[Вопрос] TA-1030 Nokia 3310 DS [Архив]

Jonic77

03.09.2018, 17:29

Infinity-Box [BEST] NK2 v1.04 - модуль в режиме MTK
Infinity-Box BEST Nokia [HMD] Module [NK2] v1.04

Operation : Identify [ v1.04 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

Нет детекта -

старый BEST 2.29 - чекнул и вычитал на раз два.

Reading Phone Info....
Software ver : 11.02.11 00-00-00 TA-1030
IMEI 1 : 355810094598003
IMEI 2 : 355810095598002
XappVer : 000008F2
Ape Ver : NEMO G 4122fe8d/1 (00000000+0) T Thu Dec 29 01:31:09 2016 U d61db836
PPM : AE
CNT : RETRO.11.02.11.p1
Product SN : 026D28FLU
Product code : 059X9T4
Base Prd.code: 059Z379
Module code : 0207297
Hardware info=======
HWID : 1000
LCDVer: TPO
Lock info ===========
IMEI : 355810094598003
IMEI spNet : 3A 55 18 00 49 95 08 30

Conf key : 800000000004000B
Provider key : 2440700000000000
Country : Finland
Operator : NOKIA (Open)

Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;

SimLock status : Ok
Security status : Ok

Done!

--- Insert USB cable now! ---
Wait for phone...
Phone found! [ 26 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0001
BB_CPU_SN : C928D67FA87559786643F88A97EC82B7
BROM Protocol Version : 05
BROM Status : 0000
Comm Status : 0000
EXBL Status : Alive [ USB Load Active ]
Switch to BL done
BL Version : 01
Setting...
Setting done , result code 0x8000
Project ID : RETRO.11.02.11.p1
BROM/BL stage done
Configure RAMINIT Ok
Reading flash now ...
Done!

Control Block Validation (Security Test) :
CBR is Ok, match with BB SN. Phone Security is Alive :)
Mobile Info
IMEI : 355810094598003
BBUID : C928D67FA87559786643F88A97EC82B7
PCCode: 059X9T4
SimLock Info :
STATE : OPENED ( NOT LOCKED )

Dump Saved to : 355810094598003_MTKx.bin
RPL Saved to : 355810094598003_MTKx.mtsec

Read Done!

Connect phone on selected interface...

fedja

19.09.2018, 21:10

BEST2 вроде для дроидов только) Например Nokia 3 (Тип процессора: MediaTek MT6737).

Прошивка Nokia 3310 ta-1030 InfinityBox BEST2
Infinity-Box BEST Nokia [HMD] Module [NK2] v1.05

Open VPLfile : TA1030_059X9V3_11.02.11.vpl
Description : TA-1030 NDT EURO EI GREY CYRIL RU
DeviceType : TA-1030
ProductCode : 059X9V3
SoftwareVer : 11.02.11
Load Ok!

Operation : Write FirmWare [ v1.05 ]
Setting : UserData erase : False

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM10)
MODE : NOKIA USB SERIAL
PORT : 10
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C015395E8631125188BDC4F1D1FC943F
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : RETRO.11.02.11.p1
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : RETRO.11.02.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Agent : v03.02 on BBID : 0x8B

NOR: 00EF : 0060 : 0018 : 0000
NOR: [WINBOND] W25Q128FW
NOR:
TSIZE : 0x01000000 [ 16,00 MB ]
PSIZE : 0x01000000 [ 16,00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

Load FlashSet :
MROM : TA-1030_ROM_eMP_11.02.11
LANG : TA-1030_LANG_PACK_ROM_EI_eMP_11.02.11_001
CUST : TA-1030_CUSTPACK_ROM_EI_EURO_RU_eMP_11.02.11_001
JUMP : TA-1030_JUMP_TABLE_EI_EURO_RU_eMP_11.02.11_001
VIVA : TA-1030_VIVA_eMP_11.02.11

Prepare FlashSet :
DCR : TA-1030_ROM_eMP_11.02.11
DCR : TA-1030_LANG_PACK_ROM_EI_eMP_11.02.11_001
DCR : TA-1030_CUSTPACK_ROM_EI_EURO_RU_eMP_11.02.11_001
DCR : TA-1030_JUMP_TABLE_EI_EURO_RU_eMP_11.02.11_001
DCR : TA-1030_VIVA_eMP_11.02.11

Prepare Target
SDS : OK : 0x00FF4000 : 0x0000C000

Erase Target Flash
Erase done!

Write Target Flash
Write : TA-1030_ROM_eMP_11.02.11
Write : TA-1030_LANG_PACK_ROM_EI_eMP_11.02.11_001
Write : TA-1030_CUSTPACK_ROM_EI_EURO_RU_eMP_11.02.11_001
Write : TA-1030_JUMP_TABLE_EI_EURO_RU_eMP_11.02.11_001
Write : TA-1030_VIVA_eMP_11.02.11
Write done, waiting target response ...
Write flash done!

Verify Target FlashContent
Verify : TA-1030_ROM_eMP_11.02.11
Verify : TA-1030_LANG_PACK_ROM_EI_eMP_11.02.11_001
Verify : TA-1030_CUSTPACK_ROM_EI_EURO_RU_eMP_11.02.11_001
Verify : TA-1030_JUMP_TABLE_EI_EURO_RU_eMP_11.02.11_001
Verify : TA-1030_VIVA_eMP_11.02.11

Done!
Elapsed: 00:02:54

Reconnect Power/Cable!

Operation : Identify [ v1.05 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM10)
MODE : NOKIA USB SERIAL
PORT : 10
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C015395E8631125188BDC4F1D1FC943F
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : RETRO.11.02.11.p1
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : RETRO.11.02.11.p1
FLASH : 00EF : 0060 : 0018 : 0000
BBSN : C015395E8631125188BDC4F1D1FC943F
PRDC : 059X9V3
IMEI[1] : 357300083739469
IMEI[2] : 357300083739477

Done!
Elapsed: 00:00:29

Reconnect Power/Cable!

Operation : Identify [ v1.05 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM10)
MODE : NOKIA USB SERIAL
PORT : 10
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C928D67FA87559786643F88A97EC82B7
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : RETRO.11.02.11.p1
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : RETRO.11.02.11.p1
FLASH : 00EF : 0060 : 0018 : 0000
BBSN : C928D67FA87559786643F88A97EC82B7
PRDC : 059X9T4
IMEI[1] : 355810094598003
IMEI[2] : 355810095598002

Done!
Elapsed: 00:00:24

Reconnect Power/Cable!

Operation : Write FirmWare [ v1.05 ]
Setting : UserData erase : True

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM10)
MODE : NOKIA USB SERIAL
PORT : 10
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C928D67FA87559786643F88A97EC82B7
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : RETRO.11.02.11.p1
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6260
AGENT : RETRO.11.02.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Agent : v03.02 on BBID : 0x8B

NOR: 00C2 : 0025 : 0038 : 0000
NOR: [MXIC] MX25U12835FZNI_10G
NOR:
TSIZE : 0x01000000 [ 16,00 MB ]
PSIZE : 0x01000000 [ 16,00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST

STATUS : OK
BSTYLE : SF_FLASH_BOOT

Boot done!

Load FlashSet :
MROM : TA-1030_ROM_eMP_11.02.11
LANG : TA-1030_LANG_PACK_ROM_EI_eMP_11.02.11_001
CUST : TA-1030_CUSTPACK_ROM_EI_EURO_RU_eMP_11.02.11_001
JUMP : TA-1030_JUMP_TABLE_EI_EURO_RU_eMP_11.02.11_001
VIVA : TA-1030_VIVA_eMP_11.02.11

Prepare FlashSet :
DCR : TA-1030_ROM_eMP_11.02.11
DCR : TA-1030_LANG_PACK_ROM_EI_eMP_11.02.11_001
DCR : TA-1030_CUSTPACK_ROM_EI_EURO_RU_eMP_11.02.11_001
DCR : TA-1030_JUMP_TABLE_EI_EURO_RU_eMP_11.02.11_001
DCR : TA-1030_VIVA_eMP_11.02.11

Prepare Target
SDS : OK : 0x00FF4000 : 0x0000C000
FFS Format Ok!

Erase Target Flash
Erase done!

Write Target Flash
Write : TA-1030_ROM_eMP_11.02.11
Write : TA-1030_LANG_PACK_ROM_EI_eMP_11.02.11_001
Write : TA-1030_CUSTPACK_ROM_EI_EURO_RU_eMP_11.02.11_001
Write : TA-1030_JUMP_TABLE_EI_EURO_RU_eMP_11.02.11_001
Write : TA-1030_VIVA_eMP_11.02.11
Write done, waiting target response ...
Write flash done!

Verify Target FlashContent
Verify : TA-1030_ROM_eMP_11.02.11
Verify : TA-1030_LANG_PACK_ROM_EI_eMP_11.02.11_001
Verify : TA-1030_CUSTPACK_ROM_EI_EURO_RU_eMP_11.02.11_001
Verify : TA-1030_JUMP_TABLE_EI_EURO_RU_eMP_11.02.11_001
Verify : TA-1030_VIVA_eMP_11.02.11

Done!
Elapsed: 00:03:05

Reconnect Power/Cable!

Operation : Identify [ v1.05 ]

1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : Care Suite USB Serial Port (COM10)
MODE : NOKIA USB SERIAL
PORT : 10
BROM : Init BROM
BROM init passed!
CHIP : MT6260 , SBID : 0xCB00 , HWVR : 0x8000 , SWVR : 0x0000
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : C928D67FA87559786643F88A97EC82B7
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : RETRO.11.02.11.p1
BOOT : PSRM : Init
BOOT : PSRM : 0003

Boot done!

SWVer : RETRO.11.02.11.p1
FLASH : 00EF : 0060 : 0018 : 0000
BBSN : C928D67FA87559786643F88A97EC82B7
PRDC : 059X9T4
IMEI[1] : 355810094598003
IMEI[2] : 355810095598002

Done!
Elapsed: 00:00:26

Reconnect Power/Cable!

https://youtu.be/812AHoP0I4A