Re: Новости и прошивки для "Китайских Чудесных Клонов"
#48
Сегодня бился с поднятием G6 через инфинити
Опять эта ошибка записи.......
----------------
Log opened: [18.01.2007] [20:06:27]
App: D:\Program Files\InfinityBox\ChineseMiracle\ChineseMiracle.ex e
Loading data, wait...
[Infinity Box] v1.13
S/N: 110F:0108
Wait...
Current device: Autodetect
Done
Loading file v.02...
CM_GStar-G6_HW_MAUI.05A.W05.24.V1_May-12-2006_G6_210RU_En_Ru_Cn.B0M.bin Loaded
COM6 selected
Device: Autodetect
Checking data, wait...
Action: Flash write
Write: Firmware
Skip: Customization
Skip: Language Pack
Skip: Eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
Err: boot error[01] can't detect device
Release Power button now !
In case of initial connection problem: on/off "Boot baudrate autoselect" box.
Boot Fail
Finished, time used: 24 sec
Remove/Install battery now !
COM6 selected
Device: Autodetect
Checking data, wait...
Action: Flash write
Write: Firmware
Skip: Customization
Skip: Language Pack
Skip: Eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6219:8A01]...
Release Power button now !
Boot Done
Initialize...
detecting chip[00] in region[00]...
flash: B000B101000000
flash: B000B100000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: B000B004000000
flash: B000B000000000
flash: Intel std [007Fx010000 0008x002000] 8Mb
total number of flash chip detected: 02
Initialize Done
Set baud...
921600
Set baud Done
Check space...
operation mode: Fast detection mode
device parameters autodetection in progress..
detecting chip[00] in region[00]...
flash: B000B101000000
flash: B000B100000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: B000B004000000
flash: B000B000000000
flash: Intel std [007Fx010000 0008x002000] 8Mb
total number of flash chip detected: 02
total flash region size: 01000000
detecting eeprom area in 2 chip(s)...
flash: B000B101000000
flash: B000B100000000
checking area[00000000]: 00000000-007FFFFF...
flash: B000B004000000
flash: B000B000000000
checking area[00800000]: 00000000-007FFFFF...
eeprom found near: 00C00000
Detected eeprom address is non-standard: 00C00000
If you are not sure that detected address is correct:
1. press "NO" right now
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address confirmed by user
detecting eeprom size...
eeprom size: 00400000
eeprom chip: 01
eeprom area detected[00800000]: 00400000-007FFFFF
flash: B000B101000000
flash: B000B100000000
Reading [eeprom]...
file saved: Backup_eeprom_2007-1-18_20-10-14.B0E.bin
Check space Done
Write...
Area: Firmware
flash: B000B101000000
flash: B000B100000000
Write: Firmware
Err: error# 000000B4
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
04:2[01]: Program suspend in effect.
Err: flash write error: 00202000:00002000
Err: error# 000000B4
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
04:2[01]: Program suspend in effect.
Err: flash write error: 00202000:00002000
Err: error# 000000B4
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
04:2[01]: Program suspend in effect.
Err: flash write error: 00202000:00002000
Err: error# 000000B4
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
04:2[01]: Program suspend in effect.
Err: flash write error: 00202000:00002000
Write Fail
Finished, time used: 211 sec
Remove/Install battery now !
COM6 selected
Device: Autodetect
Checking data, wait...
Action: Flash write
Write: Firmware
Skip: Customization
Skip: Language Pack
Skip: Eeprom
Boot...
Press and HOLD Power button now !
Connecting, wait...
Initializing[6219:8A01]...
Release Power button now !
Boot Done
Initialize...
detecting chip[00] in region[00]...
flash: B000B101000000
flash: B000B100000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: B000B004000000
flash: B000B000000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
total number of flash chip detected: 02
Initialize Done
Set baud...
921600
Set baud Done
Check space...
operation mode: Fast detection mode
device parameters autodetection in progress..
detecting chip[00] in region[00]...
flash: B000B101000000
flash: B000B100000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: B000B004000000
flash: B000B000000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
total number of flash chip detected: 02
total flash region size: 01000000
detecting eeprom area in 2 chip(s)...
flash: B000B101000000
flash: B000B100000000
checking area[00000000]: 00000000-007FFFFF...
flash: B000B004000000
flash: B000B000000000
checking area[00800000]: 00000000-007FFFFF...
eeprom found near: 00C00000
Detected eeprom address is non-standard: 00C00000
If you are not sure that detected address is correct:
1. press "NO" right now
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address confirmed by user
detecting eeprom size...
eeprom size: 00400000
eeprom chip: 01
eeprom area detected[00800000]: 00400000-007FFFFF
flash: B000B101000000
flash: B000B100000000
Reading [eeprom]...
file saved: Backup_eeprom_2007-1-18_20-13-58.B0E.bin
Check space Done
Write...
Area: Firmware
flash: B000B101000000
flash: B000B100000000
Write: Firmware
Err: error# 000000B4
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
04:2[01]: Program suspend in effect.
Err: flash write error: 00202000:00002000
Err: error# 000000B4
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
04:2[01]: Program suspend in effect.
Err: flash write error: 00202000:00002000
Write Fail
Finished, time used: 191 sec
Remove/Install battery now !
COM6 selected
Device: Autodetect
Checking data, wait...
Action: Flash write
Write: Firmware
Skip: Customization
Skip: Language Pack
Skip: Eeprom
Boot...
Press and HOLD Power button now !
Connecting, wait...
Initializing[6219:8A01]...
Release Power button now !
Boot Done
Initialize...
detecting chip[00] in region[00]...
flash: B000B101000000
flash: B000B100000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: B000B004000000
flash: B000B000000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
total number of flash chip detected: 02
Initialize Done
Set baud...
230400
Set baud Done
Check space...
operation mode: Fast detection mode
device parameters autodetection in progress..
detecting chip[00] in region[00]...
flash: B000B101000000
flash: B000B100000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
detecting chip[01] in region[00]...
flash: B000B004000000
flash: B000B000000000
flash: Intel std [0008x002000 007Fx010000] 8Mb
total number of flash chip detected: 02
total flash region size: 01000000
detecting eeprom area in 2 chip(s)...
flash: B000B101000000
flash: B000B100000000
checking area[00000000]: 00000000-007FFFFF...
flash: B000B004000000
flash: B000B000000000
checking area[00800000]: 00000000-007FFFFF...
eeprom found near: 00C00000
Detected eeprom address is non-standard: 00C00000
If you are not sure that detected address is correct:
1. press "NO" right now
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address confirmed by user
detecting eeprom size...
eeprom size: 00400000
eeprom chip: 01
eeprom area detected[00800000]: 00400000-007FFFFF
flash: B000B101000000
flash: B000B100000000
Check space Done
Write...
Area: Firmware
flash: B000B101000000
flash: B000B100000000
Write: Firmware
Err: error# 000000B4
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
04:2[01]: Program suspend in effect.
Err: flash write error: 00202000:00002000
Write Fail
Finished, time used: 211 sec
Remove/Install battery now !
-----------------------------
Пробовал по разному - результат один и тотже:
Err: flash write error: 00202000:00002000
А вот родной FlashTool пишет на ура!
Недавно поднял один G6 с инфинити, но не стал потом сливать фулл с трубы с помощью флештула, о чем сегодня и сожалею.