gena
24.03.2009, 04:43
SERVICE socket
(10 pin layout)
1 - BOX GENIO1
2 - VBAT (5v)
3 - BOX GENIO2
4 - BSI
5 - BOX RX_1
6 - BOX TX_1
7 - MBUS
8 - GND
9 - VPP
10 - BOX GENIO3
As you can see, pinout is compatible with UFS/JAF and other common Nokia boxes. For DCT4 you can plug directly UFS/JAF cables without any adapter. With BB5, most 8-pin market cables have TX2 instead VPP Pin. Our box don't have connected data line to VPP - only to power IC.
Tx2 might be changed ON THE FLY to any of GENIO pins (in further updated maybe also possible 100% flexible pinout modification, so ALL cables on markets will be supported!).
Bundled adapter crossing pin 3 with 9. That means on output from adapter, on pin 8 you will have TX2 (service pin 3) and still compatibility with UFS/JAF cables will be. VPP is not cutted. It's on pin nr 3 (unused pin nr 2 - jaf/ufs cables) so still VPP funcionality can be used on 8 pin cables, instead of purchasing 10 pin! With small mods needed, of course.
You can use too native 10pin Cyclone cables, but they are not avaiable on market at moment.
DIAGNOSTIC socket
1 - VBAT (5v)
2 - USART CLK
3 - USART TXD
4 - FREQ_MEASURMENT_A0
5 - FREQ_MEASURMENT_CLK
6 - DIAG_1_VOLTMETER
7 - DIAG_2_VOLTMETER
8 - DIAG_3_VOLTMETER
9 - USART RXD
10 - GND
Will be used soon.
источник
http://forum.gsmhosting.com/vbb/showthread.php?t=705257
(10 pin layout)
1 - BOX GENIO1
2 - VBAT (5v)
3 - BOX GENIO2
4 - BSI
5 - BOX RX_1
6 - BOX TX_1
7 - MBUS
8 - GND
9 - VPP
10 - BOX GENIO3
As you can see, pinout is compatible with UFS/JAF and other common Nokia boxes. For DCT4 you can plug directly UFS/JAF cables without any adapter. With BB5, most 8-pin market cables have TX2 instead VPP Pin. Our box don't have connected data line to VPP - only to power IC.
Tx2 might be changed ON THE FLY to any of GENIO pins (in further updated maybe also possible 100% flexible pinout modification, so ALL cables on markets will be supported!).
Bundled adapter crossing pin 3 with 9. That means on output from adapter, on pin 8 you will have TX2 (service pin 3) and still compatibility with UFS/JAF cables will be. VPP is not cutted. It's on pin nr 3 (unused pin nr 2 - jaf/ufs cables) so still VPP funcionality can be used on 8 pin cables, instead of purchasing 10 pin! With small mods needed, of course.
You can use too native 10pin Cyclone cables, but they are not avaiable on market at moment.
DIAGNOSTIC socket
1 - VBAT (5v)
2 - USART CLK
3 - USART TXD
4 - FREQ_MEASURMENT_A0
5 - FREQ_MEASURMENT_CLK
6 - DIAG_1_VOLTMETER
7 - DIAG_2_VOLTMETER
8 - DIAG_3_VOLTMETER
9 - USART RXD
10 - GND
Will be used soon.
источник
http://forum.gsmhosting.com/vbb/showthread.php?t=705257