bobxxlua
29.05.2009, 22:39
Привет, принесли телефон на русификацию, сам он из Турции, родная прошивка была JVIB1
При прошивке сразу же лег телефон, ошибка записи во флешь.
Пытался шить разными боксами- сразу же ошибку писало.
Стал шить потом оптифлешем заметил что ошибка выскакивает на разных секторах, последовательно,
то-есть если сейчас например не прошился 3 сектор, то при повторной прошивке, с галкой difference only, он прошивался, иногда сразу могло прошится несколько секторов, если повезет, то штук 10 :) потом опять пишет- ошибка.
В общем убил 2 дня и так с реконнектами прописал прошивку ему оптиком, TFS прошился без проблем.
В итоге тело стало вкл на заставке , играла мелодия и на телефоне пропадало изображение, и судя по потреблению он висел, пока не передернешь питание.
Внутри телефон идеальный. да и принесли его мне рабочим.
Пробовал на разных компьютерах, разных интерфейсах, разных кабелях, шил через нативный COM-порт- проблема не в этом.
Вот куски лога, прошивки оптиком
E3169 22:23:58 ThreadGUI started
I E3170 22:23:58 ThreadProtocol started
I E3171 22:23:58 OS: NT family, Ver:5.1
I E3172 22:23:58 Boot loader protocol type: passive
I E3173 22:23:58 Memory interface type: 1
I E3174 22:23:58 Setup loader:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\sl_sceptreeg_prime_hw1_s00_m02.s re
I E3175 22:23:58 Setup loader base addr: 0xfc108000
I E3176 22:23:58 Flash loader:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\fl_sceptreeg_vx100_eval_v24_s05_ 2.sre
I E3177 22:23:58 Flash loader base addr: 0x24000000
I E3178 22:23:58 Stack base addr: 0x20000000
I E3179 22:23:58 Stack buffers: 1
I E3180 22:23:58 0: 0x20000000 - 0x23ffffff [64 MB (67108864 Bytes)]
I E3181 22:23:58 Opened COM6 at 115200 baud
I E3182 22:23:58 PC transfer speeds (COM6): 57600 115200 230400 460800 921600
I E3183 22:23:58 Loading S-record file (RangeCheck=Off)
I E3184 22:23:58 File:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\sl_sceptreeg_prime_hw1_s00_m02.s re
I E3185 22:23:58 SRE line 235: IGNORING: S705FC1080006E
I E3186 22:23:58 There is 1 memory region in the S-record file:
I E3187 22:23:58 1: 0xfc108000 - 0xfc108e9b = 3740 Bytes
I E3188 22:23:58 Loading S-record file (RangeCheck=Off)
I E3189 22:23:58 File:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\fl_sceptreeg_vx100_eval_v24_s05_ 2.sre
I E3190 22:23:58 SRE line 33936: IGNORING: S70524000000D6
I E3191 22:23:58 There is 1 memory region in the S-record file:
I E3192 22:23:58 1: 0x24000000 - 0x240848eb = 542956 Bytes
I E3193 22:23:58 Loading S-record file (RangeCheck=On)
I E3194 22:23:58 File: C:\M620\M620XEHF1\M620XEHF1_binary.s3
I E3195 22:23:58 SRE line 8: IGNORING: S70520000000DA
I E3196 22:24:00 SRE line 1702398: IGNORING: S70520300000AA
I E3197 22:24:00 SRE line 1702409: IGNORING: S7052001E000F9
I E3198 22:24:00 SRE line 1702726: IGNORING: S7052001600079
I E3199 22:24:00 SRE line 1771275: IGNORING: S7052007800053
I E3200 22:24:00 SRE line 1772569: IGNORING: S7052000C0001A
I E3201 22:24:00 SRE line 1772570: IGNORING: S015000076783132325F61685F6F675F7373332E7333BE
I E3202 22:24:00 SRE line 1773682: IGNORING: S7052005800055
I E3203 22:24:00 SRE line 1775976: IGNORING: S7052003803C1B
I E3204 22:24:00 There are 9 memory regions in the S-record file:
I E3205 22:24:00 1: 0x20000000 - 0x20000063 = 100 Bytes
I E3206 22:24:00 2: 0x2000c000 - 0x200110cb = 20684 Bytes
I E3207 22:24:00 3: 0x20016000 - 0x200173bf = 5056 Bytes
I E3208 22:24:00 4: 0x2001e000 - 0x2001e09f = 160 Bytes
I E3209 22:24:00 5: 0x2003803c - 0x20040f87 = 36684 Bytes
I E3210 22:24:00 6: 0x20058000 - 0x20058037 = 56 Bytes
I E3211 22:24:00 7: 0x20058138 - 0x2005c665 = 17710 Bytes
I E3212 22:24:00 8: 0x20078000 - 0x20183c37 = 1096760 Bytes
I E3213 22:24:00 9: 0x20300000 - 0x21cf9f4b = 27238220 Bytes
I E3214 22:24:00
SendFile=C:\M620\!\M620_optiflash_Alto_20080115\M6 20_optiflash_Alto_20080115\fl_sceptreeg_vx100_eval _v24_s05_2.sre,
Mode=3
I E3215 22:24:00 Power on mobile !
I E3216 22:24:01 TalkToBootLoader (using COM6)
I E3217 22:24:01 Talking to passive bootloader
I E3218 22:24:03 Bootloader V1.2 using UART1
I E3219 22:24:03 ROM mask ID: 0x00030021 ( !)
I E3220 22:24:03 ID register: 0x00030021 (SC4 ROM)
I E3221 22:24:03 Bootloader type: 13 (0)
I E3222 22:24:03 Max. transfer size: 2048 bytes
I E3223 22:24:03 Data to transfer: 3740 bytes in 1 region(s)
I E3224 22:24:03 Send: 0xfc108000 - 0xfc1087ff (=2048)
I E3225 22:24:03 Send: 0xfc108800 - 0xfc108e9b (=1692)
I E3226 22:24:03 Talking to setup loader
I E3227 22:24:03 Setup loader V2.0 using UART1
I E3228 22:24:03 Setup loader type: 7
I E3229 22:24:03 Max. transfer size: 2048 bytes
I E3230 22:24:03 Adjusted max. transfer size to: 1792 bytes
I E3231 22:24:03 Data to transfer: 542956 bytes in 1 region(s)
I E3232 22:24:03 Send: 0x24000000 - 0x240006ff (=1792)
I E3233 22:24:04 Send: 0x24000700 - 0x2400 0dff (=1792)
SKIPPED
I E3533 22:24:56 Send: 0x24083b00 - 0x240841ff (=1792)
I E3534 22:24:57 Send: 0x24084200 - 0x240848eb (=1772)
I E3535 22:24:57 TalkToBootloader: OK
I E3536 22:24:57 Duration: 56s
I E3537 22:24:57 SendFile=C:\M620\M620XEHF1\M620XEHF1_binary.s3, Mode=0
I E3538 22:24:57 TalkToFlashloader (using COM6)
I E3539 22:24:57 Switching over to flash loader
I E3540 22:24:57 COM6 is connected to UART1
I E3541 22:24:57 Sync'ing to flash loader
I E3542 22:24:57 Sync'ing
I E3543 22:24:57 sync'ed
I E3544 22:24:57 Querying device information
I E3545 22:24:57 Flash loader version: V5.22
I E3546 22:24:57 Max. TX/RX size: 65536/32768
I E3547 22:24:57 Mobile transfer speeds: 57600, 115200, 230400, 460800, 921600,
I E3548 22:24:57 IDs returned by detection: 1
I E3549 22:24:57 AMD:0x01/0x227e3d00, Intel:0x34/0xe59f0000, NAND:0x00/0x00000000(image size=0)
I E3550 22:24:57 Detected flash chips: 1
I E3551 22:24:57 FI_PA:2, PROT_FL_PROG_ALG:2
I E3552 22:24:57 0x01/0x227e3d00: SPANSION, 512Mbit (64 MB (67108864 Bytes) in 518 sectors)
I E3553 22:24:57 Write buffer size: 32
I E3554 22:24:57 COM6: changing baud rate to 921600
I E3555 22:24:57 COM6: baud rate set to 921600
I E3556 22:24:58 Sync'ing
I E3557 22:24:58 sync'ed
I E3558 22:24:58 Port info:
I E3559 22:24:58 Logical port 0: COM6 <-> UART1 at 921600 baud (~100%)
I E3560 22:24:58 TalkToFlashloader: OK
I E3561 22:24:58 There is 1 reserved region defined:
I E3562 22:24:58 1: 0x23fe0000 - 0x23ffffff = 131072 Bytes
I E3563 22:24:58 Data to be transferred: 27 MB (28415430 Bytes)
I E3564 22:24:58 Setup
I E3565 22:24:58 Sector: 0/0
I E3566 22:24:58 VerifyData: 0x20000000 - 0x20000063
I E3567 22:24:58 Sector: 0/1
I E3568 22:24:58 VerifyData: 0x2000c000 - 0x2000c0ff
I E3569 22:24:58 VerifyData: 0x2000c100 - 0x2000ffff
I E3570 22:24:58 Sector: 0/2
I E3571 22:24:58 VerifyData: 0x20010000 - 0x200100ff
I E3572 22:24:58 VerifyData: 0x20010100 - 0x200110cb
I E3573 22:24:58 VerifyData: 0x20016000 - 0x200160ff
I E3574 22:24:58 VerifyData: 0x20016100 - 0x200173bf
I E3575 22:24:58 Sector: 0/3
I E3576 22:24:58 VerifyData: 0x2001e000 - 0x2001e09f
I E3577 22:24:58 Sector: 0/4
I E3578 22:24:58 VerifyData: 0x2003803c - 0x2003813b
I E3579 22:24:58 VerifyData: 0x2003813c - 0x2003ffff
I E3580 22:24:58 Sector: 0/5
I E3581 22:24:58 VerifyData: 0x20040000 - 0x200400ff
I E3582 22:24:58 VerifyData: 0x20040100 - 0x20040f87
I E3583 22:24:58 VerifyData: 0x20058000 - 0x20058037
I E3584 22:24:58 VerifyData: 0x20058138 - 0x20058237
I E3585 22:24:59 VerifyData: 0x20058238 - 0x2005c665
I E3586 22:24:59 Sector: 0/6
I E3587 22:24:59 VerifyData: 0x20078000 - 0x200780ff
I E3588 22:24:59 VerifyData: 0x20078100 - 0x2007ffff
I E3589 22:24:59 Sector: 0/7
I E3590 22:24:59 VerifyData: 0x20080000 - 0x200800ff
I E3591 22:24:59 VerifyData: 0x20080100 - 0x2009ffff
I E3592 22:24:59 Sector: 0/8
I E3593 22:24:59 VerifyData: 0x200a0000 - 0x200a00ff
I E3594 22:24:59 VerifyData: 0x200a0100 - 0x200bffff
I E3595 22:24:59 Sector: 0/9
I E3596 22:24:59 VerifyData: 0x200c0000 - 0x200c00ff
I E3597 22:24:59 VerifyData: 0x200c0100 - 0x200dffff
I E3598 22:25:00 Sector: 0/10
I E3599 22:25:00 VerifyData: 0x200e0000 - 0x200e00ff
I E3600 22:25:00 VerifyData: Detected difference (0x3d0d5cb2 != 0xb9ed03d9)
I E3601 22:25:00 OpenSector: 0/10, 0x200e0000, 131072, 0x11
I E3602 22:25:00 SendData: 0x200e0000 - 0x200effff
I E3603 22:25:01 SendData: 0x200f0000 - 0x200fffff
I E3604 22:25:02 CloseSector: 0/10
I E3605 22:25:02 Sector: 0/11
I E3606 22:25:02 VerifyData: 0x20100000 - 0x201000ff
I E3607 22:25:02 VerifyData: Detected difference (0x342db6cb != 0x46d67610)
I E3608 22:25:02 OpenSector: 0/11, 0x20100000, 131072, 0x11
I E3609 22:25:02 SendData: 0x20100000 - 0x2010ffff
I E3610 22:25:03 SendData: 0x20110000 - 0x2011ffff
I E3611 22:25:04 CloseSector: 0/11
I E3612 22:25:05 Sector: 0/12
I E3613 22:25:05 VerifyData: 0x20120000 - 0x201200ff
I E3614 22:25:05 VerifyData: Detected difference (0xd49e8a20 != 0x11f8a0d1)
I E3615 22:25:05 OpenSector: 0/12, 0x20120000, 131072, 0x11
I E3616 22:25:05 SendData: 0x20120000 - 0x2012ffff
I E3617 22:25:05 SendData: 0x20130000 - 0x2013ffff
I E3618 22:25:21 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3619 22:25:21 0x796c7072 = rply
I E3620 22:25:21 0x67736d2a = *msg
I E3621 22:25:21 0x706d642a = *dmp
I E3622 22:25:21 WaitFor4CCs failed: 6
I E3623 22:25:21 Retry 1: SendData
I E3624 22:25:21 Sync'ing
I E3625 22:25:26 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3626 22:25:26 0x216e7973 = syn!
I E3627 22:25:31 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3628 22:25:31 0x216e7973 = syn!
I E3629 22:25:36 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3630 22:25:36 0x216e7973 = syn!
I E3631 22:25:41 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3632 22:25:41 0x216e7973 = syn!
I E3633 22:25:46 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3634 22:25:46 0x216e7973 = syn!
I E3635 22:25:46 Failed to sync
I E3636 22:25:46 Failed to sync
I E3637 22:25:46 SendFile: 5 (ERR_PROTOCOL)
I E3638 22:25:46 Closed COM6
I E3639 22:25:46 ReLoad: 5 (ERR_PROTOCOL)
I E3640 22:25:46 Error code: ERR_PROTOCOL
E E3641 22:25:46 Sorry, an error has occured ! (ERR_PROTOCOL)
I E3642 22:25:46 ThreadProtocol finished
I E3643 22:25:46 ThreadProtocol: 5
I E3644 22:25:46 ThreadGUI finished
Здесь была ошибка в 12 секторе
I E3645 22:29:30 ThreadGUI started
I E3646 22:29:30 ThreadProtocol started
I E3647 22:29:30 OS: NT family, Ver:5.1
I E3648 22:29:30 Boot loader protocol type: passive
I E3649 22:29:30 Memory interface type: 1
I E3650 22:29:30 Setup loader:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\sl_sceptreeg_prime_hw1_s00_m02.s re
I E3651 22:29:30 Setup loader base addr: 0xfc108000
I E3652 22:29:30 Flash loader:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\fl_sceptreeg_vx100_eval_v24_s05_ 2.sre
I E3653 22:29:30 Flash loader base addr: 0x24000000
I E3654 22:29:30 Stack base addr: 0x20000000
I E3655 22:29:30 Stack buffers: 1
I E3656 22:29:30 0: 0x20000000 - 0x23ffffff [64 MB (67108864 Bytes)]
I E3657 22:29:30 Opened COM6 at 115200 baud
I E3658 22:29:30 PC transfer speeds (COM6): 57600 115200 230400 460800 921600
I E3659 22:29:30 Loading S-record file (RangeCheck=Off)
I E3660 22:29:30 File:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\sl_sceptreeg_prime_hw1_s00_m02.s re
I E3661 22:29:30 SRE line 235: IGNORING: S705FC1080006E
I E3662 22:29:30 There is 1 memory region in the S-record file:
I E3663 22:29:30 1: 0xfc108000 - 0xfc108e9b = 3740 Bytes
I E3664 22:29:30 Loading S-record file (RangeCheck=Off)
I E3665 22:29:30 File:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\fl_sceptreeg_vx100_eval_v24_s05_ 2.sre
I E3666 22:29:30 SRE line 33936: IGNORING: S70524000000D6
I E3667 22:29:30 There is 1 memory region in the S-record file:
I E3668 22:29:30 1: 0x24000000 - 0x240848eb = 542956 Bytes
I E3669 22:29:30 Loading S-record file (RangeCheck=On)
I E3670 22:29:30 File: C:\M620\M620XEHF1\M620XEHF1_binary.s3
I E3671 22:29:30 SRE line 8: IGNORING: S70520000000DA
I E3672 22:29:32 SRE line 1702398: IGNORING: S70520300000AA
I E3673 22:29:32 SRE line 1702409: IGNORING: S7052001E000F9
I E3674 22:29:32 SRE line 1702726: IGNORING: S7052001600079
I E3675 22:29:32 SRE line 1771275: IGNORING: S7052007800053
I E3676 22:29:32 SRE line 1772569: IGNORING: S7052000C0001A
I E3677 22:29:32 SRE line 1772570: IGNORING: S015000076783132325F61685F6F675F7373332E7333BE
I E3678 22:29:32 SRE line 1773682: IGNORING: S7052005800055
I E3679 22:29:32 SRE line 1775976: IGNORING: S7052003803C1B
I E3680 22:29:32 There are 9 memory regions in the S-record file:
I E3681 22:29:32 1: 0x20000000 - 0x20000063 = 100 Bytes
I E3682 22:29:32 2: 0x2000c000 - 0x200110cb = 20684 Bytes
I E3683 22:29:32 3: 0x20016000 - 0x200173bf = 5056 Bytes
I E3684 22:29:32 4: 0x2001e000 - 0x2001e09f = 160 Bytes
I E3685 22:29:32 5: 0x2003803c - 0x20040f87 = 36684 Bytes
I E3686 22:29:32 6: 0x20058000 - 0x20058037 = 56 Bytes
I E3687 22:29:32 7: 0x20058138 - 0x2005c665 = 17710 Bytes
I E3688 22:29:32 8: 0x20078000 - 0x20183c37 = 1096760 Bytes
I E3689 22:29:32 9: 0x20300000 - 0x21cf9f4b = 27238220 Bytes
I E3690 22:29:32
SendFile=C:\M620\!\M620_optiflash_Alto_20080115\M6 20_optiflash_Alto_20080115\fl_sceptreeg_vx100_eval _v24_s05_2.sre,
Mode=3
I E3691 22:29:32 Power on mobile !
I E3692 22:29:33 TalkToBootLoader (using COM6)
I E3693 22:29:33 Talking to passive bootloader
I E3694 22:29:37 Bootloader V1.2 using UART1
I E3695 22:29:37 ROM mask ID: 0x00030021 ( !)
I E3696 22:29:37 ID register: 0x00030021 (SC4 ROM)
I E3697 22:29:37 Bootloader type: 13 (0)
I E3698 22:29:37 Max. transfer size: 2048 bytes
I E3699 22:29:37 Data to transfer: 3740 bytes in 1 region(s)
I E3700 22:29:37 Send: 0xfc108000 - 0xfc1087ff (=2048)
I E3701 22:29:37 Send: 0xfc108800 - 0xfc108e9b (=1692)
I E3702 22:29:37 Talking to setup loader
I E3703 22:29:37 Setup loader V2.0 using UART1
I E3704 22:29:37 Setup loader type: 7
I E3705 22:29:37 Max. transfer size: 2048 bytes
I E3706 22:29:37 Adjusted max. transfer size to: 1792 bytes
I E3707 22:29:37 Data to transfer: 542956 bytes in 1 region(s)
I E3708 22:29:37 Send: 0x24000000 - 0x240006ff (=1792)
I E3709 22:29:38 Send: 0x24000700 - 0x24000dff (=1792)
I E3710 22:29:38 Send: 0x24000e00 - 0x240014ff (=1792)
SKIPPED
I E4009 22:30:30 Send: 0x24083b00 - 0x240841ff (=1792)
I E4010 22:30:31 Send: 0x24084200 - 0x240848eb (=1772)
I E4011 22:30:31 TalkToBootloader: OK
I E4012 22:30:31 Duration: 58s
I E4013 22:30:31 SendFile=C:\M620\M620XEHF1\M620XEHF1_binary.s3, Mode=0
I E4014 22:30:31 TalkToFlashloader (using COM6)
I E4015 22:30:31 Switching over to flash loader
I E4016 22:30:31 COM6 is connected to UART1
I E4017 22:30:31 Sync'ing to flash loader
I E4018 22:30:31 Sync'ing
I E4019 22:30:31 sync'ed
I E4020 22:30:31 Querying device information
I E4021 22:30:31 Flash loader version: V5.22
I E4022 22:30:31 Max. TX/RX size: 65536/32768
I E4023 22:30:31 Mobile transfer speeds: 57600, 115200, 230400, 460800, 921600,
I E4024 22:30:31 IDs returned by detection: 1
I E4025 22:30:31 AMD:0x01/0x227e3d00, Intel:0x34/0xe59f0000, NAND:0x00/0x00000000(image size=0)
I E4026 22:30:31 Detected flash chips: 1
I E4027 22:30:31 FI_PA:2, PROT_FL_PROG_ALG:2
I E4028 22:30:31 0x01/0x227e3d00: SPANSION, 512Mbit (64 MB (67108864 Bytes) in 518 sectors)
I E4029 22:30:31 Write buffer size: 32
I E4030 22:30:31 COM6: changing baud rate to 921600
I E4031 22:30:31 COM6: baud rate set to 921600
I E4032 22:30:32 Sync'ing
I E4033 22:30:32 sync'ed
I E4034 22:30:32 Port info:
I E4035 22:30:32 Logical port 0: COM6 <-> UART1 at 921600 baud (~100%)
I E4036 22:30:32 TalkToFlashloader: OK
I E4037 22:30:32 There is 1 reserved region defined:
I E4038 22:30:32 1: 0x23fe0000 - 0x23ffffff = 131072 Bytes
I E4039 22:30:32 Data to be transferred: 27 MB (28415430 Bytes)
I E4040 22:30:32 Setup
I E4041 22:30:32 Sector: 0/0
I E4042 22:30:32 VerifyData: 0x20000000 - 0x20000063
I E4043 22:30:32 Sector: 0/1
I E4044 22:30:32 VerifyData: 0x2000c000 - 0x2000c0ff
I E4045 22:30:32 VerifyData: 0x2000c100 - 0x2000ffff
I E4046 22:30:32 Sector: 0/2
I E4047 22:30:32 VerifyData: 0x20010000 - 0x200100ff
I E4048 22:30:32 VerifyData: 0x20010100 - 0x200110cb
I E4049 22:30:32 VerifyData: 0x20016000 - 0x200160ff
I E4050 22:30:32 VerifyData: 0x20016100 - 0x200173bf
I E4051 22:30:32 Sector: 0/3
I E4052 22:30:32 VerifyData: 0x2001e000 - 0x2001e09f
I E4053 22:30:32 Sector: 0/4
I E4054 22:30:32 VerifyData: 0x2003803c - 0x2003813b
I E4055 22:30:32 VerifyData: 0x2003813c - 0x2003ffff
I E4056 22:30:33 Sector: 0/5
I E4057 22:30:33 VerifyData: 0x20040000 - 0x200400ff
I E4058 22:30:33 VerifyData: 0x20040100 - 0x20040f87
I E4059 22:30:33 VerifyData: 0x20058000 - 0x20058037
I E4060 22:30:33 VerifyData: 0x20058138 - 0x20058237
I E4061 22:30:33 VerifyData: 0x20058238 - 0x2005c665
I E4062 22:30:33 Sector: 0/6
I E4063 22:30:33 VerifyData: 0x20078000 - 0x200780ff
I E4064 22:30:33 VerifyData: 0x20078100 - 0x2007ffff
I E4065 22:30:33 Sector: 0/7
I E4066 22:30:33 VerifyData: 0x20080000 - 0x200800ff
I E4067 22:30:33 VerifyData: 0x20080100 - 0x2009ffff
I E4068 22:30:33 Sector: 0/8
I E4069 22:30:33 VerifyData: 0x200a0000 - 0x200a00ff
I E4070 22:30:33 VerifyData: 0x200a0100 - 0x200bffff
I E4071 22:30:33 Sector: 0/9
I E4072 22:30:33 VerifyData: 0x200c0000 - 0x200c00ff
I E4073 22:30:33 VerifyData: 0x200c0100 - 0x200dffff
I E4074 22:30:34 Sector: 0/10
I E4075 22:30:34 VerifyData: 0x200e0000 - 0x200e00ff
I E4076 22:30:34 VerifyData: 0x200e0100 - 0x200fffff
I E4077 22:30:34 Sector: 0/11
I E4078 22:30:34 VerifyData: 0x20100000 - 0x201000ff
I E4079 22:30:34 VerifyData: 0x20100100 - 0x2011ffff
I E4080 22:30:34 Sector: 0/12
I E4081 22:30:34 VerifyData: 0x20120000 - 0x201200ff
I E4082 22:30:35 VerifyData: Detected difference (0x3d0d5cb2 != 0x11f8a0d1)
I E4083 22:30:35 OpenSector: 0/12, 0x20120000, 131072, 0x11
I E4084 22:30:35 SendData: 0x20120000 - 0x2012ffff
I E4085 22:30:35 SendData: 0x20130000 - 0x2013ffff
I E4086 22:30:36 CloseSector: 0/12
I E4087 22:30:37 Sector: 0/13
I E4088 22:30:37 VerifyData: 0x20140000 - 0x201400ff
I E4089 22:30:37 VerifyData: Detected difference (0xc3399bd4 != 0x4b04fbf3)
I E4090 22:30:37 OpenSector: 0/13, 0x20140000, 131072, 0x11
I E4091 22:30:37 SendData: 0x20140000 - 0x2014ffff
I E4092 22:30:38 SendData: 0x20150000 - 0x2015ffff
I E4093 22:30:54 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4094 22:30:54 0x796c7072 = rply
I E4095 22:30:54 0x67736d2a = *msg
I E4096 22:30:54 0x706d642a = *dmp
I E4097 22:30:54 WaitFor4CCs failed: 6
I E4098 22:30:54 Retry 1: SendData
I E4099 22:30:54 Sync'ing
I E4100 22:30:59 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4101 22:30:59 0x216e7973 = syn!
I E4102 22:31:04 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4103 22:31:04 0x216e7973 = syn!
I E4104 22:31:09 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4105 22:31:09 0x216e7973 = syn!
I E4106 22:31:14 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4107 22:31:14 0x216e7973 = syn!
I E4108 22:31:19 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4109 22:31:19 0x216e7973 = syn!
I E4110 22:31:19 Failed to sync
I E4111 22:31:19 Failed to sync
I E4112 22:31:19 SendFile: 5 (ERR_PROTOCOL)
I E4113 22:31:19 Closed COM6
I E4114 22:31:19 ReLoad: 5 (ERR_PROTOCOL)
I E4115 22:31:19 Error code: ERR_PROTOCOL
E E4116 22:31:19 Sorry, an error has occured ! (ERR_PROTOCOL)
I E4117 22:31:19 ThreadProtocol finished
I E4118 22:31:19 ThreadProtocol: 5
I E4119 22:31:19 ThreadGUI finished
Здесь 12 сектор прописался, но возникла ошибка в 13 секторе.
Требуется помошь.
При прошивке сразу же лег телефон, ошибка записи во флешь.
Пытался шить разными боксами- сразу же ошибку писало.
Стал шить потом оптифлешем заметил что ошибка выскакивает на разных секторах, последовательно,
то-есть если сейчас например не прошился 3 сектор, то при повторной прошивке, с галкой difference only, он прошивался, иногда сразу могло прошится несколько секторов, если повезет, то штук 10 :) потом опять пишет- ошибка.
В общем убил 2 дня и так с реконнектами прописал прошивку ему оптиком, TFS прошился без проблем.
В итоге тело стало вкл на заставке , играла мелодия и на телефоне пропадало изображение, и судя по потреблению он висел, пока не передернешь питание.
Внутри телефон идеальный. да и принесли его мне рабочим.
Пробовал на разных компьютерах, разных интерфейсах, разных кабелях, шил через нативный COM-порт- проблема не в этом.
Вот куски лога, прошивки оптиком
E3169 22:23:58 ThreadGUI started
I E3170 22:23:58 ThreadProtocol started
I E3171 22:23:58 OS: NT family, Ver:5.1
I E3172 22:23:58 Boot loader protocol type: passive
I E3173 22:23:58 Memory interface type: 1
I E3174 22:23:58 Setup loader:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\sl_sceptreeg_prime_hw1_s00_m02.s re
I E3175 22:23:58 Setup loader base addr: 0xfc108000
I E3176 22:23:58 Flash loader:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\fl_sceptreeg_vx100_eval_v24_s05_ 2.sre
I E3177 22:23:58 Flash loader base addr: 0x24000000
I E3178 22:23:58 Stack base addr: 0x20000000
I E3179 22:23:58 Stack buffers: 1
I E3180 22:23:58 0: 0x20000000 - 0x23ffffff [64 MB (67108864 Bytes)]
I E3181 22:23:58 Opened COM6 at 115200 baud
I E3182 22:23:58 PC transfer speeds (COM6): 57600 115200 230400 460800 921600
I E3183 22:23:58 Loading S-record file (RangeCheck=Off)
I E3184 22:23:58 File:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\sl_sceptreeg_prime_hw1_s00_m02.s re
I E3185 22:23:58 SRE line 235: IGNORING: S705FC1080006E
I E3186 22:23:58 There is 1 memory region in the S-record file:
I E3187 22:23:58 1: 0xfc108000 - 0xfc108e9b = 3740 Bytes
I E3188 22:23:58 Loading S-record file (RangeCheck=Off)
I E3189 22:23:58 File:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\fl_sceptreeg_vx100_eval_v24_s05_ 2.sre
I E3190 22:23:58 SRE line 33936: IGNORING: S70524000000D6
I E3191 22:23:58 There is 1 memory region in the S-record file:
I E3192 22:23:58 1: 0x24000000 - 0x240848eb = 542956 Bytes
I E3193 22:23:58 Loading S-record file (RangeCheck=On)
I E3194 22:23:58 File: C:\M620\M620XEHF1\M620XEHF1_binary.s3
I E3195 22:23:58 SRE line 8: IGNORING: S70520000000DA
I E3196 22:24:00 SRE line 1702398: IGNORING: S70520300000AA
I E3197 22:24:00 SRE line 1702409: IGNORING: S7052001E000F9
I E3198 22:24:00 SRE line 1702726: IGNORING: S7052001600079
I E3199 22:24:00 SRE line 1771275: IGNORING: S7052007800053
I E3200 22:24:00 SRE line 1772569: IGNORING: S7052000C0001A
I E3201 22:24:00 SRE line 1772570: IGNORING: S015000076783132325F61685F6F675F7373332E7333BE
I E3202 22:24:00 SRE line 1773682: IGNORING: S7052005800055
I E3203 22:24:00 SRE line 1775976: IGNORING: S7052003803C1B
I E3204 22:24:00 There are 9 memory regions in the S-record file:
I E3205 22:24:00 1: 0x20000000 - 0x20000063 = 100 Bytes
I E3206 22:24:00 2: 0x2000c000 - 0x200110cb = 20684 Bytes
I E3207 22:24:00 3: 0x20016000 - 0x200173bf = 5056 Bytes
I E3208 22:24:00 4: 0x2001e000 - 0x2001e09f = 160 Bytes
I E3209 22:24:00 5: 0x2003803c - 0x20040f87 = 36684 Bytes
I E3210 22:24:00 6: 0x20058000 - 0x20058037 = 56 Bytes
I E3211 22:24:00 7: 0x20058138 - 0x2005c665 = 17710 Bytes
I E3212 22:24:00 8: 0x20078000 - 0x20183c37 = 1096760 Bytes
I E3213 22:24:00 9: 0x20300000 - 0x21cf9f4b = 27238220 Bytes
I E3214 22:24:00
SendFile=C:\M620\!\M620_optiflash_Alto_20080115\M6 20_optiflash_Alto_20080115\fl_sceptreeg_vx100_eval _v24_s05_2.sre,
Mode=3
I E3215 22:24:00 Power on mobile !
I E3216 22:24:01 TalkToBootLoader (using COM6)
I E3217 22:24:01 Talking to passive bootloader
I E3218 22:24:03 Bootloader V1.2 using UART1
I E3219 22:24:03 ROM mask ID: 0x00030021 ( !)
I E3220 22:24:03 ID register: 0x00030021 (SC4 ROM)
I E3221 22:24:03 Bootloader type: 13 (0)
I E3222 22:24:03 Max. transfer size: 2048 bytes
I E3223 22:24:03 Data to transfer: 3740 bytes in 1 region(s)
I E3224 22:24:03 Send: 0xfc108000 - 0xfc1087ff (=2048)
I E3225 22:24:03 Send: 0xfc108800 - 0xfc108e9b (=1692)
I E3226 22:24:03 Talking to setup loader
I E3227 22:24:03 Setup loader V2.0 using UART1
I E3228 22:24:03 Setup loader type: 7
I E3229 22:24:03 Max. transfer size: 2048 bytes
I E3230 22:24:03 Adjusted max. transfer size to: 1792 bytes
I E3231 22:24:03 Data to transfer: 542956 bytes in 1 region(s)
I E3232 22:24:03 Send: 0x24000000 - 0x240006ff (=1792)
I E3233 22:24:04 Send: 0x24000700 - 0x2400 0dff (=1792)
SKIPPED
I E3533 22:24:56 Send: 0x24083b00 - 0x240841ff (=1792)
I E3534 22:24:57 Send: 0x24084200 - 0x240848eb (=1772)
I E3535 22:24:57 TalkToBootloader: OK
I E3536 22:24:57 Duration: 56s
I E3537 22:24:57 SendFile=C:\M620\M620XEHF1\M620XEHF1_binary.s3, Mode=0
I E3538 22:24:57 TalkToFlashloader (using COM6)
I E3539 22:24:57 Switching over to flash loader
I E3540 22:24:57 COM6 is connected to UART1
I E3541 22:24:57 Sync'ing to flash loader
I E3542 22:24:57 Sync'ing
I E3543 22:24:57 sync'ed
I E3544 22:24:57 Querying device information
I E3545 22:24:57 Flash loader version: V5.22
I E3546 22:24:57 Max. TX/RX size: 65536/32768
I E3547 22:24:57 Mobile transfer speeds: 57600, 115200, 230400, 460800, 921600,
I E3548 22:24:57 IDs returned by detection: 1
I E3549 22:24:57 AMD:0x01/0x227e3d00, Intel:0x34/0xe59f0000, NAND:0x00/0x00000000(image size=0)
I E3550 22:24:57 Detected flash chips: 1
I E3551 22:24:57 FI_PA:2, PROT_FL_PROG_ALG:2
I E3552 22:24:57 0x01/0x227e3d00: SPANSION, 512Mbit (64 MB (67108864 Bytes) in 518 sectors)
I E3553 22:24:57 Write buffer size: 32
I E3554 22:24:57 COM6: changing baud rate to 921600
I E3555 22:24:57 COM6: baud rate set to 921600
I E3556 22:24:58 Sync'ing
I E3557 22:24:58 sync'ed
I E3558 22:24:58 Port info:
I E3559 22:24:58 Logical port 0: COM6 <-> UART1 at 921600 baud (~100%)
I E3560 22:24:58 TalkToFlashloader: OK
I E3561 22:24:58 There is 1 reserved region defined:
I E3562 22:24:58 1: 0x23fe0000 - 0x23ffffff = 131072 Bytes
I E3563 22:24:58 Data to be transferred: 27 MB (28415430 Bytes)
I E3564 22:24:58 Setup
I E3565 22:24:58 Sector: 0/0
I E3566 22:24:58 VerifyData: 0x20000000 - 0x20000063
I E3567 22:24:58 Sector: 0/1
I E3568 22:24:58 VerifyData: 0x2000c000 - 0x2000c0ff
I E3569 22:24:58 VerifyData: 0x2000c100 - 0x2000ffff
I E3570 22:24:58 Sector: 0/2
I E3571 22:24:58 VerifyData: 0x20010000 - 0x200100ff
I E3572 22:24:58 VerifyData: 0x20010100 - 0x200110cb
I E3573 22:24:58 VerifyData: 0x20016000 - 0x200160ff
I E3574 22:24:58 VerifyData: 0x20016100 - 0x200173bf
I E3575 22:24:58 Sector: 0/3
I E3576 22:24:58 VerifyData: 0x2001e000 - 0x2001e09f
I E3577 22:24:58 Sector: 0/4
I E3578 22:24:58 VerifyData: 0x2003803c - 0x2003813b
I E3579 22:24:58 VerifyData: 0x2003813c - 0x2003ffff
I E3580 22:24:58 Sector: 0/5
I E3581 22:24:58 VerifyData: 0x20040000 - 0x200400ff
I E3582 22:24:58 VerifyData: 0x20040100 - 0x20040f87
I E3583 22:24:58 VerifyData: 0x20058000 - 0x20058037
I E3584 22:24:58 VerifyData: 0x20058138 - 0x20058237
I E3585 22:24:59 VerifyData: 0x20058238 - 0x2005c665
I E3586 22:24:59 Sector: 0/6
I E3587 22:24:59 VerifyData: 0x20078000 - 0x200780ff
I E3588 22:24:59 VerifyData: 0x20078100 - 0x2007ffff
I E3589 22:24:59 Sector: 0/7
I E3590 22:24:59 VerifyData: 0x20080000 - 0x200800ff
I E3591 22:24:59 VerifyData: 0x20080100 - 0x2009ffff
I E3592 22:24:59 Sector: 0/8
I E3593 22:24:59 VerifyData: 0x200a0000 - 0x200a00ff
I E3594 22:24:59 VerifyData: 0x200a0100 - 0x200bffff
I E3595 22:24:59 Sector: 0/9
I E3596 22:24:59 VerifyData: 0x200c0000 - 0x200c00ff
I E3597 22:24:59 VerifyData: 0x200c0100 - 0x200dffff
I E3598 22:25:00 Sector: 0/10
I E3599 22:25:00 VerifyData: 0x200e0000 - 0x200e00ff
I E3600 22:25:00 VerifyData: Detected difference (0x3d0d5cb2 != 0xb9ed03d9)
I E3601 22:25:00 OpenSector: 0/10, 0x200e0000, 131072, 0x11
I E3602 22:25:00 SendData: 0x200e0000 - 0x200effff
I E3603 22:25:01 SendData: 0x200f0000 - 0x200fffff
I E3604 22:25:02 CloseSector: 0/10
I E3605 22:25:02 Sector: 0/11
I E3606 22:25:02 VerifyData: 0x20100000 - 0x201000ff
I E3607 22:25:02 VerifyData: Detected difference (0x342db6cb != 0x46d67610)
I E3608 22:25:02 OpenSector: 0/11, 0x20100000, 131072, 0x11
I E3609 22:25:02 SendData: 0x20100000 - 0x2010ffff
I E3610 22:25:03 SendData: 0x20110000 - 0x2011ffff
I E3611 22:25:04 CloseSector: 0/11
I E3612 22:25:05 Sector: 0/12
I E3613 22:25:05 VerifyData: 0x20120000 - 0x201200ff
I E3614 22:25:05 VerifyData: Detected difference (0xd49e8a20 != 0x11f8a0d1)
I E3615 22:25:05 OpenSector: 0/12, 0x20120000, 131072, 0x11
I E3616 22:25:05 SendData: 0x20120000 - 0x2012ffff
I E3617 22:25:05 SendData: 0x20130000 - 0x2013ffff
I E3618 22:25:21 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3619 22:25:21 0x796c7072 = rply
I E3620 22:25:21 0x67736d2a = *msg
I E3621 22:25:21 0x706d642a = *dmp
I E3622 22:25:21 WaitFor4CCs failed: 6
I E3623 22:25:21 Retry 1: SendData
I E3624 22:25:21 Sync'ing
I E3625 22:25:26 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3626 22:25:26 0x216e7973 = syn!
I E3627 22:25:31 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3628 22:25:31 0x216e7973 = syn!
I E3629 22:25:36 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3630 22:25:36 0x216e7973 = syn!
I E3631 22:25:41 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3632 22:25:41 0x216e7973 = syn!
I E3633 22:25:46 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E3634 22:25:46 0x216e7973 = syn!
I E3635 22:25:46 Failed to sync
I E3636 22:25:46 Failed to sync
I E3637 22:25:46 SendFile: 5 (ERR_PROTOCOL)
I E3638 22:25:46 Closed COM6
I E3639 22:25:46 ReLoad: 5 (ERR_PROTOCOL)
I E3640 22:25:46 Error code: ERR_PROTOCOL
E E3641 22:25:46 Sorry, an error has occured ! (ERR_PROTOCOL)
I E3642 22:25:46 ThreadProtocol finished
I E3643 22:25:46 ThreadProtocol: 5
I E3644 22:25:46 ThreadGUI finished
Здесь была ошибка в 12 секторе
I E3645 22:29:30 ThreadGUI started
I E3646 22:29:30 ThreadProtocol started
I E3647 22:29:30 OS: NT family, Ver:5.1
I E3648 22:29:30 Boot loader protocol type: passive
I E3649 22:29:30 Memory interface type: 1
I E3650 22:29:30 Setup loader:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\sl_sceptreeg_prime_hw1_s00_m02.s re
I E3651 22:29:30 Setup loader base addr: 0xfc108000
I E3652 22:29:30 Flash loader:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\fl_sceptreeg_vx100_eval_v24_s05_ 2.sre
I E3653 22:29:30 Flash loader base addr: 0x24000000
I E3654 22:29:30 Stack base addr: 0x20000000
I E3655 22:29:30 Stack buffers: 1
I E3656 22:29:30 0: 0x20000000 - 0x23ffffff [64 MB (67108864 Bytes)]
I E3657 22:29:30 Opened COM6 at 115200 baud
I E3658 22:29:30 PC transfer speeds (COM6): 57600 115200 230400 460800 921600
I E3659 22:29:30 Loading S-record file (RangeCheck=Off)
I E3660 22:29:30 File:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\sl_sceptreeg_prime_hw1_s00_m02.s re
I E3661 22:29:30 SRE line 235: IGNORING: S705FC1080006E
I E3662 22:29:30 There is 1 memory region in the S-record file:
I E3663 22:29:30 1: 0xfc108000 - 0xfc108e9b = 3740 Bytes
I E3664 22:29:30 Loading S-record file (RangeCheck=Off)
I E3665 22:29:30 File:
C:\M620\!\M620_optiflash_Alto_20080115\M620_optifl ash_Alto_20080115\fl_sceptreeg_vx100_eval_v24_s05_ 2.sre
I E3666 22:29:30 SRE line 33936: IGNORING: S70524000000D6
I E3667 22:29:30 There is 1 memory region in the S-record file:
I E3668 22:29:30 1: 0x24000000 - 0x240848eb = 542956 Bytes
I E3669 22:29:30 Loading S-record file (RangeCheck=On)
I E3670 22:29:30 File: C:\M620\M620XEHF1\M620XEHF1_binary.s3
I E3671 22:29:30 SRE line 8: IGNORING: S70520000000DA
I E3672 22:29:32 SRE line 1702398: IGNORING: S70520300000AA
I E3673 22:29:32 SRE line 1702409: IGNORING: S7052001E000F9
I E3674 22:29:32 SRE line 1702726: IGNORING: S7052001600079
I E3675 22:29:32 SRE line 1771275: IGNORING: S7052007800053
I E3676 22:29:32 SRE line 1772569: IGNORING: S7052000C0001A
I E3677 22:29:32 SRE line 1772570: IGNORING: S015000076783132325F61685F6F675F7373332E7333BE
I E3678 22:29:32 SRE line 1773682: IGNORING: S7052005800055
I E3679 22:29:32 SRE line 1775976: IGNORING: S7052003803C1B
I E3680 22:29:32 There are 9 memory regions in the S-record file:
I E3681 22:29:32 1: 0x20000000 - 0x20000063 = 100 Bytes
I E3682 22:29:32 2: 0x2000c000 - 0x200110cb = 20684 Bytes
I E3683 22:29:32 3: 0x20016000 - 0x200173bf = 5056 Bytes
I E3684 22:29:32 4: 0x2001e000 - 0x2001e09f = 160 Bytes
I E3685 22:29:32 5: 0x2003803c - 0x20040f87 = 36684 Bytes
I E3686 22:29:32 6: 0x20058000 - 0x20058037 = 56 Bytes
I E3687 22:29:32 7: 0x20058138 - 0x2005c665 = 17710 Bytes
I E3688 22:29:32 8: 0x20078000 - 0x20183c37 = 1096760 Bytes
I E3689 22:29:32 9: 0x20300000 - 0x21cf9f4b = 27238220 Bytes
I E3690 22:29:32
SendFile=C:\M620\!\M620_optiflash_Alto_20080115\M6 20_optiflash_Alto_20080115\fl_sceptreeg_vx100_eval _v24_s05_2.sre,
Mode=3
I E3691 22:29:32 Power on mobile !
I E3692 22:29:33 TalkToBootLoader (using COM6)
I E3693 22:29:33 Talking to passive bootloader
I E3694 22:29:37 Bootloader V1.2 using UART1
I E3695 22:29:37 ROM mask ID: 0x00030021 ( !)
I E3696 22:29:37 ID register: 0x00030021 (SC4 ROM)
I E3697 22:29:37 Bootloader type: 13 (0)
I E3698 22:29:37 Max. transfer size: 2048 bytes
I E3699 22:29:37 Data to transfer: 3740 bytes in 1 region(s)
I E3700 22:29:37 Send: 0xfc108000 - 0xfc1087ff (=2048)
I E3701 22:29:37 Send: 0xfc108800 - 0xfc108e9b (=1692)
I E3702 22:29:37 Talking to setup loader
I E3703 22:29:37 Setup loader V2.0 using UART1
I E3704 22:29:37 Setup loader type: 7
I E3705 22:29:37 Max. transfer size: 2048 bytes
I E3706 22:29:37 Adjusted max. transfer size to: 1792 bytes
I E3707 22:29:37 Data to transfer: 542956 bytes in 1 region(s)
I E3708 22:29:37 Send: 0x24000000 - 0x240006ff (=1792)
I E3709 22:29:38 Send: 0x24000700 - 0x24000dff (=1792)
I E3710 22:29:38 Send: 0x24000e00 - 0x240014ff (=1792)
SKIPPED
I E4009 22:30:30 Send: 0x24083b00 - 0x240841ff (=1792)
I E4010 22:30:31 Send: 0x24084200 - 0x240848eb (=1772)
I E4011 22:30:31 TalkToBootloader: OK
I E4012 22:30:31 Duration: 58s
I E4013 22:30:31 SendFile=C:\M620\M620XEHF1\M620XEHF1_binary.s3, Mode=0
I E4014 22:30:31 TalkToFlashloader (using COM6)
I E4015 22:30:31 Switching over to flash loader
I E4016 22:30:31 COM6 is connected to UART1
I E4017 22:30:31 Sync'ing to flash loader
I E4018 22:30:31 Sync'ing
I E4019 22:30:31 sync'ed
I E4020 22:30:31 Querying device information
I E4021 22:30:31 Flash loader version: V5.22
I E4022 22:30:31 Max. TX/RX size: 65536/32768
I E4023 22:30:31 Mobile transfer speeds: 57600, 115200, 230400, 460800, 921600,
I E4024 22:30:31 IDs returned by detection: 1
I E4025 22:30:31 AMD:0x01/0x227e3d00, Intel:0x34/0xe59f0000, NAND:0x00/0x00000000(image size=0)
I E4026 22:30:31 Detected flash chips: 1
I E4027 22:30:31 FI_PA:2, PROT_FL_PROG_ALG:2
I E4028 22:30:31 0x01/0x227e3d00: SPANSION, 512Mbit (64 MB (67108864 Bytes) in 518 sectors)
I E4029 22:30:31 Write buffer size: 32
I E4030 22:30:31 COM6: changing baud rate to 921600
I E4031 22:30:31 COM6: baud rate set to 921600
I E4032 22:30:32 Sync'ing
I E4033 22:30:32 sync'ed
I E4034 22:30:32 Port info:
I E4035 22:30:32 Logical port 0: COM6 <-> UART1 at 921600 baud (~100%)
I E4036 22:30:32 TalkToFlashloader: OK
I E4037 22:30:32 There is 1 reserved region defined:
I E4038 22:30:32 1: 0x23fe0000 - 0x23ffffff = 131072 Bytes
I E4039 22:30:32 Data to be transferred: 27 MB (28415430 Bytes)
I E4040 22:30:32 Setup
I E4041 22:30:32 Sector: 0/0
I E4042 22:30:32 VerifyData: 0x20000000 - 0x20000063
I E4043 22:30:32 Sector: 0/1
I E4044 22:30:32 VerifyData: 0x2000c000 - 0x2000c0ff
I E4045 22:30:32 VerifyData: 0x2000c100 - 0x2000ffff
I E4046 22:30:32 Sector: 0/2
I E4047 22:30:32 VerifyData: 0x20010000 - 0x200100ff
I E4048 22:30:32 VerifyData: 0x20010100 - 0x200110cb
I E4049 22:30:32 VerifyData: 0x20016000 - 0x200160ff
I E4050 22:30:32 VerifyData: 0x20016100 - 0x200173bf
I E4051 22:30:32 Sector: 0/3
I E4052 22:30:32 VerifyData: 0x2001e000 - 0x2001e09f
I E4053 22:30:32 Sector: 0/4
I E4054 22:30:32 VerifyData: 0x2003803c - 0x2003813b
I E4055 22:30:32 VerifyData: 0x2003813c - 0x2003ffff
I E4056 22:30:33 Sector: 0/5
I E4057 22:30:33 VerifyData: 0x20040000 - 0x200400ff
I E4058 22:30:33 VerifyData: 0x20040100 - 0x20040f87
I E4059 22:30:33 VerifyData: 0x20058000 - 0x20058037
I E4060 22:30:33 VerifyData: 0x20058138 - 0x20058237
I E4061 22:30:33 VerifyData: 0x20058238 - 0x2005c665
I E4062 22:30:33 Sector: 0/6
I E4063 22:30:33 VerifyData: 0x20078000 - 0x200780ff
I E4064 22:30:33 VerifyData: 0x20078100 - 0x2007ffff
I E4065 22:30:33 Sector: 0/7
I E4066 22:30:33 VerifyData: 0x20080000 - 0x200800ff
I E4067 22:30:33 VerifyData: 0x20080100 - 0x2009ffff
I E4068 22:30:33 Sector: 0/8
I E4069 22:30:33 VerifyData: 0x200a0000 - 0x200a00ff
I E4070 22:30:33 VerifyData: 0x200a0100 - 0x200bffff
I E4071 22:30:33 Sector: 0/9
I E4072 22:30:33 VerifyData: 0x200c0000 - 0x200c00ff
I E4073 22:30:33 VerifyData: 0x200c0100 - 0x200dffff
I E4074 22:30:34 Sector: 0/10
I E4075 22:30:34 VerifyData: 0x200e0000 - 0x200e00ff
I E4076 22:30:34 VerifyData: 0x200e0100 - 0x200fffff
I E4077 22:30:34 Sector: 0/11
I E4078 22:30:34 VerifyData: 0x20100000 - 0x201000ff
I E4079 22:30:34 VerifyData: 0x20100100 - 0x2011ffff
I E4080 22:30:34 Sector: 0/12
I E4081 22:30:34 VerifyData: 0x20120000 - 0x201200ff
I E4082 22:30:35 VerifyData: Detected difference (0x3d0d5cb2 != 0x11f8a0d1)
I E4083 22:30:35 OpenSector: 0/12, 0x20120000, 131072, 0x11
I E4084 22:30:35 SendData: 0x20120000 - 0x2012ffff
I E4085 22:30:35 SendData: 0x20130000 - 0x2013ffff
I E4086 22:30:36 CloseSector: 0/12
I E4087 22:30:37 Sector: 0/13
I E4088 22:30:37 VerifyData: 0x20140000 - 0x201400ff
I E4089 22:30:37 VerifyData: Detected difference (0xc3399bd4 != 0x4b04fbf3)
I E4090 22:30:37 OpenSector: 0/13, 0x20140000, 131072, 0x11
I E4091 22:30:37 SendData: 0x20140000 - 0x2014ffff
I E4092 22:30:38 SendData: 0x20150000 - 0x2015ffff
I E4093 22:30:54 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4094 22:30:54 0x796c7072 = rply
I E4095 22:30:54 0x67736d2a = *msg
I E4096 22:30:54 0x706d642a = *dmp
I E4097 22:30:54 WaitFor4CCs failed: 6
I E4098 22:30:54 Retry 1: SendData
I E4099 22:30:54 Sync'ing
I E4100 22:30:59 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4101 22:30:59 0x216e7973 = syn!
I E4102 22:31:04 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4103 22:31:04 0x216e7973 = syn!
I E4104 22:31:09 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4105 22:31:09 0x216e7973 = syn!
I E4106 22:31:14 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4107 22:31:14 0x216e7973 = syn!
I E4108 22:31:19 WaitFor4CCs failed: ERR_TIMEOUT (6)
I E4109 22:31:19 0x216e7973 = syn!
I E4110 22:31:19 Failed to sync
I E4111 22:31:19 Failed to sync
I E4112 22:31:19 SendFile: 5 (ERR_PROTOCOL)
I E4113 22:31:19 Closed COM6
I E4114 22:31:19 ReLoad: 5 (ERR_PROTOCOL)
I E4115 22:31:19 Error code: ERR_PROTOCOL
E E4116 22:31:19 Sorry, an error has occured ! (ERR_PROTOCOL)
I E4117 22:31:19 ThreadProtocol finished
I E4118 22:31:19 ThreadProtocol: 5
I E4119 22:31:19 ThreadGUI finished
Здесь 12 сектор прописался, но возникла ошибка в 13 секторе.
Требуется помошь.