Re: Fly E190 не прописывает IMEI
#4
Была установлена прошивка TINNO36_10A_GEMINI_BOOTLOADER_V005_MT6236_E190_PP_ F4_RU_01_13.
При восстановлении IMEI программой MauiMETA - ругался на Data1.cab, который я ему подставлял.
Подумал, что предложенные базы к более высокой прошивке,попытался прошить FlashTool_v3.0952.00 прошивку E190_PP_F4_RU_01_17_1 - ругнулся с ошибкой 4009 - финализция не прошла и ТА не включается.
Таже ошибка с E190_PP_F4_RU_01_13 - не включается.
Прошил с поддержки Fly-E190_TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190 _PP_F4_RU_01_17.BIN_FLNH8BCS0QG0MBP_56M_2011-08-18_En_Ru_Ua.B4M - сразу предупредило, что не сможет финализировать, rpl создать не смог (видать уже не с чего было)...
Код:
COM60 [ProlificSerial0] selected
module v4.27
Device: _Autodetect MT6228-6276 NAND
Checking data, wait...
Action: write flash NAND
write: Firmware
Fly-E190_TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190_PP_F4_RU_01_17.BIN_FLNH8BCS0QG0MBP_56M_2011-08-18_En_Ru_Ua.B4M.bin
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
nfi area detection...
incorrect ext bootloader signature: 10B500F0
bootloader version: TINNO36_10A_GEMINI_BOOTLOADER_V005_MT6236_E190_PP_F4_RU_01_17.bi
nfi area detection (3 cores) finished: Ok
interface: BROM_DLL_v3.1108.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6236:8A02:8A00
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[0052]: 00AD:00B100800055 [HYNIX] HYD0SQG0MF1P
chip size: 128Mb
page/spare size: 0800/0040
pages per block: 0040
bits i/o: 10
address cycles: 04
internal RAM size: 00018000
external RAM: absent
done
Set baudrate (460800)...
done
interesting cpu type found: 6236:8A02:8A00
ram test (40000000)...
testing 32bit...
32bit ram test passed
testing 16bit...
16bit ram test passed
ram test passed
===> detect existing firmware structure...
detect ffs...
ffs offset/size: 04000000/04000000
firmware size: 64Mb
ffs size: 64Mb
detect sec ro...
error:0BF9:S_DA_HANDSET_SEC_INFO_NOT_FOUND
detect custom parameters...
error:0401:S_CUST_PARA_NOT_SUPPORTED
detect project-id...
project-id: E190_PP_F4_RU_01_13
detect NAND info...
number of areas/bytes to read: 1:00080000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
warning: core offset is not detected
nfi area detection (0 cores) finished: failed
warning: ffs can not be detected
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
startup code area #1 detection done
rom info ver: 07
sw version: TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190_PP_F4_RU_01_13.BIN_FLNH8BCS0QG0MBP_56M
project-id: E190_PP_F4_RU_01_13, 00000000
code offset: 00000000
rom info structure: [standard] type (07)
TCL-ID is absent
===> done
nfi area detection...
incorrect ext bootloader signature: 10B500F0
bootloader version: TINNO36_10A_GEMINI_BOOTLOADER_V005_MT6236_E190_PP_F4_RU_01_17.bi
nfi area detection (3 cores) finished: Ok
startup code area #1 check...
rpl file not found: C:\Infinity\MModule\id.00006236.[TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190_PP_F4_RU_01_17.BIN_FLNH8BCS0QG0MBP_56M_D92D389D].rpl
rpl file not found: C:\Infinity\MModule\id.00006236._TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190_PP_F4_RU_01_17.BIN_FLNH8BCS0QG0MBP_56M_D92D389D_.rpl
rpl file not found: C:\Infinity\MModule\backup_security\id.00006236.[TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190_PP_F4_RU_01_17.BIN_FLNH8BCS0QG0MBP_56M_D92D389D].rpl
rpl file not found: C:\Infinity\MModule\backup_security\id.00006236._TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190_PP_F4_RU_01_17.BIN_FLNH8BCS0QG0MBP_56M_D92D389D_.rpl
====================
warning: unknown firmware: TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190_PP_F4_RU_01_17.BIN_FLNH8BCS0QG0MBP_56M_D92D389D
Unknown firmware found (v.4.27, database date: 08.05.2012), user action required:
1. download latest software from support area and try again
2. if no still luck follow the next procedure:
- find good working phone with the same firmware:
TINNO36_10A_GEMINI_PCB01_GPRS_MT6236_S00.E190_PP_F4_RU_01_17.BIN_FLNH8BCS0QG0MBP_56M
- make "Read full flash" operation
- send flash backup files to support: [email protected] or upload files to http://rapidshare.com or http://4shared.com
- include in your e-mail full text from phone back label (phone name etc.)
- be little bit patient and wait update
====================
warning: startup code area #1 data is invalid
warning: startup code area #1 data is invalid
error: startup code area #1 can't be fixed
You can flash phone now but can not finalize it,
in most cases phone CAN NOT power-on.
Do you want to continue anyway ?
number of cores: 3
loading files...
number of areas: 3
done
write...
write bootloader...
.
.
.
write core...
write core...
Disconnect...
done
Finished, time used: 24 min 59 sec
Remove/Install battery now !
Бэкап infinity конечно же я не сделал.
alexi - а вы чем шили?
Мало того, что серийник не смог прописать, так еще и не умеет восстанавливат sec зону, в поддержку поторопись засунуть модель - зачем?
Думаю - это был ХИТРЫЙ коммерческий ход. А проект был один из достойных когда то.
PS: шил через COM port.
Последние файлы
