Ребята есть ли у кого прошивка с русским на Sony Ericsson XPERIA X2?

Ссылка на оригинальную прошивку

Только с рапиды качать придется. В сумме - 130 Mb.

Прошивку скачал а чем её шить? Что то загрузчика не видел там под неё.

Сам лично не шил. Платформа qualcomm, будьте осторожны! Скорее всего через SEUS получится.
А xperia X1 можно шить с флешки:

This is useful if you load a bad image and cannot make an activesync connection for RUU flashing method.
This method works for any 6.1 and 6.5, and even radio rom.

*** Some Kingston brand may have problem to use SD method, no solution other than use RUU method ***

0. Make sure x1 is hard-spl first
1. Make sure yr micro-sd is formatted w/ fat-32
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd, and put that it yr X1
3. Make sure X1 is disconnect to your PC to avoid goes to serial mode (AC power source is OK)
4. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right, and hold the power on button until you see the tri-color screen.
5. Then follow the on-screen instruction

Источник: http://forum.xda-developers.com/showthread.php?t=445662

А вообще обновляется судя по форумам через ActiveSync, как любой девайс на Windows mobile:

*** Tutorial: Flashing ROMs (...and debranding the X1) ***
About this thread: I will explain how to get a new firmware/ROM on your new X1 :-)
To debrand the phone you just flash a different ROM. You also do the same thing to change from EN to GER, or to flash a customized ROM. So it's the same procedure for all of those actions (making it easier to write this tutorial ;-)).

Step 1 has to be done only once. For every following ROM you might want to flash, Step 2 is all you need to do. So let's start:

Step 1 (Preparations)

- Download and install .NET Framework 3.5 SP1
- If you are using Vista, install the Mobile Device Center 6.1
- Set up the ActiveSync (XP) / Mobile Device Center (Vista) connection with your X1
- Charge the battery to at least 50% or more
- (Re)Connect the X1
- Run X1_HardSPL.exe
- Follow the instructions (it should say something like "Image Version: 1.02.111.7" to "1.00.X1")
- If asked, press "Yes" on the X1
- Now a 4-color screen should show up, showing some version Info
- After that, a progressbar screen will be shown and the phone will reboot when finished
- Click "Finish" on the PC
- If you want to check if everything went fine, turn the device off (long power button press), then hold the "volume down" button and turn the device on again, still holding the "volume down" button until the 4-color screen shows up. It should read something like:
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
- Remove and reinsert the battery to exit bootloader mode

You completed the first step and are now able to flash any ROM you want to your X1! (Well, at least any ROM made for the X1 of course ;-))

Step 2 (Flashing ROMs)

Before you start you have to -obviously- download and extract the ROM you want to flash. The file should be named *.image or *.nbh. Before you follow the steps, rename that file to Kovsimg.nbh.

- Format a MicroSD card with FAT32 if not yet done
- Copy the Kovsimg.nbh into the root directory of your MicroSD card and insert the card in your phone
- Turn off the phone (USB cable not attached)
- Remove and reinsert the battery
- Hold the volume down button and turn the device on again, still holding both buttons until the 4-color screen shows up.
- Follow the onscreen instructions

Congratulations. You're done.

Источник: http://forum.xda-developers.com/showthread.php?t=446070
Здесь вот пишут, что пока решения изменить язык для X2 не существует, т.к. нет соответствующего hspl:

http://forum.xda-developers.com/show....php?p=5788479

через seus обновляется нормально. (ключевое слово- обновляется). язык сменить через seus не выйдет.

А через что можно поставить на него русский язык?

ничего доступного для Вас на сегодняшний день нет