Re: Пожелания и рекомендации команде Infinity Box
#425
Вернусь опять к руссификации Iphone 16 Gb
Скачал новую версию Chines Miracle и LanguagePackEdit. Заново зарусил фул. Записал фул в Iphone - он перестал совсем включаться.
При записи были ошибки:
при первой попытке записать:
Код:
COM18 [VCP0] selected
module v2.79
Device: Autodetect 6228-6230 NAND
Checking data, wait...
Action: write NAND flash
read mode: 01
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw 1: APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN
ver. sw 2: APL216_V1.2_20080918, 9C534816
ffs offset/size: 02000000/06000000
id-page1 Ok
end mark #2 found
nfi area detection finished: Ok
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6230:8A02:8A02]...
CPU: MT6230
high speed boot On
chip: 0031:200D:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.020C
loader: 3.748.0
NAND id: ECF10095
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100000095 [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
115200
Set baud Done
Identification ...
reading bootloader structure area (00080000 bytes)...
detecting bootloader structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN
ver. sw 2: APL216_V1.2_20080918, 9C534816
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is damaged, recalculation required
identification#1 detection finished
security area (code #1) calculation...
Identification Done
Write ...
00006000 bytes sent
write core area 1 of 3...
00417400 bytes sent
write core area 2 of 3...
error: code: A500000BF1
error: code: 5A
error: code: A500
error: code:
error: block/offset: 0000230C/008C3000
error: can't write nand core
Write Fail
Finished, time used: 1364 sec
Remove/Install battery now !
при второй попытке записать:
Код:
COM18 [VCP0] selected
module v2.79
Device: Autodetect 6228-6230 NAND
Checking data, wait...
Action: write NAND flash
read mode: 01
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw 1: APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN
ver. sw 2: APL216_V1.2_20080918, 9C534816
ffs offset/size: 02000000/06000000
id-page1 Ok
end mark #2 found
nfi area detection finished: Ok
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6230:8A02:8A02]...
CPU: MT6230
high speed boot On
chip: 0031:200D:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.020C
loader: 3.748.0
NAND id: ECF10095
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100000095 [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
115200
Set baud Done
Identification ...
reading bootloader structure area (00080000 bytes)...
detecting bootloader structure...
warning: probably flash chip completely erased, no bootloader found
nfi area detection finished: failed
detecting bootloader structure by source file...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN
ver. sw 2: APL216_V1.2_20080918, 9C534816
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is Ok
security area (code #1) backup saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.2738D2FB.[APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN_E9B7AC63].rpl
identification#1 detection finished
security area (code #1) calculation...
Identification Done
Write ...
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\system_log_2738D2FB_APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN_E9B7AC63_20090331-201028.B4X.bin
00006000 bytes sent
write core area 1 of 3...
error: code: A500000BF1
error: code: 5AA50700
error: code:
error: block/offset: 000006FB/001BEC00
error: can't write nand core
Write Fail
file saved: C:\Program Files\InfinityBox\ChineseMiracle\backup_security\system_log_2738D2FB_APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN_E9B7AC63_20090331-201336.B4X.bin
Finished, time used: 282 sec
Remove/Install battery now !
при третьей попытке:
Код:
COM18 [VCP0] selected
module v2.79
Device: Autodetect 6228-6230 NAND
Checking data, wait...
Action: write NAND flash
read mode: 01
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw 1: APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN
ver. sw 2: APL216_V1.2_20080918, 9C534816
ffs offset/size: 02000000/06000000
id-page1 Ok
end mark #2 found
nfi area detection finished: Ok
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6230:8A02:8A02]...
CPU: MT6230
high speed boot On
chip: 0031:200D:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.020C
loader: 3.748.0
NAND id: ECF10095
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00EC:00F100000095 [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
460800
Set baud Done
Identification ...
reading bootloader structure area (00080000 bytes)...
detecting bootloader structure...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: APL216_PCB01_GPRS_MT6230_S02.APL216_V1_2_20080918.BIN
ver. sw 2: APL216_V1.2_20080918, 9C534816
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [enhanced] generation
security area (code #1) is damaged, recalculation required
identification#1 detection finished
security area (code #1) calculation...
Identification Done
Write ...
00006000 bytes sent
write core area 1 of 3...
00417400 bytes sent
write core area 2 of 3...
010BEC00 bytes sent
write core area 3 of 3...
00635400 bytes sent
Write Done
Finished, time used: 939 sec
Remove/Install battery now !
прошился и не включается, ни прошивка Firmware с суппорта, ни прошивка фула заранее слитого предыдущей версией ChinesMiracle - не помогают.
всегда:
security area (code #1) is damaged, recalculation required
пытаюсь, сделать repair security area - Chines Miracle говорит:
Код:
COM18 [VCP0] selected
module v2.79
Device: Autodetect 6228-6230 NAND
Checking data, wait...
Action: repair security area
Flash phone with firmware from support area !
Finished, time used: 0 sec
Remove/Install battery now !