Re: Объявление: относительно прошивок для ChineseMiracle
#26
Присоединяюсь к г.Власову
Слита firmware версией 3.15 для редактирования,после чего тело сдохло
Возврат первоначальной прошивки не помог.
Миракль пишет прошивки нет в базе,вышлите...
Выслал,получил ответ-спасибо,пришло,добавим
На этом форуме написал в личку IHelper
С выходом каждого нового миракля пытаюсь вернуть к жизни тело
Безрезультатно
Прошивки нет в базе,вышлите,после прошивки тело может не включиться
Так как терять в принципе нечего нажимаю да,но тело не включается
Прошу любой помощи и любого совета
Код:
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
nfi area detection...
nfi scat area detected
nfi area detection finished: Ok
interface: BROM_DLL_v3.1016.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6235:8A04:8A01
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[0018]: 00AD:007900A50000 [HYNIX] HY27XA081G1M
chip size: 128Mb
page/spare size: 0200/0010
pages per block: 0020
bits i/o: 08
address cycles: 04
internal RAM size: 00010000
external RAM: S_DA_RAM_ERROR
done
Set baudrate (921600)...
done
ram test...
testing...
ram test passed
===> detect existing firmware structure...
detect ffs...
ffs offset/size: 02000000/06000000
firmware size: 32Mb
ffs size: 96Mb
detect sec ro...
detect custom parameters...
detect project-id...
project-id: ZZT.C51P01.1.4T30D0324_MB01
detect NAND info...
number of areas/bytes to read: 1:00034000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
bootloader version: C51_BOOTLOADER_V005_MT6235B_ZZT_C51P01_1_4T30D0324_MB01.bin
nfi area detection finished: Ok
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
error: can not read memory: 0FB1:S_FT_NAND_READADDR_NOT_PAGE_ALIGNMENT
error: can not read area #1 (000FC400-001003FF): 0FB1:S_FT_NAND_READADDR_NOT_PAGE_ALIGNMENT
startup code area #1 detection failed
rom info ver: 07
sw version: C51_PCB01_GPRS_MT6235B_S01.ZZT_C51P01_1_4T30D0324_MB01.BIN
project-id: ZZT.C51P01.1.4T30D0324_MB01, A8DD8AC2
code offset: 00000000
ffs offset/size [01]: 02000000/06000000
rom info structure: 2nd [enhanced] generation
TCL-ID is absent
===> done
nfi area detection...
nfi scat area detected
nfi area detection finished: Ok
startup code area #1 check...
rpl file not found: D:\Program Files\InfinityBox\ChineseMiracle\id.00006235.[C51_PCB01_GPRS_MT6235B_S01.ZZT_C51P01_1_4T30D0324_MB01.BIN_C28ADDA8].rpl
rpl file not found: D:\Program Files\InfinityBox\ChineseMiracle\id.00006235._C51_PCB01_GPRS_MT6235B_S01.ZZT_C51P01_1_4T30D0324_MB01.BIN_C28ADDA8_.rpl
rpl file not found: D:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.00006235.[C51_PCB01_GPRS_MT6235B_S01.ZZT_C51P01_1_4T30D0324_MB01.BIN_C28ADDA8].rpl
rpl file not found: D:\Program Files\InfinityBox\ChineseMiracle\backup_security\id.00006235._C51_PCB01_GPRS_MT6235B_S01.ZZT_C51P01_1_4T30D0324_MB01.BIN_C28ADDA8_.rpl
====================
warning: unknown rom info structure: C51_PCB01_GPRS_MT6235B_S01.ZZT_C51P01_1_4T30D0324_MB01.BIN_C28ADDA8
Unknown firmware detected (v.3.16, database date: 16.07.2010), user action required:
1. download latest software from support area and try again
2. if no still luck follow the next procedure:
- find good working phone with the same firmware:
C51_PCB01_GPRS_MT6235B_S01.ZZT_C51P01_1_4T30D0324_MB01.BIN
- make "Read full flash" operation
- send flash backup files to support: [email protected] or upload files to http://rapidshare.com or http://4shared.com
- include in your e-mail full text from phone back label (phone name etc.)
- be little bit patient and wait update
====================
error: startup code area #1 can't be fixed
You can flash phone now but can not finalize it,
in most cases phone CAN NOT power-on.
Do you want to continue anyway ?
number of cores: 3
loading files...
number of areas: 3
done
write...
write bootloader...
.
.
write core...
Disconnect...
done
Finished, time used: 7 min 56 sec
Remove/Install battery now !