st.gans
28.01.2007, 21:09
GUI v0.91380063
- sadly,but in v0.91380063 DB2020 OTP CID51 support was broken, fixed
- added SERVER-BASED FULL PERMANENT DB2020 UNLOCK. how to use.
select USB as interface. that is REQUIRED.
select K610 as phone model (or any other DB2020 model, they are same)
settings - check "use server for csca unlock/flash", "do full unlock instead of usercode reset for db2020", fill your login details.
back to semc tab, press unlock, attach phone with pressed "C" (or 2+5) buttons.
wait for signature calculation, it can took about 2 minute.
if calculation will fail, your credits will NOT be deducted.
if calculation is success, then signature will be saved in backup\%imei% folder in your setool2 directory.
next, backup will be created so you will be able to restore phone if something will go wrong (hardly believe, but who knows...)
next, you will be prompted to detach phone and turn it on.
do so.
detach phone.
turn it on FULLY
phone will be on 5 locks, that is normal.
connect phone to usb.
if phone will ask you switch to phone mode - switch to phone mode.
it can ask you for drivers,if you not installed them previously.
install all drivers (links below)
be SURE that you install all drivers correctly.
press "testpoint ok"
procedure will continue,phone will be switched off and unlocked.
remember, if something will go wrong - you have a backup of security units.
cost of DB2020 unlock is 12 credits.
currently, BOTH servers are supporting DB2020 unlock
as usual, credits will NOT be recovered in case of connection failures.
NOTE! there is STILL REMAIN SERVER-BASED USERCODE RESET FOR DB2020.
it will work, if you UNCHECK option "do full unlock instead of usercode reset for db2020" and press UNLOCK.
because of recent problems with sql server on support area, i will post links to new version and phone drivers here. hosting provider are informed about probles and, hopefully, they will be solved.
phone drivers
http://setool.net/common/phones.rar
SEtool2
http://setool.net/common/v0.91380063.rar
- sadly,but in v0.91380063 DB2020 OTP CID51 support was broken, fixed
- added SERVER-BASED FULL PERMANENT DB2020 UNLOCK. how to use.
select USB as interface. that is REQUIRED.
select K610 as phone model (or any other DB2020 model, they are same)
settings - check "use server for csca unlock/flash", "do full unlock instead of usercode reset for db2020", fill your login details.
back to semc tab, press unlock, attach phone with pressed "C" (or 2+5) buttons.
wait for signature calculation, it can took about 2 minute.
if calculation will fail, your credits will NOT be deducted.
if calculation is success, then signature will be saved in backup\%imei% folder in your setool2 directory.
next, backup will be created so you will be able to restore phone if something will go wrong (hardly believe, but who knows...)
next, you will be prompted to detach phone and turn it on.
do so.
detach phone.
turn it on FULLY
phone will be on 5 locks, that is normal.
connect phone to usb.
if phone will ask you switch to phone mode - switch to phone mode.
it can ask you for drivers,if you not installed them previously.
install all drivers (links below)
be SURE that you install all drivers correctly.
press "testpoint ok"
procedure will continue,phone will be switched off and unlocked.
remember, if something will go wrong - you have a backup of security units.
cost of DB2020 unlock is 12 credits.
currently, BOTH servers are supporting DB2020 unlock
as usual, credits will NOT be recovered in case of connection failures.
NOTE! there is STILL REMAIN SERVER-BASED USERCODE RESET FOR DB2020.
it will work, if you UNCHECK option "do full unlock instead of usercode reset for db2020" and press UNLOCK.
because of recent problems with sql server on support area, i will post links to new version and phone drivers here. hosting provider are informed about probles and, hopefully, they will be solved.
phone drivers
http://setool.net/common/phones.rar
SEtool2
http://setool.net/common/v0.91380063.rar