Просмотр полной версии : CM2 SPD Тест и логи удачных операций
В этой теме собираем логи удачных и не удачных операций CM2 SPD.
MobilaGSM
06.01.2016, 20:59
Micromax X2050
"]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Elapsed: 00:00:14
Reconnect Power/Cable!
"]1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Check data ...
Reading NV ...
Saved to : D:\InfinityBox\CM2SPD\phdata\backup\MICROMAX_X2050 _ 6531_NV_00008000.nv
Elapsed: 00:01:13
Reconnect Power/Cable!
"]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Read Flash Content
Read Ok , collect info
Set FileInfo :
Model Vendor : MICROMAX
Model Name : X2050 BY MOBILAGSM.RU
ExtInfo Data : RU,EN
Saved to : D:\InfinityBox\CM2SPD\Read_out\SPD6531_00400000_GD 25LQ32_RU,EN__MICROMAX-X2050 BY MOBILAGSM.RU.bin
Done!
Elapsed: 00:00:54
Reconnect Power/Cable!
"]1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Check data... Can take some time
User Code : 12345678
Done!
Elapsed: 00:00:29
Reconnect Power/Cable!
правка IMEI"]1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Process can take some time, please, wait
Init ok, send data
Write done!
Elapsed: 00:00:12
Reconnect Power/Cable!
"]Settings : SmartFormat is On
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!
Elapsed: 00:00:15
Reconnect Power/Cable!
после формата user code ушел, imei на месте ... все ок.
MobilaGSM
14.01.2016, 09:20
ZTE Blade AF3
"]1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7730/7731 eMMC Loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FLASH : eMMC Flash , Structure : Ok!
Reading extended info ...
Model Name : P731A20
Model Brand : ZTE
Model Device: P731A20
AndrVersion : 4.4.2
BaseBand CPU: SP7731GEA
CompileDate : 1437035828
Project Ver : DIS_RU_QB18D_P731A20V1.0.1
Model Ext : ZTE T221
ExtraInfo : HWInfo not exists, normal phone
ExtraInfo : GSM Phone
Elapsed: 00:00:14
Reconnect Power/Cable!
"]Loading : Blade_AF3_FPT_S500__V01_m02.pac
CRVersion : BP_R1.0.0
PacCPUinfo : SC7731_2341A
PacVersion : Blade_AF3_FPT_S500__V01_m02
FastCheck : 0x36C2723C
Loading files ...
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : wmodem.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : logo_kernel.bmp
File : logo_uboot.bmp
File : cache.img
File : u-boot.bin
File : SC7731_2341A.xml
Load Ok!
Operation : Flash [ v1.12 ]
======= Flash
Files set for flashing :
[ MCU ] : Blade_AF3_FPT_S500__V01_m02.pac
CRVersion : BP_R1.0.0
PacCPUinfo : SC7731_2341A
PacVersion : Blade_AF3_FPT_S500__V01_m02
File : fdl1.bin
File : fdl2.bin
File : nvitem.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : wmodem.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : logo_kernel.bmp
File : logo_uboot.bmp
File : cache.img
File : u-boot.bin
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
PMTManager : Load 0x17 records
PMTManager : PMT Update Ok!
Flashing now
[FlashProc] : CODE
Current ID : PRODNV
Current File : prodnv.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!
[FlashProc] : BOOTCODE
Current ID : SPLLOADER
Current File : u-boot-spl-16k.bin
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : MODEM_W
Current File : wmodem.bin
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : DSP_W
Current File : DSP_DM_G2.bin
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : MODEM_WCN
Current File : SC8800G_x30g_wcn_dts_modem.bin
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : BOOT
Current File : boot.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : RECOVERY
Current File : recovery.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : USERDATA
Current File : userdata.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : BOOTLOGO
Current File : logo_kernel.bmp
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : FASTBOOT_LOGO
Current File : logo_uboot.bmp
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : FLASH
Current Part : wruntimenv1
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : FLASH_WCN
Current Part : wcnruntimenv1
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : CACHE
Current File : cache.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : ERASEMISC
Current Part : misc
[FlashProc] : Ok!
[FlashProc] : BOOTCODE
Current ID : UBOOTLOADER
Current File : u-boot.bin
Flashing now ...
[FlashProc] : Ok!
Elapsed: 00:03:01
Reconnect Power/Cable!
"]Operation : Read NV [ v1.12 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 38 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7730/7731 eMMC Loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected eMMC Flash , Structure detect Ok!
Read NVM Part #1
Part Ok
Read NVM Part #2
Part Ok
Saved to : D:\InfinityBox\CM2SPD\phdata\backup\ZTE_BLADE_AF3_ CX_SPDNV.spdnv
Elapsed: 00:00:31
Reconnect Power/Cable!
Висел на заставле ZTE, Wipe из recovery, Format File System через CM2SPD результата не дали.
Прошивка через CM2SPD > Flash и аппарат живой, IMEI на месте. :poz:
.:: Скрытый текст (вы должны войти под своим логином или зарегистрироваться и иметь 10 сообщение(ий)) ::.
Dr_Wolodya
30.01.2016, 05:07
Тоже попался ZTE T221 (AF3)
"]Operation : Read FullFlash [ v1.13 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7730/7731 eMMC Loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Step #1 Passed!
[FW_READER] : Step #2 Passed!
[FW_READER] : Step #3 Passed!
Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7730/7731 eMMC Loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name : P731A20
Model Brand : ZTE
Model Device: P731A20
AndrVersion : 4.4.2
BaseBand CPU: SP7731GEA
Project Ver : DIS_RU_QB18D_P731A20V1.0.1
Model Ext : ZTE T221
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_14D_W15.22_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x800.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : userdata.img
Firmware Size : 1199 MiB
Saved to : C:\InfinityBox\CM2SPD\Read_out\SP7731GEA_P731A20_4 .4.2_DIS_RU_QB18D_P731A20V1.0.1\
Done!
Elapsed: 00:11:30
Reconnect Power/Cable!
"]Operation : Read NV [ v1.13 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7730/7731 eMMC Loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected eMMC Flash , Structure detect Ok!
Read NVM Part #1
Part Ok
Read NVM Part #2
Part Ok
Saved to : C:\InfinityBox\CM2SPD\Flash\ZTE T221 AF3\CX_SPDNV.spdnv
Elapsed: 00:00:52
Reconnect Power/Cable!
"]Operation : Read PhoneBook [ v1.13 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7730/7731 eMMC Loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!
Mount : /data
Size : 0x00000000934FB000
Step #1
Step #2
Read Ok, PhoneBook records extracted : 26
TXT Saved to : C:\Users\user\Desktop\SPD_PhoneBook.txt
Write : 26
CSV Saved to : C:\Users\user\Desktop\SPD_PhoneBook.csv
Write : 26
VCF Saved to : C:\Users\user\Desktop\SPD_PhoneBook.vcf
Write : 26
VCFv3 Saved to : C:\Users\user\Desktop\SPD_PhoneBook_v3.vcf
Elapsed: 00:00:18
Reconnect Power/Cable!
"]Operation : Format File System [ v1.13 ]
Settings : SmartFormat is On
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 31 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7730/7731 eMMC Loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!
eMMC phone detected! Will use 'Safe Format' mode!
Mount : /data
Size : 0x00000000934FB000
State : 0x0001
Mount : /cache
Size : 0x0000000009600000
State : 0x0001
Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!
Done!
Elapsed: 00:00:15
Reconnect Power/Cable!
fly ts91 сброс кодов, отчично
Start at : [29.01.2016 / 12:52:28]
Operation : Format File System [ v1.12 ]
Settings : SmartFormat is On
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 69 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2 Boot Ok
CPU ID : 6531 , FDLStat : 0000
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Verify data... Can take some time
Init Ok, formatting DIN area ...
Format Block Done!
Done!
ZTE Blade A3 (T220)
Unlock:
Start at : [29.01.2016 / 9:06:18]
Operation : SP Unlock [ v1.13 ]
Mode : DirectUnlock
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 eMMC loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected eMMC Flash , Structure detect Ok!
Checking Structure ...
SimLock state : Locked!
Unlocking ...
Unlock Done!
Elapsed: 00:00:15
Reconnect Power/Cable!
Read FullFlash:
Start at : [29.01.2016 / 9:08:14]
Operation : Read FullFlash [ v1.13 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 eMMC loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Step #1 Passed!
[FW_READER] : Step #2 Passed!
[FW_READER] : Step #3 Passed!
Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 eMMC loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name : P172R12
Model Brand : ZTE
Model Device: P172R12
AndrVersion : 4.4.2
BaseBand CPU: SCX15_SP7715EA
Project Ver : MGF_RU_QB18D_P172R12V1.0.2
Model Ext : ZTE T220
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : nvitem_w.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : sc7715_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : CP2._CP2_WCN_14C_W14.51_Release.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x800.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : userdata.img
Firmware Size : 1198 MiB
Saved to : E:\ZTE_Blade_A3_(SC7715)\SCX15_SP7715EA_P172R12_4. 4.2_MGF_RU_QB18D_P172R12V1.0.2\
Done!
Elapsed: 00:19:52
Reconnect Power/Cable!
Finish at : [29.01.2016 / 9:28:07]
ZTE Blade A3 (T220)
Unlock:
Start at : [29.01.2016 / 9:06:18]
Operation : SP Unlock [ v1.13 ]
Mode : DirectUnlock
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 eMMC loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected eMMC Flash , Structure detect Ok!
Checking Structure ...
SimLock state : Locked!
Unlocking ...
Unlock Done!
Elapsed: 00:00:15
Reconnect Power/Cable!
Read FullFlash:
Start at : [29.01.2016 / 9:08:14]
Operation : Read FullFlash [ v1.13 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 eMMC loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Step #1 Passed!
[FW_READER] : Step #2 Passed!
[FW_READER] : Step #3 Passed!
Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 eMMC loader v1.1 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name : P172R12
Model Brand : ZTE
Model Device: P172R12
AndrVersion : 4.4.2
BaseBand CPU: SCX15_SP7715EA
Project Ver : MGF_RU_QB18D_P172R12V1.0.2
Model Ext : ZTE T220
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : nvitem_w.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : sc7715_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : CP2._CP2_WCN_14C_W14.51_Release.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x800.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : userdata.img
Firmware Size : 1198 MiB
Saved to : E:\ZTE_Blade_A3_(SC7715)\SCX15_SP7715EA_P172R12_4. 4.2_MGF_RU_QB18D_P172R12V1.0.2\
Done!
Elapsed: 00:19:52
Reconnect Power/Cable!
Finish at : [29.01.2016 / 9:28:07]
А3 от чего разлачивали? если от мегафона, то там только обновить по wifi надо было и все
А3 от чего разлачивали? если от мегафона, то там только обновить по wifi надо было и все
Да от Мегафона. Сначала обновился, но не помогло.
Да от Мегафона. Сначала обновился, но не помогло.
Странно, сколько продали А3, все разлочились при обновлении, помой му с 1.01 до 1.02. А обе симки работают и 2 вопрос, сброс делали? Просто с микромаксами это не прокатило
Странно, сколько продали А3, все разлочились при обновлении, помой му с 1.01 до 1.02. А обе симки работают и 2 вопрос, сброс делали? Просто с микромаксами это не прокатило
Вот сброс не делал, в этом видимо моя ошибка.
Ну и ладно. Разлок с помощью CM2SPD занял 15 секунд. Все таки быстрее, чем по обновление по воздуху и hard reset.
Перманентный там разлок. Ничего не слетит. Не стоит собирать MTK и SPD в кучу, там совершенно разные реализации.
Dr_Wolodya
04.03.2016, 13:05
Lenovo A238t, CPU: Spreadtrum SC8830, Flash: NAND (block 256 Kb).
Operation : Check/Read Info [ v1.15 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 569 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC8830 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FLASH : NAND Flash , Structure : Ok!
Reading extended info ...
Model Name : A238t
Model Brand : Lenovo
Model Device: A238t
AndrVersion : 2.3.5
BaseBand CPU: SP8830GA
CompileDate : 07.07.2014 3:17:46
Project Ver : MDroid2.3.5
Model Ext : Lenovo A238t
ExtraInfo : HWInfo not exists, normal phone
ExtraInfo : TDMA Phone
Elapsed: 00:00:49
Reconnect Power/Cable!
Operation : Format File System / Reset Settings [ v1.15 ]
Settings : SmartFormat is On
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 569 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC8830 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Checking Structure ...
Detected NAND Flash , Structure detect Ok!
Formatting NAND Flash
Format UserData
Format Ok!
Format Cache
Format Ok!
Done!
Elapsed: 00:00:17
Reconnect Power/Cable!
Operation : Read NV [ v1.15 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 569 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC8830 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected NAND Flash , Structure detect Ok!
Read NVM Part #1
Part Ok
Read NVM Part #2
Part Ok
Saved to : C:\InfinityBox\CM2SPD\phdata\backup\Lenovo A238t\CX_SPDNV.spdnv
Elapsed: 00:00:34
Reconnect Power/Cable!
Operation : Read NV [ v1.15 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 569 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC8830 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected NAND Flash , Structure detect Ok!
Read NVM Part #1
Part Ok
Read NVM Part #2
Part Ok
Saved to : C:\InfinityBox\CM2SPD\phdata\backup\Lenovo A238t\Gold Copy NV\CX_SPDNV.spdnv
Elapsed: 00:00:36
Reconnect Power/Cable!
Operation : Read FullFlash [ v1.15 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 569 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC8830 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected NAND Flash , Structure detect Ok!
[FW_READER] : Step #1 Passed!
[FW_READER] : Step #2 Passed!
[FW_READER] : Initialize Ok , 0x13 , NAND : b256k
[FW_READER] : Step #3 Passed!
Model Name : A238t
Model Brand : Lenovo
Model Device: A238t
AndrVersion : 2.3.5
BaseBand CPU: SP8830GA
Project Ver : MDroid2.3.5
Model Ext : Lenovo A238t
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv_b256k.img
[Read Ok] : nvitem_td.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : sc8830_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : sc8830_modem_sc8830_cp2.bin
[Read Ok] : logo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system_b256k.img
[Read Ok] : cache_b256k.img
[Read Ok] : recovery.img
[Read Ok] : userdata_b256k.img
AndroidInfo created
Firmware Size : 265 MiB
Saved to : C:\InfinityBox\CM2SPD\phdata\backup\Lenovo A238t\Pac\SP8830GA_[NAND_b256k]_A238t_2.3.5_MDroid2.3.5_Lenovo_A238t\
Done!
Elapsed: 00:18:58
Reconnect Power/Cable!
ogvozdyk
04.03.2016, 22:43
Плпншет MANTA. Пришел с графическим кодом.Все ОК!
.:: Скрытый текст (вы должны войти под своим логином или зарегистрироваться и иметь 1 сообщение(ий)) ::.
.:: Скрытый текст (вы должны войти под своим логином или зарегистрироваться и иметь 1 сообщение(ий)) ::.
.:: Скрытый текст (вы должны войти под своим логином или зарегистрироваться и иметь 1 сообщение(ий)) ::.
ZTE BLADE A5 UNLOCK 15 Секунд
Start at : [15.03.2016 / 19:37:47]
Operation : SP Unlock [ v1.14 ]
Mode : DirectUnlock
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 12 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC773x Android 5.x eMMC v1.0 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected eMMC Flash , Structure detect Ok!
Checking Structure ...
SimLock state : Locked!
Unlocking ...
Unlock Done!
Elapsed: 00:00:15
Reconnect Power/Cable!
Finish at : [15.03.2016 / 19:38:02]
Добавлено через 18 минут
Alcatel OneTouch 4024D PIXI FIRST Прошивка
Operation : Read FullFlash [ v1.15 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 23 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC773x Android 5.x eMMC v1.0 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!
[FW_READER] : Step #1 Passed!
[FW_READER] : Step #2 Passed!
[FW_READER] : Step #3 Passed!
Phone found! [ 23 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC773x Android 5.x eMMC v1.0 Inf
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Model Name : ALCATEL_ONETOUCH_4024D
Model Brand : TCL
Model Device: ALCATEL_ONETOUCH_4024D
AndrVersion : 4.4.2
BaseBand CPU: SP7731GEA_18045
Project Ver : 4024D_RU_AL_V1.8_150921
Model Ext : 4024D
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731g_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc7731g_modem_CP2_WCN_14E_W15.31.1_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x800.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : recovery.img
[Read Ok] : userdata.img
AndroidInfo created
Firmware Size : 1242 MiB
Saved to : C:\Users\botir\Desktop\SP7731GEA_18045_ALCATEL_ONE TOUCH_4024D_4.4.2_4024D_RU_AL_V1.8_150921_4024D\
Done!
Dr_Wolodya
19.03.2016, 04:50
Alcatel OT-1060 (Orange Riga) SPD6531
"]Operation : Read FullFlash [ v1.16 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0000
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Read Flash Content
Read Ok , collect info
Set FileInfo :
Model Vendor : Alcatel
Model Name : 1060
ExtInfo Data : Eng_Ita
Saved to : C:\InfinityBox\CM2SPD\Read_out\SPD6531_00400000_GD 25LQ32_Eng_Ita__Alcatel-1060.bin
Done!
Elapsed: 00:00:36
Reconnect Power/Cable!
"]Operation : Read NV [ v1.16 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0000
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Check data ...
Reading NV ...
Saved to : D:\Mobile\Alcatel\1060 (Orange Riga)\cm2\nv\6531_NV_00008000.nv
Elapsed: 00:00:23
Reconnect Power/Cable!
Micromax x2050 spd 6531
Operation : Read FullFlash
Phone found! [ 12 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Read Flash Content
Read Ok , collect info
Set FileInfo :
Model Vendor : micromax
Model Name : x2050
ExtInfo Data : rus
Saved to : C:\InfinityBox\CM2SPD\Read_out\SPD6531_00400000_GD 25LQ32_rus__micromax-x2050.bin
Done!
Elapsed: 00:01:03
Operation : Read NV
Phone found! [ 12 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Check data ...
Reading NV ...
Saved to : C:\InfinityBox\CM2SPD\Read_out\6531_NV_00008000.nv
Elapsed: 00:00:22
Dr_Wolodya
25.03.2016, 19:01
Philips e120 SPD6531
"]Operation : Read NV [ v1.16 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Check data ...
Reading NV ...
Saved to : C:\InfinityBox\CM2SPD\Read_out\6531_NV_00008000.nv
Elapsed: 00:00:32
Reconnect Power/Cable!
"]Operation : Read FullFlash [ v1.16 ]
1. Remove battery. Insert USB cable
2. Press and hold BootKey ( Skip, if use BootCable )
3. Insert battery
==== Wait for phone...
Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Read Flash Content
Read Ok , collect info
Set FileInfo :
Model Vendor : Philips
Model Name : e120
ExtInfo Data : Eng_PL
Saved to : C:\InfinityBox\CM2SPD\Read_out\SPD6531_00400000_GD 25LQ32_Eng_PL__Philips-e120.bin
Done!
Elapsed: 00:00:36
Reconnect Power/Cable!
ARTEL E508 SPD6531
Operation : Read FullFlash
==== Wait for phone...
Phone found! [ 12 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending boot ...
Boot Sent , starting...
Boot Ver : Spreadtrum Boot Block version 1.2
Boot Ok
CPU ID : 6531 , FDLStat : 0100
[0] Flash DIE : 00C8 0060 0016 0000
[0] Flash VEN : GigaDevice , GD25LQ32
[0] Flash CAP : 00400000
Read Flash Content
Read Ok , collect info
Set FileInfo :
Model Vendor : ARTEL
Model Name : E508
ExtInfo Data : RUS,UZBEK
Saved to : C:\InfinityBox\CM2SPD\Read_out\SPD6531_00400000_GD 25LQ32_RUS,UZBEK__ARTEL-E508.bin
Done!
Elapsed: 00:00:52
bigpignik
09.04.2016, 12:33
Phone found! [ 29 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
PMTManager : Load 0x17 records
PMTManager : PMT Update Failed!!!
Flashing now
[FlashProc] : CODE
Current ID : PRODNV
Current File : prodnv.img
Flashing now ...
[FlashProc] : Error with code 0x0003
Elapsed: 00:00:00
Reconnect Power/Cable!
digma tt7021pg была с вирусами,начал check/info софт завис, и все, не вкл ( лог выше при попытке прошить)
процессор sc5735 ( может есть у кого fullflash?)
==== Wait for phone...
Phone found! [ 29 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
PMTManager : Load 0x17 records
PMTManager : PMT Update Ok!
Flashing now
[FlashProc] : CODE
Current ID : PRODNV
Current File : prodnv.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : ERASEUBOOT
Current Part : uboot
[FlashProc] : Ok!
[FlashProc] : BOOTCODE
Current ID : SPLLOADER
Current File : u-boot-spl-16k.bin
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : MODEM_W
Current File : 5735c2_modem_EA.bin
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : DSP_W
Current File : DSP_DM_G2.bin
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : MODEM_WCN
Current File : SC8800G_8830_wcn_modem_EC_zerocopy.bin
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : BOOT
Current File : boot.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : RECOVERY
Current File : recovery.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : SYSTEM
Current File : system.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : USERDATA
Current File : userdata.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : BOOTLOGO
Current File : DM_bootlogo-600x1024_1.bmp
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : CODE
Current ID : FASTBOOT_LOGO
Current File : CU_svga_logo_256.bmp(1)
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : FLASH
Current Part : wruntimenv1
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : FLASH_WCN
Current Part : wcnruntimenv1
[FlashProc] : Ok!
[FlashProc] : IMAGE
Current ID : CACHE
Current File : cache.img
Flashing now ...
[FlashProc] : Ok!
[FlashProc] : ERASE
Current ID : ERASEMISC
Current Part : misc
[FlashProc] : Ok!
[FlashProc] : BOOTCODE
Current ID : UBOOTLOADER
Current File : u-boot.bin
Flashing now ...
[FlashProc] : Ok!
Elapsed: 00:02:27
Reconnect Power/Cable!
прошился без акб, не вклучается, может есть у кого NVRAm ?
mr treexel
09.04.2016, 13:06
На офф сайте же есть Digma_Spreadtrum_IMEI_tool (http://www.ddixlab.com/public/digma/tabletpc/_Tools_Manuals/Digma_Spreadtrum_IMEI_tool.rar) и прошивка с downloadtool
bigpignik
09.04.2016, 13:30
На офф сайте же есть Digma_Spreadtrum_IMEI_tool (http://www.ddixlab.com/public/digma/tabletpc/_Tools_Manuals/Digma_Spreadtrum_IMEI_tool.rar) и прошивка с downloadtool
прошивка то идет а он не вкл, imei tool не овсстановить nvram
Dr_Wolodya
16.04.2016, 22:36
Oysters Arctic 450, CPU: Spreadtrum SC7715, Flash: NAND, block 256k.
"]Operation : Check/Read Info [ v1.16 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FLASH : NAND Flash , Structure : Ok!
Reading extended info ...
Model Name : Arctic450
Model Brand : Oysters
Model Device: Arctic450
AndrVersion : 4.4.2
BaseBand CPU: ARCTIC450
CompileDate : 06.11.2015 10:05:46
Project Ver : Oysters_Arctic450_SA004_06112015
Model Ext : Arctic450
ExtraInfo : HWInfo not exists, normal phone
ExtraInfo : GSM Phone
Elapsed: 00:00:28
Reconnect Power/Cable!
"]Operation : Read NV [ v1.16 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected NAND Flash , Structure detect Ok!
Read NVM Part #1
Part Ok
Read NVM Part #2
Part Ok
Saved to : D:\Mobile\Iia? iiaae?\Oysters\Arctic 450\cm2\nv\CX_SPDNV.spdnv
Elapsed: 00:00:38
Reconnect Power/Cable!
"]Operation : Read FullFlash [ v1.16 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
FlashMode Set : Ok!
Detected NAND Flash , Structure detect Ok!
[FW_READER] : Step #1 Passed!
[FW_READER] : Step #2 Passed!
[FW_READER] : Initialize Ok , 0x13 , NAND : b256k
[FW_READER] : Step #3 Passed!
Model Name : Arctic450
Model Brand : Oysters
Model Device: Arctic450
AndrVersion : 4.4.2
BaseBand CPU: ARCTIC450
Project Ver : Oysters_Arctic450_SA004_06112015
Model Ext : Arctic450
[Read Mode] : HSUSB : 0x3000
[FW_READER] : Reading Firmware Now ...
[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv_b256k.img
[Read Ok] : nvitem_w.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : sc7715_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : CP2._CP2_WCN_14C_W15.23.1_Release.bin
[Read Ok] : logo_320x480.bin
[Read Ok] : boot.img
[Read Ok] : system_b256k.img
[Read Ok] : cache_b256k.img
[Read Ok] : recovery.img
[Read Ok] : userdata_b256k.img
AndroidInfo created
Firmware Size : 287 MiB
Saved to : D:\Mobile\Oysters\Arctic 450\cm2\ARCTIC450_[NAND_b256k]_Arctic450_4.4.2_Oysters_Arctic450_SA004_06112015_ Arctic450\
Done!
Elapsed: 00:06:31
Reconnect Power/Cable!
"]Operation : SP Unlock [ v1.16 ]
Mode : DirectUnlock
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 17 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7715 Loader NAND v1.1 Infinity
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Detected NAND Flash , Structure detect Ok!
Checking Structure ...
SimLock state : Locked!
Unlocking ...
Unlock Done!
Elapsed: 00:00:14
Reconnect Power/Cable!
Успешно разблокирован, после сброса блокировка не возвращается.
новый способ для разблокировать Samsung E1272
Висел на заставле ZTE, Wipe из recovery, Format File System через CM2SPD результата не дали.
Прошивка через CM2SPD > Flash и аппарат живой, IMEI на месте.
Скрытый текст требуется (10 сообщение(ий), сейчас у вас 10):
ссылка на PAC которым восстановил данный ТА
PAC в ссылке не распаковывается - битый архив.
MobilaGSM
30.09.2016, 09:17
PAC в ссылке не распаковывается - битый архив.
Не хочется оффтопить, но обновляйте иногда программы которыми вы пользуетесь, в том числе и архиваторы.
Fly FS452. CPU: Spreadtrum SC7731, eMMC
========================= Start =========================
09.02.2017 / 13:09:41
================================================== =======
Card found: S/N : xxxxxxxx , v0134
Chinese Miracle II [SPD module] v 1.24
Loading : FS452_SW_20160810_SW18_FLY.pac
CRVersion : BP_R1.0.0
PacCPUinfo : SC77xx
PacVersion : SW18_FLY_FS452_2016_08_10
FastCheck : 0x00466B6267
Loading files ...
File : fdl1.bin
File : fdl2.bin
File : nvitem__GSMQ_band18_TS21_4506F_20160121_W15.09.bin
File : nvitem_wcn.bin
File : prodnv.img
File : u-boot-spl-16k.bin
File : SC7702_sc7731g_band128.bin
File : DSP_DM_G2.bin
File : SC8800G_x30g_wcn_dts_modem.bin
File : boot.img
File : recovery.img
File : system.img
File : userdata.img
File : fly_logo.bmp
File : fly_logo.bmp(1)
File : cache.img
File : u-boot.bin
File : SC77xx.xml
Load Ok!
Start at : [09.02.2017 / 13:10:30]
Operation : Read PatternLock [ v1.24 ]
1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable
==== Wait for phone...
Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
PickUp loaders from pac
FDL Ready!
Boot Ver : Spreadtrum Boot Block version 1.1
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!
FlashMode Set : Ok!
Reading PatternLock ...
Read Ok , decrypt
PatternLock Sequence : 658932147
Done!
Elapsed: 00:00:40
Reconnect Power/Cable!
Finish at : [09.02.2017 / 13:11:11]
MobilaGSM
11.05.2017, 21:25
Полный FULL S-Tell S3-01 под CM2SPD (от Bizon (http://www.mcrf.ru/forum/member.php?u=11012))
.:: Скрытый текст (вы должны войти под своим логином или зарегистрироваться и иметь 44 сообщение(ий)) ::.
У меня одного так или специально убрали на вкладке Security пункты IMEI?
UK Status Off.
Nikolaus
07.09.2017, 20:12
У меня одного так или специально убрали на вкладке Security пункты IMEI?
UK Status Off.
После какой версии ?
если в донгл-менеджере не помогает опция UK OFF, то удалить файл UK.txt в папке СМ2SPD.
если в донгл-менеджере не помогает опция UK OFF, то удалить файл UK.txt в папке СМ2SPD.
Все, удалил этот файлик и появились пункты IMEI.
vBulletin® v3.8.7, Copyright ©2000-2024, Jelsoft Enterprises Ltd. Перевод: zCarot