operations done ;D
Done!

Elapsed: 00:00:48
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Connect phone on selected interface...

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
SimLock Data found!
SimLock key found!
WMDRM key found!
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C34
EM1 ID: 00000C30
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128
ADL: Preparing for write certificates...

Erase NPC... Ok
Writing NPC... Ok
Erase CCC... Ok
Writing CCC... Ok
Erase HWC... Ok
Writing HWC... Ok

ADL: Writing Flash certs done! :)

ADL: Close_Session
Content: 000300000000010000000000000000
ADL: Reboot
Wait, reconneting...

Writing SimLock Key... Ok!
Writing SimLock Data... Ok!

SDD Key status : SDData Damaged!!!!! :(
SimLock status : SimLock is Ok
Security status : Security is Ok

WMDRM_PD key sent... Ok

Done!

Connect phone on selected interface...

Read Uniq key data started...

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
Fetching data, wait...

- > Reinsert cable and battery, press powerOn button again
- > For X7, E7 - just waiting, near 1 minute
- > When BEST start Search Phone - Press PowerOn if needed

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C34
EM1 ID: 00000C30
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128
ADL: Close_Session
Content: 000300000000010000000000000000
ADL: Reboot

Wait, reconneting...

rap= 0750020E5A77034409323FA3D995F2A174A37D59
hash= 25B977A055BE9B5DEC0C38A2A279C695
key= 82B6B4E42E8A6CB0A891E601EC9445F609242E83

Key file updated...

Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Repair SD procedure started...

Phone Imei: 354217033317407
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing Super Dongle Key... Ok!
Done!

Reading Phone Info....
Connected phone - Nokia 6730c-1
Software ver : V ICPR82_09w21.1 28-05-09 RM-547 (c) Nokia
IMEI : 354217033317407
Ape Ver : 021.009
APE Var : 021.009021.009.07.01021.009.206.04
APE ADSP: 256
DSP Ver : ICPR82_09w21.1_RIO
APE Test: 0.024
PPM :
CNT :
Product SN : 0
Product code : 0583026
Base Prd.code:
Module code :
Long Prod.SN : 0
Hardware info=======
HWID :
Retu : 34
Tahvo : 00
Batery: 3952 mV
Camera:
CMT BT:
APE BT:
APE HW: 256
LCDVer:
RF ic :
Lock info ===========
IMEI : 354217033317407
IMEI spNet : 3A 45 12 07 33 13 47 00
IMEI svNet : 33 45 12 07 33 13 47 00 F8

Conf key : 0000000000000000
Provider key : 2440700000000000
Provider : AT&T;U.S.A. (3650)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

SDD key status : Ok
SimLock status : Ok
Security status : Damaged!!!!!
PA_SL3 phone , SP_CODE_LEN : 15

User code : Crypted
UserDataExLevel : Low [Gallery] , FullFlash method

Done!

Local SX4 procedure started...

Phone Imei: 354217033317407
Use custom key...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Done!

Uploading RF/Battery tune to phone...
RM-547.pm not exist
Select file, please
Using : 6730_RM-547_PM_www.UO5OQ.com.pm
Operating mode is OK, no need change...

Field 1
Record 0 write - Ok
Record 2 write - Ok
Record 4 write - Ok
Record 6 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 16 write - Ok
Record 18 write - Ok
Record 20 write - Ok
Record 22 write - Ok
Record 23 write - Ok
Record 24 write - Ok
Record 26 write - Ok
Record 28 write - Ok
Record 29 write - Ok
Record 31 write - Ok
Record 33 write - Ok
Record 34 write - Ok
Record 35 write - Ok
Record 39 write - Ok
Record 40 write - Ok
Record 41 write - Ok
Record 42 write - Ok
Record 43 write - Ok
Record 44 write - Ok
Record 45 write - Ok
Field 2
Record 0 write - Ok
Field 4
Record 1 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 9 write - Ok
Record 18 write - Ok
Record 28 write - Ok
Field 8
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Field 11
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Field 12
Record 0 write - Ok
Field 26
Record 0 write - Ok
Record 1 write - Ok
Field 31
Record 4 write - Ok
Field 44
Record 0 write - Ok
Field 50
Record 0 write - Ok
Field 54
Record 0 write - Ok
Record 2 write - Ok
Field 88
Record 0 write - Ok
Field 96
Record 0 write - Ok
Record 1 write - Ok
Field 107
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 25 write - Ok
Record 26 write - Ok
Field 117
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 14 write - Ok
Record 16 write - Ok
Field 153
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Field 193
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 9 write - Ok
Field 217
Record 0 write - Ok
Field 239
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Field 291
Record 0 write - Ok
Field 309
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 7 write - Ok
Record 17 write - Ok
Field 322
Record 0 write - Ok
Field 329
Record 0 write - Ok
Field 334
Record 0 write - Ok
Field 341
Record 0 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Field 354
Record 0 write - Ok
Field 356
Record 0 write - Ok
Record 1 write - Ok
Field 360
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Field 369
Record 0 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => DAMAGED :(
- > Try different PM files or "Restore CCC/HWC" option

Done!

Elapsed: 00:00:06

Phone disconected!

Connect phone on selected interface...

Will Write CCC/HWC keys now...

Using : 6730c_RM-547_hwc+ccc_www.UO5OQ.com.rpl
CCC Data found!
HWC Data found!

Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
BootRom : 1st boot ok
ASIC ID: 000000030000022600010007600C192102011104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C34
EM1 ID: 00000C30
PUBLIC ID: 0750020E5A77034409323FA3D995F2A174A37D59
ASIC MODE ID: 00
ROOT KEY HASH: 25B977A055BE9B5DEC0C38A2A279C695
ROM ID: 3E273BF637BE26FA
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 11.50.0
Processing RAWLOADER...
FLIC : 00400020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 11.50.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
Waiting for response: 29
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : DA2DB2D32C1B2D9886A55B5D8A14F19ADDC53128
ADL: Preparing for write certificates...

Erase CCC... Ok
Writing CCC... Ok
Erase HWC... Ok
Writing HWC... Ok

ADL: Writing Flash certs done! :)

ADL: Close_Session
Content: 000300000000010000000000000000
ADL: Reboot
All done, disconneting...

Done!

Elapsed: 00:00:18

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok

Security status : Security Damaged!!!!! :(
- > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )

-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

ogvozdyk

19.03.2012, 14:25

Сегодня на работе сделал через Best в связке с UFS. Циклоном не видился телефон. Залил бекап РМ и CCC/HWC, хотя по усб лил раз 10.

Логи прилагаю.

Connect phone on selected interface...

UFS S/N 43222 boot - Ok

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok

Security status : Security Damaged!!!!! :(
- > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )

-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

Local SX4 procedure started...

hone Imei: 354217033317407
Use custom key...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Upload PM checked
Uploading RF/Battery tune to phone...
RM-547.pm not exist
Select file, please
Using : RM-547 Nokia 6730c-1_354217033317407_0_400.pm
Operating mode is OK, no need change...

Field 1
Record 0 write - Error
Record 2 write - Ok
Record 4 write - Ok
Record 6 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 16 write - Ok
Record 18 write - Ok
Record 20 write - Ok
Record 22 write - Ok
Record 23 write - Ok
Record 24 write - Ok
Record 26 write - Ok
Record 28 write - Ok
Record 29 write - Ok
Record 31 write - Ok
Record 33 write - Ok
Record 34 write - Ok
Record 35 write - Ok
Record 39 write - Ok
Record 40 write - Ok
Record 41 write - Ok
Record 42 write - Ok
Record 43 write - Ok
Record 44 write - Ok
Record 45 write - Ok
Field 2
Record 0 write - Ok
Field 4
Record 1 write - Ok
Record 4 write - Ok
Record 28 write - Ok
Field 6
Record 0 write - Ok
Field 8
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 7 write - Ok
Record 8 write - Ok
Record 9 write - Ok
Record 10 write - Ok
Field 11
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Field 12
Record 0 write - Ok
Field 26
Record 0 write - Ok
Record 1 write - Ok
Field 31
Record 4 write - Ok
Field 44
Record 0 write - Ok
Field 50
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Field 54
Record 0 write - Ok
Record 2 write - Ok
Field 88
Record 0 write - Ok
Field 96
Record 0 write - Ok
Record 1 write - Ok
Field 107
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 25 write - Ok
Record 26 write - Ok
Field 117
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Record 8 write - Ok
Record 13 write - Ok
Record 14 write - Ok
Record 16 write - Ok
Field 120
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Field 153
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Field 193
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 9 write - Ok
Field 217
Record 0 write - Ok
Field 239
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 5 write - Ok
Record 6 write - Ok
Field 291
Record 0 write - Ok
Field 308
Record 0 write - Error
Record 1 write - Error
Record 2 write - Error
Record 3 write - Error
Record 4 write - Error
Record 6 write - Error
Record 7 write - Error
Record 9 write - Error
Field 309
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Record 7 write - Ok
Record 17 write - Ok
Field 322
Record 0 write - Ok
Field 329
Record 0 write - Ok
Field 334
Record 0 write - Ok
Field 341
Record 0 write - Ok
Record 3 write - Ok
Record 4 write - Ok
Field 354
Record 0 write - Ok
Field 356
Record 0 write - Ok
Field 360
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Field 369
Record 0 write - Ok

Check ST_SECURITY now...
Security status : ST_SECURITY => OK

Done!

Elapsed: 00:00:29

Upload done

Will Write CCC/HWC keys now...

RM-547.rpl not exist
Select file, please
Using : 354217033317407_CRT.rpl
CCC Data found!
HWC Data found!

Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000030000022600010007600C192102011104
CMT EM0 ID : 00000C34
CMT EM1 ID : 00000C30
CMT PUB ID : 0750020E5A77034409323FA3D995F2A174A37D59
CMT MODE ID : 00
CMT R_HASH : 25B977A055BE9B5DEC0C38A2A279C695
CMT ROM ID : 3E273BF637BE26FA

CMT : Sending 2nd loader...
Use : RAPUv11_2nd.fg , Rev : 0.0 Ver : 1.37.1
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 00400020 , CMT , NOR
CMT Flash ID : 00400020 < ST => M39BORBOAD
FLCNT : 000000EF000100000200611004000500A80700
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAPUv11_algo_xsr16.fg , Rev : 0.0 Ver : 1.40.0
CMT Algo sent
PAPUBkeys blank (erased or HW failure)
Transmission mode : Dual (Ddr, TX2)

Boot Done!

Preparing for write certificates...

CMT : CCC erase Ok
Writing CCC... Ok

CMT : HWC erase Ok
Writing HWC... Ok

Done!

Elapsed: 00:00:27

Connect phone on selected interface...

Checking StartUp data ...
-----------------------
UFS S/N 43222 boot - Ok

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone detected , SP_CODE_LEN : 15

Done!

Всем спасибо. Тему можна закрить.