Motorola XT1063 нужна помощь

[SVH]

Есть Motorola XT1063 убитая софтово

Подпаялся к ISP


12:09:23 : ================================================== ====
12:09:23 : ================================================== ====
12:09:23 : eMMC Test Point Connection Module
12:09:23 : ================================================== ====
12:09:23 : ================================================== ====
12:09:23 :
12:09:23 : 1. DO NOT USE THE PHONE"S BATTERY
12:09:23 : 2. Connect the Soldered TP Connections to ATF Box
12:09:23 : 3. Disconnect the USB Cable and Wait until the
12:09:23 : the ATF Software will tell you to Connect the USB.
12:09:23 :
12:09:23 :
12:09:23 : Interface Reset OK!
12:09:23 : eMMC Access Type: SECTOR MODE
12:09:23 : eMMC Supported Voltage Range:
12:09:23 : 3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V
12:09:23 :
12:09:23 : CID : 45010053454D3038470743AFE1B0510F
12:09:23 : CSD : D00F00320F5903FFFFFFFFFF8A40407F
12:09:23 :
12:09:23 : eMMC Boot Information
12:09:23 : Revision 1.6 (for MMC v4.5, v4.51)
12:09:23 : BOOT PARTITION : USER AREA
12:09:23 : PARTITION ACCESS : R/W USER PARTITION
12:09:23 : PERM_BOOT_CFG_PROT : DISABLED
12:09:23 : PWR_BOOT_CFG_PROT : DISABLED
12:09:23 : BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
12:09:23 : RESET BUS WIDTH : ENABLED
12:09:23 : eMMC FirmW UPDATE : DISABLED
12:09:23 : EMMC CACHE SIZE : 0 KB
12:09:23 : SUPER PAGE SIZE : 4096 KB
12:09:23 : HC ERASE GROUP SIZE: 512 KB
12:09:23 : USER AREA SIZE : 7818182656 BYTES
12:09:23 : BOOT PARTITION SIZE: 2048 KB
12:09:23 : RPMB PARTITION SIZE: 2048 KB
12:09:23 :
12:09:23 :
12:09:23 : eMMC Device Information
12:09:23 : Manufacturer ID: SANDISK
12:09:23 : Device Type : Embedded BGA
12:09:23 : Application ID : 00
12:09:23 : Product Name : SEM08G
12:09:23 : Product Rev : 0.7
12:09:23 : Product SN : 43AFE1B0
12:09:23 : Manufactured : January 1998
12:09:23 :
12:09:23 : Card Specific Data
12:09:23 : CSD_STRUCTURE : Extended
12:09:23 : SPEC_VERS : Version 4.1/4.2/4.3
12:09:23 : TAAC : 3 ns
12:09:23 : TRAN_SPEED : 4000000 KHz
12:09:23 : READ_BL_LEN : 512 Bytes
12:09:23 : C_SIZE : HIGH CAPACITY
12:09:23 : WP_GRP_ENABLE : YES
12:09:23 : WRITE_BL_LEN : 512 Bytes
12:09:23 : CONTENT_PROT_APP : NO
12:09:23 : PERM_WRITE_PROTECT: NO
12:09:23 : TMP_WRITE_PROTECT : NO
12:09:23 :
12:09:23 : Extended CSD Saved:
12:09:23 : 45010053454D3038470743AFE1B0510F.ext_csd
12:09:23 : Backup Directory:
12:09:23 : D:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\
12:09:23 :


Так как на поддержке ничего нет, нашел repair pack от Easy Jtag


залил EMMC_ROM1_00000000_20000000.bin как UserArea (536Mb)
залил EMMC_ROM2_00000000_00400000.bin как Boot1 (4Mb)
залил EMMC_ROM3_00000000_00400000.bin как Boot2 (4Mb)
еще заливал ext_csd как новый, так и с бэкапа

В результате без изменений
Системой видится как HS-USB QDLoader 9008

Подскажите что я делаю не так, и важна ли очередность заливки ext_csd?

Спасибо

Thanx

[Dimaster]

http://www.mcrf.ru/forum/showpost.php?p=304251&postcount=3


.:: Скрытый текст (вы должны войти под своим логином или зарегистрироваться и иметь 20 сообщение(ий)) ::.

[SVH]

Пролил


================================================== ====
================================================== ====
eMMC Test Point Connection Module
================================================== ====
================================================== ====

1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.


Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V

CID : 45010053454D3038470743AFE1B0510F
CSD : D00F00320F5903FFFFFFFFFF8A40407F

eMMC Boot Information
Revision 1.6 (for MMC v4.5, v4.51)
BOOT PARTITION : USER AREA
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 0 KB
SUPER PAGE SIZE : 4096 KB
HC ERASE GROUP SIZE: 512 KB
USER AREA SIZE : 7818182656 BYTES
BOOT PARTITION SIZE: 2048 KB
RPMB PARTITION SIZE: 2048 KB


eMMC Device Information
Manufacturer ID: SANDISK
Device Type : Embedded BGA
Application ID : 00
Product Name : SEM08G
Product Rev : 0.7
Product SN : 43AFE1B0
Manufactured : January 1998

Card Specific Data
CSD_STRUCTURE : Extended
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 3 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO

Extended CSD Saved:
45010053454D3038470743AFE1B0510F.ext_csd
Backup Directory:
D:\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\

Start Writing 0x00100000 Blocks at 0x00000000
Partition Selected: USER AREA

Total Elapsed Time 00:14:47
Write Success!


Все так же HS-USB QDLoader 9008

[Dimaster]

Не понимаю конечно я лог ATF Box у Вас, вроде криминального ничего не вижу. Должен быть старт от этого фулла, смещений нет. Посмотрите питания на еММС может не доходят(тоже болтаться на 9008 будет), контроллер питания у них дохловатенький, доводилось тоже менять. Попробуйте память другую вкинуть.

[Verlaten]

такая же проблема,единственное смутило питалово на флешку 2.9v разве не должно быть 3.3
фулл лил z3x тело не включилось
у когото получилось подннять?
http://s017.radikal.ru/i417/1609/18/7160cb56577f.jpg (http://radikal.ru)

[Diablosss]

Тоже самое.
тело убито софтово. фулл не помог. остался на 9008
:vis: