Модель неизвестна,на наклейке Nokia N151(RH-12) При включении моргает всеми светодиодами.Infinity определил [MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00.M608_V_1_07_ P1HXM25BC30_CN.BIN].На поддержке есть вот такой (LV918_MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00[1].M608_V_1_02_P1HXM25BC30_CN_16m_En_Cn_Ar_Cn_Ar) прошил,при вкл.стал моргать половиной светодиодов.Вернул назад фулл и епром,получилось первоначальное состояние.Если есть у кого-нибудь скиньте.Кстати RPL автоматом не создался.Вот лог:
Wait...
Device: Autodetect 6205-6227 NOR
Done
Device: Autodetect 6205-6227 NOR
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection active
Action: read eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03]...
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
921600
error: wrong answer[C3]
error: can't work at this speed, use lower speed
Set baud Fail
Finished, time used: 10 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection active
Action: read eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03]...
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
460800
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [standard] (or higher) generation
protocol ver: 04
ver. sw1: MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00.M608_V_1_07_ P1HXM25BC30_CN.BIN
ver. sw2: M608_V_1.07_P1HxM25BC30_CN
ffs offset/size: 00E00000/00200000
detecting eeprom area in 1 chip(s)...
flash: 2088C4FFFFFFFF:2088C400000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom found near: 00E00000
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 00
eeprom area: 00000000:00E00000-00FFFFFF
reading [eeprom[MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00.M608_V_1_07_ P1HXM25BC30_CN.BIN]]...
file saved: backup_eeprom[MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00.M608_V_1_07_ P1HXM25BC30_CN.BIN]_20071020-115124.B0E.bin
Finished, time used: 102 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
Action: read NAND flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03]...
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
error: unknown protocol
NOR: 0000:000000000000 [00000000]
NAND: 0000:000000000000 [00000000]
warning: NOR flash chip not supported or not detected
Initialize Fail
Finished, time used: 28 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection active
Action: read NOR flash
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03]...
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
460800
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [standard] (or higher) generation
protocol ver: 04
ver. sw1: MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00.M608_V_1_07_ P1HXM25BC30_CN.BIN
ver. sw2: M608_V_1.07_P1HxM25BC30_CN
ffs offset/size: 00E00000/00200000
detecting eeprom area in 1 chip(s)...
flash: 2088C4FFFFFFFF:2088C400000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom found near: 00E00000
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 00
eeprom area: 00000000:00E00000-00FFFFFF
reading [flash[MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00.M608_V_1_07_ P1HXM25BC30_CN.BIN]]...
file saved: backup_flash[MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00.M608_V_1_07_ P1HXM25BC30_CN.BIN]_20071020-120347.B0M.bin
Finished, time used: 659 sec
Remove/Install battery now !
WARNING ! Settings will be cleared, user data erased, Imei set to default value !
Make flash backup before this procedure !

Do you want to continue ?
Action: reset settings
Model: Autodetect 6205-6227 NOR
Checking data, wait...
COM4 [VCP0] selected
Phone should be Switched OFF !
Press and HOLD Power button now !
19200
Initializing[6225:8A03]...
Connecting, wait...
error: can't finalize test moide
Operation failed !
Finished, time used: 31 sec
Remove/Install battery now !
COM4 [VCP0] selected
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection active
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6225:8A03]...
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
Initialize Done
Set baud...
460800
Set baud Done
Identification...
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: 2088C4FFFFFFFF:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
number of flash chip/regions detected: 01/01
total flash region size: 01000000
detect device identification, method #1...
detection phase #1...
detect device parameters finished
structure: 2nd [standard] (or higher) generation
protocol ver: 04
ver. sw1: MOBILEDEN25_06B_PCB01_GPRS_MT6225_S00.M608_V_1_07_ P1HXM25BC30_CN.BIN
ver. sw2: M608_V_1.07_P1HxM25BC30_CN
ffs offset/size: 00E00000/00200000
detecting eeprom area in 1 chip(s)...
flash: 2088C4FFFFFFFF:2088C400000000
checking area[00000000]: 00000000-00FFFFFF...
eeprom found near: 00E00000
detecting eeprom size...
eeprom size: 00200000
eeprom chip: 00
eeprom area: 00000000:00E00000-00FFFFFF
detection phase #3...
.................................................. ..............
done
detecting structure pass 1...
.....................
detect standard fat location pass #1...
..................................................
detect standard fat offset pass #1...
detect standard fat data...
fat layout detection complete
eeprom element #1 detected ok
Finished, time used: 46 sec
Remove/Install battery now !

А чего ему создаваться если там судя по логу проц 6225?И может для начала попробовать его просто форматнуть?

именно так и есть.
у аппарат структура прошивки structure: 2nd [standard] (or higher) generation, а такие аппарты не требуют АСК-РПЛ.

Насчёт АСК-РПЛ я читал где-то здесь на форуме.Формат получился,но надо-было выставить complete вместо safe (но это моя ошибка,затупил).
Но теперь проблема в востановлении имея:
[Infinity Box] v1.58
Action: imei
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
error: connection failed !
Operation failed !
Finished, time used: 80 sec
Power off phone now !
Action: imei
Model: Autodetect 6205-6227 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
error: connection failed !
Operation failed !
Finished, time used: 32 sec
Power off phone now !
Не хочет коннектиться,скорость менял,галки ставил и снимал,что ещё можно попробовать?

Телефон должен быть включен о время операции по восстановлению.

Прописать родной IMEI и править в включённом состоянии, там же написано :

Да это я знаю,уже с 10-к телефонов делал.Именно этот никакой реакции на read general info и write.Все остальние функции нормально.

тут написано что набрать чтобы включить КОМ порт правильно:
http://www.atm-box.com/index.php?id=utilities