Sadoev.Geo
15.10.2007, 12:18
cect v668 1 sim 3g , сделал формат и он сдох судя по логу повредил еепром ,хотя прога предупредила но решил рискнуть , вот и лог :
ash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
115200
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [enhanced] (or higher) generation
identification data Ok
identification data backup saved: id.D3889EF4.[E519_Y_PCB01_GPRS_MT6226_S01.00_3.BIN_A339158C].rpl
New firmware detected: E519_Y_PCB01_GPRS_MT6226_S01.00_3.BIN
- make "Read detailed information, ask/rpl" operation
- send "backup_system_log_..." file to support
- make "Read full flash" operation
- send flash backup file(s) to support
- include in your e-mail full text from phone back label (phone name etc.)
identification detection finished
device-id: D3889EF4
protocol ver: 04
ver. sw1: E519_Y_PCB01_GPRS_MT6226_S01.00_3.BIN
ver. sw2: E519_Y.00.3
ffs offset/size: 00800000/00200000
detecting eeprom area in 1 chip(s)...
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom found near: 005F0000
Detected eeprom address is non-standard: 005F0000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address[005F0000] confirmed by user
detecting eeprom size...
eeprom size: 00A10000
eeprom chip: 00
eeprom area: 00000000:005F0000-00FFFFFF
flash: EC257E25082501:29EA0000000000
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
formatting...
flash: EC257E25082501:29EA0000000000
Write Done
file saved: backup_system_log_D3889EF4_E519_Y_PCB01_GPRS_MT622 6_S01.00_3.BIN_A339158C_20071015-120811.B0X.bin
Finished, time used: 174 sec
Remove/Install battery now !
фулл отправил сюда [email protected] а что вы посоветуйте ?
ash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
115200
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: EC257E25082501:29EA0000000000
flash: Samsung AMD/Fujitsu std [D 0008x002000 00FEx010000 0008x002000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [enhanced] (or higher) generation
identification data Ok
identification data backup saved: id.D3889EF4.[E519_Y_PCB01_GPRS_MT6226_S01.00_3.BIN_A339158C].rpl
New firmware detected: E519_Y_PCB01_GPRS_MT6226_S01.00_3.BIN
- make "Read detailed information, ask/rpl" operation
- send "backup_system_log_..." file to support
- make "Read full flash" operation
- send flash backup file(s) to support
- include in your e-mail full text from phone back label (phone name etc.)
identification detection finished
device-id: D3889EF4
protocol ver: 04
ver. sw1: E519_Y_PCB01_GPRS_MT6226_S01.00_3.BIN
ver. sw2: E519_Y.00.3
ffs offset/size: 00800000/00200000
detecting eeprom area in 1 chip(s)...
flash: EC257E25082501:29EA0000000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom found near: 005F0000
Detected eeprom address is non-standard: 005F0000
Posible reasons:
1. eeprom is Ok but address is non-standard
2. eeprom damaged and can't be detected
3. eeprom is Ok but detected incorrectly (f.e. unknown eeprom structure)
If you are not sure that detected address is correct:
1. press "NO" (and select standard address or terminate current operation)
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address[005F0000] confirmed by user
detecting eeprom size...
eeprom size: 00A10000
eeprom chip: 00
eeprom area: 00000000:005F0000-00FFFFFF
flash: EC257E25082501:29EA0000000000
Identification Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
formatting...
flash: EC257E25082501:29EA0000000000
Write Done
file saved: backup_system_log_D3889EF4_E519_Y_PCB01_GPRS_MT622 6_S01.00_3.BIN_A339158C_20071015-120811.B0X.bin
Finished, time used: 174 sec
Remove/Install battery now !
фулл отправил сюда [email protected] а что вы посоветуйте ?