CSL MT6230 после прошивки труп.
#1
Считываем фулл PAGE+SPARE, заливаем обратно , труп!
тело подымается считанным фулом SpiderMan .
фулл :
http://drim.xost.ru/temp/TINNO30_MT6230.rar
Код:
СЧИТЫВАЕМ
Модуль v3.15
Модель: Autodetect 6228-6239 NAND
Проверка данных, ждите...
Action: read firmware NAND
interface: BROM_DLL_v3.1012.00
соединение...
Аппарат должен быть выключен !
Нажмите и ДЕРЖИТЕ кнопку включения !
Connecting...
Booting...
Отпустите кнопку включения !
bootcode current/expected: 3.2/3.2
CPU: 6230:8A02:8A02
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[0018]: 00AD:007900A50000 [HYNIX] HY27XA081G1M
chip size: 128Mb
page/spare size: 0200/0010
pages per block: 0020
bits i/o: 08
address cycles: 04
internal RAM size: 00020000
external RAM: S_DA_RAM_ERROR
Готов
Set baudrate (921600)...
Готов
ram test...
testing...
ram test passed
===> detect existing firmware structure...
detect ffs...
адрес/размер ffs: 02000000/06000000
firmware size: 32Mb
ffs size: 96Mb
detect sec ro...
detect custom parameters...
detect project-id...
project-id: EV990_08a_w0832_MALAYSIA_V1_09
detect NAND info...
number of areas/bytes to read: 1:00010000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
external bootloader is not present
bootloader version: TINNO30_08A_GEMINI_BOOTLOADER_V005_MT6230_EV990_08A_W0832_MALAYS
nfi area detection finished: Ok
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
ошибка: can not read memory: 0FB1:S_FT_NAND_READADDR_NOT_PAGE_ALIGNMENT
ошибка: can not read area #1 (0003F400-000433FF): 0FB1:S_FT_NAND_READADDR_NOT_PAGE_ALIGNMENT
startup code area #1 detection failed
rom info ver: 05
sw version: TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN
project-id: EV990_08a_w0832_MALAYSIA_V1_09, 4C2C0C82
code offset: 00000000
ffs offset/size [01]: 02000000/06000000
rom info structure: 2nd [enhanced] generation
TCL-ID is absent
===> Готов
area size: 32Mb
number of areas/bytes to read: 1:02000000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_SPARE)...
сохранено: C:\Program Files\InfinityBox\ChineseMiracle\CSL\TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09__firmware_20100614-231343.B4M.bin
Disconnect...
Готов
Закончено, потребовалось времени: 12 min 48 sec
Отключите/подключите батарею !
smart-card: disconnected
smart-card: connected
Загрузка файла v.03...
editor_corrected_TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09__firmware_20100614-231343.B4M.bin.B4M.bin loaded
usb bootloader (file) is absent
rom info ver: 05
sw version: TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN
project-id: EV990_08a_w0832_MALAYSIA_V1_09, 4C2C0C82
code offset: 00000000
ffs offset/size [01]: 02000000/06000000
rom info structure: 2nd [enhanced] generation
TCL-ID is absent
Загружен файл с зоной безопасности: startup code area #1
Код:
ВЛИВАЕМ
Модуль v3.15
Модель: Autodetect 6228-6239 NAND
Проверка данных, ждите...
Action: write flash NAND
Запись Firmware
editor_corrected_TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09__firmware_20100614-231343.B4M.bin.B4M.bin
пропуск: Customization/Language Pack
пропуск: Customization
пропуск: Eeprom/ffs
nfi area detection...
nfi scat area detected
nfi area detection finished: Ok
interface: BROM_DLL_v3.1012.00
соединение...
Аппарат должен быть выключен !
Нажмите и ДЕРЖИТЕ кнопку включения !
Connecting...
Booting...
Отпустите кнопку включения !
bootcode current/expected: 3.2/3.2
CPU: 6230:8A02:8A02
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[0018]: 00AD:007900A50000 [HYNIX] HY27XA081G1M
chip size: 128Mb
page/spare size: 0200/0010
pages per block: 0020
bits i/o: 08
address cycles: 04
internal RAM size: 00020000
external RAM: S_DA_RAM_ERROR
Готов
Set baudrate (921600)...
Готов
ram test...
testing...
ram test passed
===> detect existing firmware structure...
detect ffs...
адрес/размер ffs: 02000000/06000000
firmware size: 32Mb
ffs size: 96Mb
detect sec ro...
detect custom parameters...
detect project-id...
project-id: EV990_08a_w0832_MALAYSIA_V1_09
detect NAND info...
number of areas/bytes to read: 1:00010000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
external bootloader is not present
bootloader version: TINNO30_08A_GEMINI_BOOTLOADER_V005_MT6230_EV990_08A_W0832_MALAYS
nfi area detection finished: Ok
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
ошибка: can not read memory: 0FB1:S_FT_NAND_READADDR_NOT_PAGE_ALIGNMENT
ошибка: can not read area #1 (0003F400-000433FF): 0FB1:S_FT_NAND_READADDR_NOT_PAGE_ALIGNMENT
startup code area #1 detection failed
rom info ver: 05
sw version: TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN
project-id: EV990_08a_w0832_MALAYSIA_V1_09, 4C2C0C82
code offset: 00000000
ffs offset/size [01]: 02000000/06000000
rom info structure: 2nd [enhanced] generation
TCL-ID is absent
===> Готов
nfi area detection...
nfi scat area detected
nfi area detection finished: Ok
startup code area #1 check...
rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.00006230.[TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN_820C2C4C].rpl
rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\id.00006230._TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN_820C2C4C_.rpl
rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.00006230.[TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN_820C2C4C].rpl
rpl file not found: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.00006230._TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN_820C2C4C_.rpl
====================
предупреждение: unknown rom info structure: TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN_820C2C4C
Unknown firmware detected (v.3.15, database date: 05.06.2010), user action required:
1. download latest software from support area and try again
2. if no still luck follow the next procedure:
- find good working phone with the same firmware:
TINNO30_08A_GEMINI_PCB03_GPRS_MT6230_S02.EV990_08A_W0832_MALAYSIA_V1_09.BIN
- make "Читать full flash" operation
- send flash backup files to support: [email protected] or upload files to http://rapidshare.com or http://4shared.com
- include in your e-mail full text from phone back label (phone name etc.)
- be little bit patient and wait update
====================
ошибка: startup code area #1 can't be fixed
You can flash phone now but can not finalize it,
in most cases phone CAN NOT power-on.
Do you want to continue anyway ?
прервано пользователем
ошибка: last error: 03E8:S_STOP
Disconnect...
Здесь был вложен файл: CSL _mt6230.jpg (89.9 Кб), но к сожалению был утерян. Если он у Вас есть, свяжитесь с администрацией для его восстановления. Спасибо.
Последние файлы
