next
07.05.2016, 12:38
День добрый.
Предыстория аппарата со слов клиента:
Разблокировал загрузчик
Установил cwm и прошил superSu.
Из перезагрузки аппарат не вышел.
Потребление при нажатии на кнопку включения 170ma.
Подпаялся на плате к флешке. Прошил ему с саппорта rom1, rom2 , rom3 и extscd. Через вкладку "write all eMMC reqions at once.
лог:
Z3X EasyJtag Software ver. 2.0.8.3
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 05050E0A1DF1F7D5, ,FW Ver.: 01.52
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 90014A4834473164048502A20D6EB0A4
EMMC CSD : D02701320F5903FFFFFFFFE78A4040E2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 11/2013 Rev.0x85
EMMC NAME: <b>H4G1d </b> , S/N: 44174702
EMMC NAME (HEX): 48344731642000
EMMC ROM1 (Main User Data) Capacity: 3696 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 2048 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G1d _ 44174702_20160507_1157.extcsd
Searching for partition tables...
Detected MBR...
Disk Signature: 00000000
MMCBLK0P0 Type: Unknown:0x4d Start: 200 Len: 5000
MMCBLK0P1 Type: Unknown:0x45 Start: 5200 Len: 88000
MMCBLK0P2 Type: Unknown:0x46 Start: 8D200 Len: 465000
MMCBLK0P3 Type: Extended Start: 4F2200 Len: E6B0DC00
Warning: Extended Partition Detected - this feature not tested
MMCBLK0P4 Type: Unknown:0x49 Start: 4F2400 Len: 1D4C000
MMCBLK0P5 Type: Unknown:0x50 Start: 223E600 Len: C35000
Done.
Z3X EasyJtag Software ver. 2.0.8.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
Input file : C:\Program Files\Z3X\EASYJTAG\Repair Files\Новая папка\USER_AREA_512MB.bin_0x00000000_0x000FFF FF.bin
Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 2169 kB/s
Z3X EasyJtag Software ver. 2.0.8.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
Input file : C:\Program Files\Z3X\EASYJTAG\Repair Files\Новая папка\Boot1_2MB.bin_0x00000000_0x00001000.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 867 kB/s
Z3X EasyJtag Software ver. 2.0.8.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
Input file : C:\Program Files\Z3X\EASYJTAG\Repair Files\Новая папка\Boot2_2MB.bin_0x00000000_0x00001000.bin
Writing 0000200000 bytes to 00000000 ...ROM3 (BOOT2 ROM)
Done. Write Speed: 861 kB/s
Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.0.8.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
Writing...
Done.
Z3X EasyJtag Software ver. 2.0.8.3
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 05050E0A1DF1F7D5, ,FW Ver.: 01.52
CMD Pullup Level:1670 mV
CMD Active Level:2258 mV
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 90014A4834473164048502A20D6EB0A4
EMMC CSD : D02701320F5903FFFFFFFFE78A4040E2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 11/2013 Rev.0x85
EMMC NAME: <b>H4G1d </b> , S/N: 44174702
EMMC NAME (HEX): 48344731642000
EMMC ROM1 (Main User Data) Capacity: 3696 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 2048 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G1d _ 44174702_20160507_1206.extcsd
Searching for partition tables...
Detected MBR...
Disk Signature: 00000000
MMCBLK0P0 Type: Unknown:0x4d Start: 200 Len: 5000
MMCBLK0P1 Type: Unknown:0x45 Start: 5200 Len: 88000
MMCBLK0P2 Type: Unknown:0x46 Start: 8D200 Len: 465000
MMCBLK0P3 Type: Extended Start: 4F2200 Len: E6B0DC00
Warning: Extended Partition Detected - this feature not tested
MMCBLK0P4 Type: Unknown:0x49 Start: 4F2400 Len: 1D4C000
MMCBLK0P5 Type: Unknown:0x50 Start: 223E600 Len: C35000
Done.
Аппарат так же не включается и не входит в режим прошивки.
Флешь полностью не стирал.
Подскажите что не так делаю?
Предыстория аппарата со слов клиента:
Разблокировал загрузчик
Установил cwm и прошил superSu.
Из перезагрузки аппарат не вышел.
Потребление при нажатии на кнопку включения 170ma.
Подпаялся на плате к флешке. Прошил ему с саппорта rom1, rom2 , rom3 и extscd. Через вкладку "write all eMMC reqions at once.
лог:
Z3X EasyJtag Software ver. 2.0.8.3
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 05050E0A1DF1F7D5, ,FW Ver.: 01.52
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 90014A4834473164048502A20D6EB0A4
EMMC CSD : D02701320F5903FFFFFFFFE78A4040E2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 11/2013 Rev.0x85
EMMC NAME: <b>H4G1d </b> , S/N: 44174702
EMMC NAME (HEX): 48344731642000
EMMC ROM1 (Main User Data) Capacity: 3696 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 2048 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G1d _ 44174702_20160507_1157.extcsd
Searching for partition tables...
Detected MBR...
Disk Signature: 00000000
MMCBLK0P0 Type: Unknown:0x4d Start: 200 Len: 5000
MMCBLK0P1 Type: Unknown:0x45 Start: 5200 Len: 88000
MMCBLK0P2 Type: Unknown:0x46 Start: 8D200 Len: 465000
MMCBLK0P3 Type: Extended Start: 4F2200 Len: E6B0DC00
Warning: Extended Partition Detected - this feature not tested
MMCBLK0P4 Type: Unknown:0x49 Start: 4F2400 Len: 1D4C000
MMCBLK0P5 Type: Unknown:0x50 Start: 223E600 Len: C35000
Done.
Z3X EasyJtag Software ver. 2.0.8.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
Input file : C:\Program Files\Z3X\EASYJTAG\Repair Files\Новая папка\USER_AREA_512MB.bin_0x00000000_0x000FFF FF.bin
Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 2169 kB/s
Z3X EasyJtag Software ver. 2.0.8.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
Input file : C:\Program Files\Z3X\EASYJTAG\Repair Files\Новая папка\Boot1_2MB.bin_0x00000000_0x00001000.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 867 kB/s
Z3X EasyJtag Software ver. 2.0.8.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
Input file : C:\Program Files\Z3X\EASYJTAG\Repair Files\Новая папка\Boot2_2MB.bin_0x00000000_0x00001000.bin
Writing 0000200000 bytes to 00000000 ...ROM3 (BOOT2 ROM)
Done. Write Speed: 861 kB/s
Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.0.8.3
Skip loading eMMC Addon Firmware
CMD Pullup Level:1660 mV
CMD Active Level:2258 mV
Writing...
Done.
Z3X EasyJtag Software ver. 2.0.8.3
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 05050E0A1DF1F7D5, ,FW Ver.: 01.52
CMD Pullup Level:1670 mV
CMD Active Level:2258 mV
HiPower™ mode is ON!
eMMC Device Information
EMMC CID : 90014A4834473164048502A20D6EB0A4
EMMC CSD : D02701320F5903FFFFFFFFE78A4040E2
EMMC Manufacturer ID: 0090 , OEM ID: 014A
EMMC Date: 11/2013 Rev.0x85
EMMC NAME: <b>H4G1d </b> , S/N: 44174702
EMMC NAME (HEX): 48344731642000
EMMC ROM1 (Main User Data) Capacity: 3696 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 2048 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00]
Partitioning Support [PARTITIONING_SUPPORT]: 0x03
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G1d _ 44174702_20160507_1206.extcsd
Searching for partition tables...
Detected MBR...
Disk Signature: 00000000
MMCBLK0P0 Type: Unknown:0x4d Start: 200 Len: 5000
MMCBLK0P1 Type: Unknown:0x45 Start: 5200 Len: 88000
MMCBLK0P2 Type: Unknown:0x46 Start: 8D200 Len: 465000
MMCBLK0P3 Type: Extended Start: 4F2200 Len: E6B0DC00
Warning: Extended Partition Detected - this feature not tested
MMCBLK0P4 Type: Unknown:0x49 Start: 4F2400 Len: 1D4C000
MMCBLK0P5 Type: Unknown:0x50 Start: 223E600 Len: C35000
Done.
Аппарат так же не включается и не входит в режим прошивки.
Флешь полностью не стирал.
Подскажите что не так делаю?