Re: Пожелания и рекомендации команде Infinity Box
#605
Philips X800 прошил с суппорта - труп
Код:
COM13 selected
Ìîäóëü v3.87
Ìîäåëü: Philips-X800
Ïðîâåðêà äàííûõ, æäèòå...
Action: write flash NAND
Çàïèñü Firmware
Philips-X800_NOLLEC29_07A_PMJ_PCB03_GPRS_MT6229_S02.X800_M6229X_RUSSIA_V11_En_Ru.B4M.bin
ïðîïóñê: Customization/Language Pack
ïðîïóñê: Customization
ïðîïóñê: Eeprom/ffs
nfi area detection...
external bootloader is not present
bootloader version: NOLLEC29_07A_PMJ_BOOTLOADER_V005_MT6229_X800_M6229X_RUSSIA_V11.b
nfi area detection (3 cores) finished: Ok
interface: BROM_DLL_v3.1016.00
ñîåäèíåíèå...
Àïïàðàò äîëæåí áûòü âûêëþ÷åí !
Íàæìèòå è ÄÅÐÆÈÒÅ êíîïêó âêëþ÷åíèÿ !
Connecting...
Booting...
Îòïóñòèòå êíîïêó âêëþ÷åíèÿ !
bootcode current/expected: 3.2/3.2
CPU: 6229:8A02:8A02
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[0018]: 00AD:007900A50000 [HYNIX] HY27XA081G1M
chip size: 128Mb
page/spare size: 0200/0010
pages per block: 0020
bits i/o: 08
address cycles: 04
internal RAM size: 00020000
external RAM: absent
Ãîòîâ
Set baudrate (921600)...
Ãîòîâ
ram test...
testing 32bit...
32bit ram test passed
testing 16bit...
16bit ram test passed
ram test passed
===> detect existing firmware structure...
detect ffs...
àäðåñ/ðàçìåð ffs: 04000000/04000000
firmware size: 64Mb
ffs size: 64Mb
detect sec ro...
detect custom parameters...
detect project-id...
project-id: X800_M6229X_RUSSIA_V11
detect NAND info...
number of areas/bytes to read: 1:00010000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
external bootloader is not present
bootloader version: NOLLEC29_07A_PMJ_BOOTLOADER_V005_MT6229_X800_M6229X_RUSSIA_V11.b
ïðåäóïðåæäåíèå: id-page1 area is invalid
nfi area detection (0 cores) finished: failed
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
startup code area #1 is invalid
startup code area #1 detection done
rom info ver: 04
sw version: NOLLEC29_07A_PMJ_PCB03_GPRS_MT6229_S02.X800_M6229X_RUSSIA_V11.BIN
project-id: X800_M6229X_RUSSIA_V11, E3CFCDF6
code offset: 00000000
ffs offset/size [01]: 04000000/04000000
rom info structure: [protected] type (04), 1 record(s)
TCL-ID is absent
===> Ãîòîâ
nfi area detection...
external bootloader is not present
bootloader version: NOLLEC29_07A_PMJ_BOOTLOADER_V005_MT6229_X800_M6229X_RUSSIA_V11.b
nfi area detection (3 cores) finished: Ok
startup code area #1 check...
startup code area #1 calculation...
startup code area #1 fixed
number of cores: 3
loading files...
number of areas: 3
Ãîòîâ
write...
write bootloader...
.
write core...
Disconnect...
Ãîòîâ
Çàêîí÷åíî, ïîòðåáîâàëîñü âðåìåíè: 10 min 50 sec
Îòêëþ÷èòå/ïîäêëþ÷èòå áàòàðåþ !
Пробовал различные варианты. Восстанавливается через Флэштул мастер-прошивкой.
Зачем нужна такая поддержка?