Re: Samsung NP5110 и KLMAG2GE4A-A002
#5
У меня недавно был в ремонте GT-N8000 c брикнутой KLMAG2GE4A-A002. Родной прошивкой не удалось восстановить. Восстановил прошивкой от KLMAG2GE4A-A001.
Состояние до восстановления
Код:
Z3X EasyJtag Software ver. 2.2.0.2
Loading eMMC Addon Firmware... IO: 1800 mV
Box S/N: ****************, ,FW Ver.: 01.55
CMD Pullup Level:1980 mV
CMD Active Level:2062 mV
Box IO Level:1800 mV
CLK Rate:7000 khz
HiPower mode is ON!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.
[свернуть]
Detect с TP
Код:
Z3X EasyJtag Software ver. 2.2.0.2
Loading eMMC Addon Firmware... IO: 1800 mV
Box S/N: ****************, ,FW Ver.: 01.55
CMD Pullup Level:1978 mV
CMD Active Level:2063 mV
Box IO Level:1800 mV
CLK Rate:7000 khz
HiPower mode is ON!
---------- eMMC Device Information ----------
EMMC CID : 1501003030303030305620110726589C
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
[свернуть]
Восстановление как KLMAG2GE4A-A002
Код:
Z3X EasyJtag Software ver. 2.2.0.2
Loading eMMC Addon Firmware... IO: 1800 mV
Box S/N: ****************, ,FW Ver.: 01.55
CMD Pullup Level:1979 mV
CMD Active Level:2061 mV
Box IO Level:1800 mV
CLK Rate:7000 khz
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Can't read firmware buffer: CMD CRC Error
Done.
[свернуть]
Восстановление как KLMAG2GE4A-A001
Код:
Z3X EasyJtag Software ver. 2.2.0.2
Loading eMMC Addon Firmware... IO: 1800 mV
Box S/N: ****************, ,FW Ver.: 01.55
CMD Pullup Level:1983 mV
CMD Active Level:2060 mV
Box IO Level:1800 mV
CLK Rate:7000 khz
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!
Success!
eMMC firmware is updated now!
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.
[свернуть]
Detect
Код:
Loading eMMC Addon Firmware... IO: 1800 mV
Box S/N: ****************, ,FW Ver.: 01.55
CMD Pullup Level:1981 mV
CMD Active Level:2062 mV
Box IO Level:1800 mV
CLK Rate:7000 khz
HiPower mode is ON!
---------- eMMC Device Information ----------
EMMC CID : 1501004D414732474105C8049C3A5F36
EMMC CSD : D02701320F5903FFF6DBFFFF8A404006
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012 Rev.0x5
EMMC NAME: MAG2GA , S/N: 3355745338
EMMC NAME (HEX): 4D414732474100
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
[свернуть]