Meizu MX5 dump

[TPS79]

Дамп без разделов system/cache/userdata. Остался посля снятия аккаунта flyme,
пароль не стал убирать (лень))

meizu_dump_m85e6795

https://drive.google.com/open?id=0Bw9zPuCNWkHTWmlwQWlJdFk5R0k

Z3X EasyJtag Software ver. 2.1.1.1
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: , ,FW Ver.: 01.55
CMD Pullup Level:2062 mV
CMD Active Level:2660 mV
Box IO Level:2800 mV
CLK Rate:14000 khz
HiPower™ mode is off!
eMMC Device Information
EMMC CID : 15010042474E44335201E97AB2628224
EMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 08/2015 Rev.0x1
EMMC NAME: BGND3R , S/N: 3917132386
EMMC NAME (HEX): 42474E44335200
EMMC ROM1 (Main User Data) Capacity: 29820 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: BGND3R_3917132386_20160723_1401.extcsd
Searching for partition tables...
Detected GPT over MBR...
Medium UUID: 00000000-0000-0000-0000-000000000000
Warning: Entries Count = 21
MMCBLK0P0 (PROINFO) Range: [0X80000,0X77FE00] ,Len: 700000
MMCBLK0P1 (NVRAM) Range: [0X780000,0XC7FE00] ,Len: 500000
MMCBLK0P2 (DEVINFO) Range: [0XC80000,0XCBFE00] ,Len: 40000
MMCBLK0P3 (RSTINFO) Range: [0XCC0000,0X20BFE00] ,Len: 1400000
MMCBLK0P4 (PROTECT1) Range: [0X20C0000,0X2ABFE00] ,Len: A00000
MMCBLK0P5 (PROTECT2) Range: [0X2AC0000,0X34BFE00] ,Len: A00000
MMCBLK0P6 (SECCFG) Range: [0X34C0000,0X34FFE00] ,Len: 40000
MMCBLK0P7 (LK) Range: [0X3500000,0X355FE00] ,Len: 60000
MMCBLK0P8 (BOOT) Range: [0X3560000,0X455FE00] ,Len: 1000000
MMCBLK0P9 (RECOVERY) Range: [0X4560000,0X595FE00] ,Len: 1400000
MMCBLK0P10 (SECRO) Range: [0X5960000,0X5F5FE00] ,Len: 600000
MMCBLK0P11 (PARA) Range: [0X5F60000,0X625FE00] ,Len: 300000
MMCBLK0P12 (LOGO) Range: [0X6260000,0X6A5FE00] ,Len: 800000
MMCBLK0P13 (CUSTOM) Range: [0X6A60000,0X26A5FE00] ,Len: 20000000
MMCBLK0P14 (EXPDB) Range: [0X26A60000,0X2745FE00] ,Len: A00000
MMCBLK0P15 (TEE1) Range: [0X27460000,0X2795FE00] ,Len: 500000
MMCBLK0P16 (TEE2) Range: [0X27960000,0X27FFFE00] ,Len: 6A0000
MMCBLK0P17 (SYSTEM) Range: [0X28000000,0X87FFFE00] ,Len: 60000000
MMCBLK0P18 (CACHE) Range: [0X88000000,0XA27FFE00] ,Len: 1A800000
MMCBLK0P19 (USERDATA) Range: [0XA2800000,0X746B7FE00] ,Len: 6A4380000
MMCBLK0P20 (FLASHINFO) Range: [0X746B80000,0X747B7FE00] ,Len: 1000000
Done...Presets has been updated...

Done.

PS. версия 32 гигабайта
добавлю pgpt для 16ти гигов

[Dimaster]

Паша, как отвязать от аккаунта аппарат?

[Russib]

Не загружается после замены EMMC
В Recovery заходит, update обновляет, потом висит на логотипе.
родной лог
eMMC Pro - eMMC Programmer Version V1.13
FIRMWARE(0x4D41494E) version:FFFF201712241746
SN:0000000000000000A756B854F877AE2C
+CID:45010053 44573136 47018A4C 3898522A
Manufacturer ID:0x45
Device/BGA:1 (removable:1 BGA:2 POP:3)
OEM/Application ID:0x00
Product name:0x534457313647 (SDW16G)
Product revision:0x01
Product serial number:0x8A4C3898
Manufacturing date:0x52
CRC7 checksum:0x2A
+CSD:D00F0032 0F5903FF FFFFFFEF 8A40401E
CSD structure:0x3
System specification version:0x4
Data read access-time 1:0xF
Data read access-time 2:0x0
Max. bus clock frequency:0x32
Card command classes:0x0F5
Max. read data block length:0x9 (512)
Partial blocks for read allowed:0
Write block misalignment:0
Read block misalignment:0
DSR implemented:0
Device size:0xFFF
Min. read current @ VDD min:0x7
Max. read current @ VDD min:0x7
Min. write current @ VDD min:0x7
Max. write current @ VDD min:0x7
Device size multiplier:0x7
Erase group size:0x1F
Erase group size multiplier:0x1F
Write protect group size:0xF
Write protect group enable:1
Manufacturer default ECC:0
Write speed factor:2
Max. write data block length:0x9
Partial blocks for write allowed:0
Content protection application:0
File format group(R/W):0
Copy flag (OTP)(R/W):1
Permanent write protection(R/W):0
Temporary write protection(R/W):0
File format(R/W):0
ECC code(R/W):0
CRC(R/W):0xF
Not used, always ’1’:0
+EXT_CSD information parsing:
FFU features:0x00
BOOT_SIZE_MULTI[226]:0x20
HC_ERASE_GRP_SIZE[224]:0x01
ERASE_TIMEOUT_MULT[223]:0x03
SEC_COUNT(EXT_CSD[215:212]:0x01D5A000)
CARD_TYPE(EXT_CSD[196]):0x57
CSD_STRUCTURE(EXT_CSD[194]):0x02
EXT_CSD_REV(EXT_CSD[192]):0x07
PARTITION_CONFIG[179]:0x00
Device not boot enabled (default)
BOOT_CONFIG_PROT[178]:0x00
BOOT_BUS_CONDITIONS[177]:0x00
ERASE_GROUP_DEF[175]:0x00
BOOT_WP[173]:0x00
USER_WP[171]:0x80
FW_CONFIG[169]:0x00
RPMB_SIZE_MULT[168]:0x20
WR_REL_SET[167]:0x1F
WR_REL_PARAM[166]:0x05
SANITIZE_START[165]:0x00
BKOPS_START[164]:0x00
BKOPS_EN[163]:0x00
RST_n_FUNCTION[162]:0x01
HPI_MGMT[161]:0x00
PARTITIONING_SUPPORT[160]:0x07
MAX_ENH_SIZE_MULT[159:157]:0x000375
PARTITIONS_ATTRIBUTE[156]:0x00
PARTITION_SETTING_COMPLETED[155]:0x00
GP_SIZE_MULT[154:143]:0x000000000000000000000000
ENH_SIZE_MULT[142:140]:0x000000
ENH_START_ADDR[139:136]:0x00000000
SEC_BAD_BLK_MGMNT[134]:0x00
PRODUCTION_STATE_AWARENESS[133]:0x00
TCASE_SUPPORT[132]:0x00
PERIODIC_WAKEUP[131]:0x00
PROGRAM_CID_CSD_DDR_SUPPORT[130]:0x01
NATIVE_SECTOR_SIZE[63]:0x00
USE_NATIVE_SECTOR[62]:0x00
DATA_SECTOR_SIZE[61]:0x00
INI_TIMEOUT_EMU[60]:0x0A
Class6_CTRL[59]:0x00
DYNCAP_NEEDED[58]:0x00
EXCEPTION_EVENTS_CTRL[57:56]:0x00
EXCEPTION_EVENTS_STATUS[55:54]:0x00
EXT_PARTITIONS_ATTRIBUTE[53:52]:0x00
CONTEXT_CONF[51:37]:0x000000000000000000000000000000
PACKED_COMMAND_STATUS[36]:0x00
PACKED_FAILURE_INDEX[35]:0x00
POWER_OFF_NOTIFICATION[34]:0x00
CACHE_CTRL[33]:0x00
FLUSH_CACHE[32]:0x00
MODE_CONFIG[30]:0x00
MODE_OPERATION_CODES[29]:0x00
FFU_STATUS[26]:0x00
PRE_LOADING_DATA_SIZE[25:22]:0x00000000
MAX_PRE_LOADING_DATA_SIZE[21:18]:0x00
PRODUCT_STATE_AWARENESS_ENABLEMENT[17]:0x02
SECURE_REMOVAL_TYPE[16]:0x09
Basic Information:
Extended CSD revision:
User Data Area Size: 15028MB(0x3AB400000)
Boot Partition Size: 4096KB
RPMB Size: 4096KB
General Purpose Partition 1 Size: 0KB
General Purpose Partition 2 Size: 0KB
General Purpose Partition 3 Size: 0KB
General Purpose Partition 4 Size: 0KB
Erase group size: 512KB

Лог с другой EMMC

eMMC Pro - eMMC Programmer Version V1.13
FIRMWARE(0x4D41494E) version:FFFF201712241746
SN:0000000000000000A756B854F877AE2C
+CID:45010053 454D3332 4728F0DB 7559B0A6
Manufacturer ID:0x45
Device/BGA:1 (removable:1 BGA:2 POP:3)
OEM/Application ID:0x00
Product name:0x53454D333247 (SEM32G)
Product revision:0x28
Product serial number:0xF0DB7559
Manufacturing date:0xB0
CRC7 checksum:0xA6
+CSD:D00F0032 0F5903FF FFFFFFFF 8A40407E
CSD structure:0x3
System specification version:0x4
Data read access-time 1:0xF
Data read access-time 2:0x0
Max. bus clock frequency:0x32
Card command classes:0x0F5
Max. read data block length:0x9 (512)
Partial blocks for read allowed:0
Write block misalignment:0
Read block misalignment:0
DSR implemented:0
Device size:0xFFF
Min. read current @ VDD min:0x7
Max. read current @ VDD min:0x7
Min. write current @ VDD min:0x7
Max. write current @ VDD min:0x7
Device size multiplier:0x7
Erase group size:0x1F
Erase group size multiplier:0x1F
Write protect group size:0x1F
Write protect group enable:1
Manufacturer default ECC:0
Write speed factor:2
Max. write data block length:0x9
Partial blocks for write allowed:0
Content protection application:0
File format group(R/W):0
Copy flag (OTP)(R/W):1
Permanent write protection(R/W):0
Temporary write protection(R/W):0
File format(R/W):0
ECC code(R/W):0
CRC(R/W):0x3F
Not used, always ’1’:0
+EXT_CSD information parsing:
FFU features:0x00
BOOT_SIZE_MULTI[226]:0x20
HC_ERASE_GRP_SIZE[224]:0x04
ERASE_TIMEOUT_MULT[223]:0x0E
SEC_COUNT(EXT_CSD[215:212]:0x03A3E000)
CARD_TYPE(EXT_CSD[196]):0x07
CSD_STRUCTURE(EXT_CSD[194]):0x02
EXT_CSD_REV(EXT_CSD[192]):0x06
PARTITION_CONFIG[179]:0x48
Boot partition 1 enabled for boot
BOOT_CONFIG_PROT[178]:0x00
BOOT_BUS_CONDITIONS[177]:0x00
ERASE_GROUP_DEF[175]:0x00
BOOT_WP[173]:0x00
USER_WP[171]:0x00
FW_CONFIG[169]:0x00
RPMB_SIZE_MULT[168]:0x20
WR_REL_SET[167]:0x1F
WR_REL_PARAM[166]:0x05
SANITIZE_START[165]:0x00
BKOPS_START[164]:0x00
BKOPS_EN[163]:0x01
RST_n_FUNCTION[162]:0x01
HPI_MGMT[161]:0x00
PARTITIONING_SUPPORT[160]:0x01
MAX_ENH_SIZE_MULT[159:157]:0x0000E8
PARTITIONS_ATTRIBUTE[156]:0x00
PARTITION_SETTING_COMPLETED[155]:0x00
GP_SIZE_MULT[154:143]:0x000000000000000000000000
ENH_SIZE_MULT[142:140]:0x000000
ENH_START_ADDR[139:136]:0x00000000
SEC_BAD_BLK_MGMNT[134]:0x00
PRODUCTION_STATE_AWARENESS[133]:0x00
TCASE_SUPPORT[132]:0x00
PERIODIC_WAKEUP[131]:0x00
PROGRAM_CID_CSD_DDR_SUPPORT[130]:0x01
NATIVE_SECTOR_SIZE[63]:0x00
USE_NATIVE_SECTOR[62]:0x00
DATA_SECTOR_SIZE[61]:0x00
INI_TIMEOUT_EMU[60]:0x00
Class6_CTRL[59]:0x00
DYNCAP_NEEDED[58]:0x00
EXCEPTION_EVENTS_CTRL[57:56]:0x00
EXCEPTION_EVENTS_STATUS[55:54]:0x00
EXT_PARTITIONS_ATTRIBUTE[53:52]:0x00
CONTEXT_CONF[51:37]:0x000000000000000000000000000000
PACKED_COMMAND_STATUS[36]:0x00
PACKED_FAILURE_INDEX[35]:0x00
POWER_OFF_NOTIFICATION[34]:0x00
CACHE_CTRL[33]:0x00
FLUSH_CACHE[32]:0x00
MODE_CONFIG[30]:0x00
MODE_OPERATION_CODES[29]:0x00
FFU_STATUS[26]:0x00
PRE_LOADING_DATA_SIZE[25:22]:0x00000000
MAX_PRE_LOADING_DATA_SIZE[21:18]:0x00
PRODUCT_STATE_AWARENESS_ENABLEMENT[17]:0x00
SECURE_REMOVAL_TYPE[16]:0x00
Basic Information:
Extended CSD revision: Revision 1.6 (eMMC v4.5)
User Data Area Size: 29820MB(0x747C00000)
Boot Partition Size: 4096KB
RPMB Size: 4096KB
General Purpose Partition 1 Size: 0KB
General Purpose Partition 2 Size: 0KB
General Purpose Partition 3 Size: 0KB
General Purpose Partition 4 Size: 0KB
Erase group size: 512KB

Порядок действий был такой:
BOOT1 и BOOT2 я со своей памяти зашил.
Разделы тоже со своей, за исключением custom и дальше из дампа в теме, а flashinfo почему то решил не зашивать

Поставил kmv3w000lm-b310, теперь обновиться не могу Firmware corrupt