Просмотр полной версии : CM2 MTK Тест и логи удачных операций
В этой теме собираем логи удачных и не удачных операций CM2 MTK.
Lenovo A3300-H MT6582
Operation : Check / Read Info [ v1.37 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 55 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3758564D42011390E00971BF
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMVX7
[eMMC] : FLASH_CID : 1501004B3758564D42011390E00971BF
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : Lenovo
ProdName : A3300-HV
ProdModel : LenovoA3300-HV
Device : A3300-HV
AndroidVer: 4.4.2
MTKxCPU : MT6582
MTKxPRJ : A3300HV_A442_01_17_140717_ROW
MODEM :
BaseBand : MT6582_S00_A3300HV_V34_1_wg_n
Done!
Elapsed: 00:00:10
Reconnect Power/Cable!
Operation : Check / Read Info [ v1.37 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 55 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3758564D42011390E00971BF
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMVX7
[eMMC] : FLASH_CID : 1501004B3758564D42011390E00971BF
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : Lenovo
ProdName : A3300-HV
ProdModel : LenovoA3300-HV
Device : A3300-HV
AndroidVer: 4.4.2
MTKxCPU : MT6582
MTKxPRJ : A3300HV_A442_01_17_140717_ROW
MODEM :
BaseBand : MT6582_S00_A3300HV_V34_1_wg_n
Done!
Elapsed: 00:00:10
Reconnect Power/Cable!
Operation : Check / Read Info [ v1.37 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 55 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3758564D42011390E00971BF
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMVX7
[eMMC] : FLASH_CID : 1501004B3758564D42011390E00971BF
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : Lenovo
ProdName : A3300-HV
ProdModel : LenovoA3300-HV
Device : A3300-HV
AndroidVer: 4.4.2
MTKxCPU : MT6582
MTKxPRJ : A3300HV_A442_01_17_140717_ROW
MODEM :
BaseBand : MT6582_S00_A3300HV_V34_1_wg_n
Done!
Elapsed: 00:00:10
Reconnect Power/Cable!
Operation : Check / Read Info [ v1.37 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 55 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v7.1533.03
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3758564D42011390E00971BF
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMVX7
[eMMC] : FLASH_CID : 1501004B3758564D42011390E00971BF
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : Lenovo
ProdName : A3300-HV
ProdModel : LenovoA3300-HV
Device : A3300-HV
AndroidVer: 4.4.2
MTKxCPU : MT6582
MTKxPRJ : A3300HV_A442_01_17_140717_ROW
MODEM :
BaseBand : MT6582_S00_A3300HV_V34_1_wg_n
Done!
Elapsed: 00:00:10
Reconnect Power/Cable!
SergDeParchi
22.12.2015, 04:31
Lenovo A369i
попытка достаь фото (ошибка, фото в аппарате есть):
Start at : [22.12.2015 / 4:54:32]
Operation : Read UserData [ v1.39 ]
Gallery : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004E355530304D02860376239001
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , M00U5
[eMMC] : FLASH_CID : 1501004E355530304D02860376239001
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Processiung : User Photo/Video/Records extraction
Read failed, error code : 0x05
Operation Failed
Elapsed: 00:00:12
Reconnect Power/Cable!
чтение телефонной книги (успешно):
Start at : [22.12.2015 / 4:55:02]
Operation : Read UserData [ v1.39 ]
PhoneBook : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004E355530304D02860376239001
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , M00U5
[eMMC] : FLASH_CID : 1501004E355530304D02860376239001
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Processiung : PhoneBook extraction
Step #1
Step #2
Read Ok, PhoneBook records extracted : 170
TXT Saved to : C:\InfinityBox\CM2MTK\PhData\MT6572_PhoneBook.txt
Write : 170
CSV Saved to : C:\InfinityBox\CM2MTK\PhData\MT6572_PhoneBook.csv
Write : 170
VCF Saved to : C:\InfinityBox\CM2MTK\PhData\MT6572_PhoneBook.vcf
Write : 170
Done!
Elapsed: 00:00:22
Reconnect Power/Cable!
Finish at : [22.12.2015 / 4:55:25]
Read Flash (успешно):
Start at : [22.12.2015 / 5:03:16]
Operation : Read Flash [ v1.39 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004E355530304D02860376239001
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , M00U5
[eMMC] : FLASH_CID : 1501004E355530304D02860376239001
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Conent now ...
Read Ok , collect info
Brand : Lenovo
ProdName : A369i
ProdModel : Lenovo A369i
Device : A369i
AndroidVer: 4.2.2
MTKxCPU : MT6572
MTKxPRJ : ALPS.JB3.MP.V1
Saved to : C:\InfinityBox\CM2MTK\Flash\MT6572__LENOVO__Lenovo _A369i__ALPS.JB3.MP.V1__Android_4.2.2__20140610_09 4715.ispff
Done!
Elapsed: 00:19:33
Reconnect Power/Cable!
Finish at : [22.12.2015 / 5:22:49]
Lenovo A536:
попытка извлечь фото (выскакивает ошибка):
Start at : [22.12.2015 / 6:21:26]
Operation : Read UserData [ v1.39 ]
Gallery : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3758564D42017E9EB4ED912F
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMVX7
[eMMC] : FLASH_CID : 1501004B3758564D42017E9EB4ED912F
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Processiung : User Photo/Video/Records extraction
остальные операции успешно
A369i - Фотки, скорее всего, в FAT'e, добавлю, как закончу DD для FAT'a.
A536 - глянул бы дамп с удовольствием. Интересный экземпляр.
Паш вопросик, есть Alcatel OT-4032, с ними никак по разлоку?
SergDeParchi
22.12.2015, 23:58
A536 - дамп (https://yadi.sk/d/g2p5J8UDmR4aC).
Паш вопросик, есть Alcatel OT-4032, с ними никак по разлоку?
А что с ними не так? Не припомню такой.
P.S. в 1.40 сделал тесты памяти и проверку на ReadOnly. Вроде у тестировавших людей работает, как надо. Тесты памяти НЕ повреждают прошивку, данные пользователя и что-либо еще.
Dr_Wolodya
25.12.2015, 18:44
Успешно удалён FRP Lock с Lenovo A2010-a:Operation : Format FileSystem [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 22 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6735
BB_CPU_HW : CA00
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6735_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 460001154D32323789C30042293AEBE4
DA Stat : v4.2 on BBID : 0x93
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BM227
[eMMC] : FLASH_CID : 150100463732324D4200C389E4EB7229
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Clear FRP ( Google Reset Protection )
Clear Ok!
Done!
Elapsed: 00:00:16
Reconnect Power/Cable!
SergDeParchi
26.12.2015, 20:31
Alcatel OT-7047D Clear UserLocks (стоял PIN) успешно:
Operation : Clear UserLocks [Pin/Pwd/Pattern/FVLock/GoogleAcc] [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004B3558564D4201BEC6FEC14217
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMVX5
[eMMC] : FLASH_CID : 1501004B3558564D4201BEC6FEC14217
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
LSSA Ok!
LSSW Ok!
LSSS Ok!
LSSK Ok!
LSSG Ok!
Security Settings : Clear Ok!
[Info] : Android 5.x / MT67xx : If phone stuck on "Logo"
1. Wait 2-3 minutes. Power Off phone by long press "Power" button
2. Power On phone again
3. Or wait up to 3-7 minutes, until phone start by itself
4. Also recommended reboot phone twice before start use it
Done!
Elapsed: 00:00:23
Reconnect Power/Cable!
Lenovo S920 чтение телефонной книги (успешно) и фото (не удалось):
Operation : Read UserData [ v1.40 ]
PhoneBook : Enabled
PhoneBook : VCFv3 Format output Enabled
Gallery : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4B0001153030534A1302034DAD60596F
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , M00SJ
[eMMC] : FLASH_CID : 1501004B4A5330304D0302136F5960AD
[eMMC] : FLASH_EXT : 0x00100000 , 0x00100000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Processiung : PhoneBook extraction
Step #1
Step #2
Read Ok, PhoneBook records extracted : 845
TXT Saved to : C:\InfinityBox\CM2MTK\PhData\MT6583_PhoneBook.txt
Write : 845
CSV Saved to : C:\InfinityBox\CM2MTK\PhData\MT6583_PhoneBook.csv
Write : 845
VCF Saved to : C:\InfinityBox\CM2MTK\PhData\MT6583_PhoneBook.vcf
Write : 845
VCFv3 Saved to : C:\InfinityBox\CM2MTK\PhData\MT6583_PhoneBook_v3.v cf
Processiung : User Photo/Video/Records extraction
после чего выскакивает ошибка как на скриншоте выше.
SergDeParchi
26.12.2015, 20:55
Micromax X337 чтение данных (не удачно):
Operation : Read UserData [ v1.40 ]
PhoneBook : Enabled
Gallery : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )
Wait for phone...
Phone found! [ 23 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : 8C8F7339D18592FC3899D4B1D9C6D06F
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : EF00 6000 1800 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F8 , [WINBOND] W25Q128FW
[0] : FLASH_DIE : 00EF 0060 0018 0000
[0] : FLASH_LEN : 0x01000000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000
SDS_INFO : Not exists
Processiung : PhoneBook extraction
Step #1
Step #2
Error! Seems as unknown type! Send DUMP + Report to support!
Operation Failed
Elapsed: 00:00:12
Reconnect Power/Cable!
Doogee X5 чтение данных (не удачно):
Operation : Read UserData [ v1.40 ]
PhoneBook : Enabled
Gallery : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6580
BB_CPU_HW : CA00
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6580_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 90014A48384731650507E257281F625D
DA Stat : v4.2 on BBID : 0x94
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A48384731650507E257281F625D
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Processiung : PhoneBook extraction
Step #1
Error while reading PhoneBook! Code : 0x01 :(
Operation Failed
Elapsed: 00:00:19
Reconnect Power/Cable!
А что с ними не так? Не припомню такой.
P.S. в 1.40 сделал тесты памяти и проверку на ReadOnly. Вроде у тестировавших людей работает, как надо. Тесты памяти НЕ повреждают прошивку, данные пользователя и что-либо еще.
Паш пишет разлок ок, но его нет, ну может пробллема в том что счетсчик увален
1.40 завтра скажу, писал с 1.39
Добавлено через 2 минуты
Micromax X337 чтение данных (не удачно):
Operation : Read UserData [ v1.40 ]
PhoneBook : Enabled
Gallery : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )
Wait for phone...
Phone found! [ 23 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : 8C8F7339D18592FC3899D4B1D9C6D06F
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : EF00 6000 1800 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00F8 , [WINBOND] W25Q128FW
[0] : FLASH_DIE : 00EF 0060 0018 0000
[0] : FLASH_LEN : 0x01000000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000
SDS_INFO : Not exists
Processiung : PhoneBook extraction
Step #1
Step #2
Error! Seems as unknown type! Send DUMP + Report to support!
Operation Failed
Elapsed: 00:00:12
Reconnect Power/Cable!
Doogee X5 чтение данных (не удачно):
Operation : Read UserData [ v1.40 ]
PhoneBook : Enabled
Gallery : Enabled
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 20 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6580
BB_CPU_HW : CA00
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6580_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 90014A48384731650507E257281F625D
DA Stat : v4.2 on BBID : 0x94
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e1G8
[eMMC] : FLASH_CID : 90014A48384731650507E257281F625D
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Processiung : PhoneBook extraction
Step #1
Error while reading PhoneBook! Code : 0x01 :(
Operation Failed
Elapsed: 00:00:19
Reconnect Power/Cable!
ну здесь вероято флеша не попадалась
Micromax bolt D303 unlock megafon
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 11010030303447453001609C6CF792DF
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0011 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 0EG40
[eMMC] : FLASH_CID : 11010030303447453001609C6CF792DF
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Lock Status : Locked!
Unlocking ...
Unlock done!
CCCMATRIX
28.12.2015, 19:54
Micromax bolt D303 unlock megafon
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 11010030303447453001609C6CF792DF
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0011 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 0EG40
[eMMC] : FLASH_CID : 11010030303447453001609C6CF792DF
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Lock Status : Locked!
Unlocking ...
Unlock done!
У меня разлочился только 1 слот а 2ой просил код сети..и если сбросить настройки на заводские первый слот повторно лочится.
У меня разлочился только 1 слот а 2ой просил код сети..и если сбросить настройки на заводские первый слот повторно лочится.
так и есть, сразу не обратил внимание, щас перешиваю их. Просто уэе продали 1 из 3х надо быстро сделать, шью с форматом потом правка и в бой
По Alcatel
Card fo
Chinese Miracle II [MTK module] v 1.40
Operation : SP Unlock [ v1.40 ]
Mode : Direct Unlock
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 10 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : FE014E50314A3934481261ECA13CC1B1
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 00FE , OEM : 014E
[eMMC] : FLASH_INF : [MICRON] , H49J1
[eMMC] : FLASH_CID : FE014E50314A3934481261ECA13CC1B1
[eMMC] : FLASH_EXT : 0x00100000 , 0x00100000 , 0x00100000
[eMMC] : FLASH_LEN : 0x00000000E9800000
[eMMC] : FLASH_UCP : 3736 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Lock Status : Locked!
Unlocking ...
Unlock done!
Done!
Elapsed: 00:00:30
Reconnect Power/Cable!
CCCMATRIX
29.12.2015, 14:02
так и есть, сразу не обратил внимание, щас перешиваю их. Просто уэе продали 1 из 3х надо быстро сделать, шью с форматом потом правка и в бой
Также сделал штук 200 было .. пришлось все перешивать и править имей.. К стати Sigma box тоже самое.. разлачивает первый и второй слот.. но после сброса повторно блокируются :)
Fly iq434 flashtool вечно выдавал ошибки, сделал full factory CM2 и тело заработало
-------------dumping platform config-------------
name:MT6571_S00
simple_name:MT6571
-----------------------------------------------
(..\QT_FlashTool_Refactor\Setting\PlatformSetting. cpp,106)
01/12/2016 12:37:10.278 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6516).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.278 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.278 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.278 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.278 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.278 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6573).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.279 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(false), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.279 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.279 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.279 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.279 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6575).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.279 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.280 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.280 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.280 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(true), is_support_auto_format(false), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.280 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6577).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.280 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.281 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.281 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.281 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(true), is_support_auto_format(false), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.281 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6589).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.281 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.281 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.281 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.282 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(true), is_support_auto_format(false), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.282 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6572).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.282 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.282 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.282 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.282 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.283 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6571).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.283 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.283 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.283 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.283 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.284 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6582).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.284 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.284 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.284 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.284 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.284 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT6592).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.285 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.285 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.285 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.285 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.285 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): platform(MT8135).(..\QT_FlashTool_Refactor\Rules\S torageRule.cpp,140)
01/12/2016 12:37:10.285 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(EMMC) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_EMMC), memory_type_(HW_MEM_EMMC).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.286 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NAND) -> is_support(true), is_support_auto_format(true), storage_type_(HW_STORAGE_NAND), memory_type_(HW_MEM_NAND).(..\QT_FlashTool_Refacto r\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.286 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(NOR) -> is_support(false), is_support_auto_format(false), storage_type_(HW_STORAGE_NOR), memory_type_(HW_MEM_NOR).(..\QT_FlashTool_Refactor \Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.286 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): storage type(SDMMC) -> is_support(true), is_support_auto_format(false), storage_type_(HW_STORAGE_SDMMC), memory_type_(HW_MEM_SDMMC).(..\QT_FlashTool_Refact or\Rules\StorageRule.cpp,144)
01/12/2016 12:37:10.286 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): Storage type(HW_STORAGE_NOR) -> Storage name(NOR).(..\QT_FlashTool_Refactor\Rules\StorageR ule.cpp,154)
01/12/2016 12:37:10.286 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): Storage type(HW_STORAGE_NAND) -> Storage name(NAND).(..\QT_FlashTool_Refactor\Rules\Storage Rule.cpp,154)
01/12/2016 12:37:10.286 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): Storage type(HW_STORAGE_EMMC) -> Storage name(EMMC).(..\QT_FlashTool_Refactor\Rules\Storage Rule.cpp,154)
01/12/2016 12:37:10.287 FlashTool[4512][1128][D]: FlashToolStorageTable::Dump(): Storage type(HW_STORAGE_SDMMC) -> Storage name(SDMMC).(..\QT_FlashTool_Refactor\Rules\Storag eRule.cpp,154)
01/12/2016 12:37:10.287 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): platform(MT6571), storage_name(NAND) to be queried.(..\QT_FlashTool_Refactor\Rules\StorageRul e.cpp,164)
01/12/2016 12:37:10.287 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): platform(MT6516) in the table.(..\QT_FlashTool_Refactor\Rules\StorageRule. cpp,171)
01/12/2016 12:37:10.287 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): platform(MT6573) in the table.(..\QT_FlashTool_Refactor\Rules\StorageRule. cpp,171)
01/12/2016 12:37:10.287 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): platform(MT6575) in the table.(..\QT_FlashTool_Refactor\Rules\StorageRule. cpp,171)
01/12/2016 12:37:10.288 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): platform(MT6577) in the table.(..\QT_FlashTool_Refactor\Rules\StorageRule. cpp,171)
01/12/2016 12:37:10.288 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): platform(MT6589) in the table.(..\QT_FlashTool_Refactor\Rules\StorageRule. cpp,171)
01/12/2016 12:37:10.288 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): platform(MT6572) in the table.(..\QT_FlashTool_Refactor\Rules\StorageRule. cpp,171)
01/12/2016 12:37:10.288 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): platform(MT6571) in the table.(..\QT_FlashTool_Refactor\Rules\StorageRule. cpp,171)
01/12/2016 12:37:10.288 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): MT6571 is matched.(..\QT_FlashTool_Refactor\Rules\StorageRul e.cpp,174)
01/12/2016 12:37:10.288 FlashTool[4512][1128][D]: FlashToolStorageTable::QueryStorageInfo(): NAND type is matched, and (Yes) be supported.(..\QT_FlashTool_Refactor\Rules\StorageR ule.cpp,181)
01/12/2016 12:37:10.288 FlashTool[4512][1128][D]: FlashToolStorageConfig::QueryStorage(): (MT6571) is supported by (NAND).(..\QT_FlashTool_Refactor\Rules\StorageRule .cpp,287)
01/12/2016 12:37:10.289 FlashTool[4512][1128][D]: FlashToolStorageConfig::IsOperationChangend(): Old platform(), storage type().(..\QT_FlashTool_Refactor\Rules\StorageRule .cpp,342)
01/12/2016 12:37:10.289 FlashTool[4512][1128][D]: FlashToolStorageConfig::IsOperationChangend(): New platform(MT6571), storage type(NAND).(..\QT_FlashTool_Refactor\Rules\Storage Rule.cpp,348)
01/12/2016 12:37:10.289 FlashTool[4512][1128][D]: APCore::PlatformSetting::getLoadPlatformName(): PlatformSetting::getLoadPlatformName(): MT6571(..\QT_FlashTool_Refactor\Setting\PlatformSe tting.cpp,166)
01/12/2016 12:37:10.312 FlashTool[4512][1128][D]: APCore::DLHandle::GetScatterInfo(): Scatter version(V1.1.1)(..\QT_FlashTool_Refactor\Resource\ Handle\DLHandle.cpp,92)
01/12/2016 12:37:10.316 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(0): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:37:10.317 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(5): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:37:10.317 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(6): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:37:10.318 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(7): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:37:10.319 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(8): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:37:10.320 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(10): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:37:10.320 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(12): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:37:10.321 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(14): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:37:10.321 FlashTool[4512][1128][D]: AppCore::EnableDAChksum(): Enable DA Chksum.(..\QT_FlashTool_Refactor\Public\AppCore.cp p,411)
01/12/2016 12:37:10.322 FlashTool[4512][1128][D]: APCore::DLHandle::EnableDAChksum(): set DL_SetChecksumEnable(True).(..\QT_FlashTool_Refact or\Resource\Handle\DLHandle.cpp,160)
01/12/2016 12:37:11.751 FlashTool[4512][1128][D]: ISetting::set_stop_flag(): dummpy stop_flag(0x03D4F240) set.(e:\qt flashtool\qt_flashtool_refactor\setting\ISetting.h ,37)
01/12/2016 12:37:11.751 FlashTool[4512][848][D]: APCore::Connection::ConnectBROM(): Connecting to BROM...(..\QT_FlashTool_Refactor\Conn\Connection.c pp,90)
01/12/2016 12:37:11.751 FlashTool[4512][848][D]: APCore::ConnMediaUSB::PreConnect(): Scanning USB port...(..\QT_FlashTool_Refactor\Conn\ConnMedia.cp p,36)
01/12/2016 12:37:37.091 FlashTool[4512][848][D]: USBSetting::SearchUSBPortPool(): USB port is obtained. path name(\\?\usb#vid_0e8d&pid_0003#5&13735d69&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}), port name(MTK USB Port (COM37))(..\QT_FlashTool_Refactor\Conn\USBSetting. cpp,158)
01/12/2016 12:37:37.091 FlashTool[4512][848][D]: APCore::ConnMediaUSB::PreConnect(): USB port detected: \\?\usb#vid_0e8d&pid_0003#5&13735d69&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}(..\QT_FlashTool_Refactor\Conn\ConnMe dia.cpp,42)
01/12/2016 12:37:37.210 FlashTool[4512][848][D]: APCore::Connection::ConnectBROM(): BROM connected(..\QT_FlashTool_Refactor\Conn\Connection .cpp,100)
01/12/2016 12:37:37.210 FlashTool[4512][848][D]: APCore::Connection::ConnectDA(): Downloading & Connecting to DA...(..\QT_FlashTool_Refactor\Conn\Connection.cpp ,131)
01/12/2016 12:37:37.211 FlashTool[4512][848][D]: BromBootArg::cb_com_init_stage(): COM port is open. Trying to sync with the target...(..\QT_FlashTool_Refactor\Arg\BootRomArg. cpp,184)
01/12/2016 12:37:37.211 FlashTool[4512][848][D]: BromBootArg::cb_com_init_stage(): hCOM(00000A6C).(..\QT_FlashTool_Refactor\Arg\BootR omArg.cpp,186)
01/12/2016 12:37:38.038 FlashTool[4512][1128][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.c pp,478)
01/12/2016 12:38:00.617 FlashTool[4512][848][D]: APCore::Connection::ConnectDA(): Failed to Connect DA: S_FT_DA_NO_RESPONSE(..\QT_FlashTool_Refactor\Conn\ Connection.cpp,145)
01/12/2016 12:38:16.837 FlashTool[4512][848][D]: BackgroundWorker::run(): BROM Exception! ( BROM ERROR : S_FT_DA_NO_RESPONSE (4001)
DA didn't send response data to FlashTool!
[HINT]:
)((APCore::Connection::ConnectDA,..\QT_FlashTool_R efactor\Conn\Connection.cpp,146))(..\QT_FlashTool_ Refactor\UI\src\BackgroundWorker.cpp,94)
01/12/2016 12:38:17.811 FlashTool[4512][1128][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDia log.cpp,483)
01/12/2016 12:38:34.162 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(0): 0(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.165 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(5): 0(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.168 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(6): 0(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.171 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(7): 0(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.174 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(8): 0(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.177 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(10): 0(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.180 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(12): 0(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.183 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(14): 0(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.186 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(0): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.187 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(5): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.189 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(6): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.191 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(7): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.192 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(8): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.194 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(10): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.196 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(12): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.197 FlashTool[4512][1128][D]: AppCore::EnableROM(): enable ROM(14): 1(..\QT_FlashTool_Refactor\Public\AppCore.cpp,325)
01/12/2016 12:38:34.898 FlashTool[4512][1128][D]: ISetting::set_stop_flag(): dummpy stop_flag(0x03D4F240) set.(e:\qt flashtool\qt_flashtool_refactor\setting\ISetting.h ,37)
01/12/2016 12:38:34.898 FlashTool[4512][5436][D]: APCore::Connection::ConnectBROM(): Connecting to BROM...(..\QT_FlashTool_Refactor\Conn\Connection.c pp,90)
01/12/2016 12:38:34.899 FlashTool[4512][5436][D]: APCore::ConnMediaUSB::PreConnect(): Scanning USB port...(..\QT_FlashTool_Refactor\Conn\ConnMedia.cp p,36)
01/12/2016 12:38:38.885 FlashTool[4512][5436][D]: USBSetting::SearchUSBPortPool(): USB port is obtained. path name(\\?\usb#vid_0e8d&pid_0003#5&13735d69&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}), port name(MTK USB Port (COM37))(..\QT_FlashTool_Refactor\Conn\USBSetting. cpp,158)
01/12/2016 12:38:38.886 FlashTool[4512][5436][D]: APCore::ConnMediaUSB::PreConnect(): USB port detected: \\?\usb#vid_0e8d&pid_0003#5&13735d69&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}(..\QT_FlashTool_Refactor\Conn\ConnMe dia.cpp,42)
01/12/2016 12:38:38.994 FlashTool[4512][5436][D]: APCore::Connection::ConnectBROM(): BROM connected(..\QT_FlashTool_Refactor\Conn\Connection .cpp,100)
01/12/2016 12:38:38.994 FlashTool[4512][5436][D]: APCore::Connection::ConnectDA(): Downloading & Connecting to DA...(..\QT_FlashTool_Refactor\Conn\Connection.cpp ,131)
01/12/2016 12:38:38.996 FlashTool[4512][5436][D]: BromBootArg::cb_com_init_stage(): COM port is open. Trying to sync with the target...(..\QT_FlashTool_Refactor\Arg\BootRomArg. cpp,184)
01/12/2016 12:38:38.996 FlashTool[4512][5436][D]: BromBootArg::cb_com_init_stage(): hCOM(000007EC).(..\QT_FlashTool_Refactor\Arg\BootR omArg.cpp,186)
01/12/2016 12:38:39.874 FlashTool[4512][1128][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.c pp,478)
01/12/2016 12:39:02.274 FlashTool[4512][5436][D]: APCore::Connection::ConnectDA(): Failed to Connect DA: S_FT_DA_NO_RESPONSE(..\QT_FlashTool_Refactor\Conn\ Connection.cpp,145)
01/12/2016 12:39:11.810 FlashTool[4512][1128][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDia log.cpp,483)
01/12/2016 12:39:12.284 FlashTool[4512][5436][D]: BackgroundWorker::run(): BROM Exception! ( BROM ERROR : S_FT_DA_NO_RESPONSE (4001)
DA didn't send response data to FlashTool!
[HINT]:
)((APCore::Connection::ConnectDA,..\QT_FlashTool_R efactor\Conn\Connection.cpp,146))(..\QT_FlashTool_ Refactor\UI\src\BackgroundWorker.cpp,94)
01/12/2016 12:41:09.111 FlashTool[4512][1128][D]: OptionDialog::winEvent(): USB Device plug in.(..\QT_FlashTool_Refactor\UI\src\OptionDialog.c pp,478)
01/12/2016 12:41:18.810 FlashTool[4512][1128][D]: OptionDialog::winEvent(): USB Device Removed.(..\QT_FlashTool_Refactor\UI\src\OptionDia log.cpp,483)
01/12/2016 12:41:49.905 FlashTool[4512][1128][D]: MainWindow::closeEvent(): UI has unlocked!(..\QT_FlashTool_Refactor\UI\src\MainWind ow.cpp,1400)
01/12/2016 12:41:49.959 FlashTool[4512][1128][D]: BackgroundWorker::~BackgroundWorker(): dtor of BackgroundWorker...(..\QT_FlashTool_Refactor\UI\sr c\BackgroundWorker.cpp,22)
01/12/2016 12:41:49.961 FlashTool[4512][1128][D]: APCore::DAHandle::~DAHandle(): dtor of DAHandle(..\QT_FlashTool_Refactor\Resource\Handle\ DAHandle.cpp,25)
01/12/2016 12:41:49.962 FlashTool[4512][1128][D]: APCore::DLHandle::~DLHandle(): dtor of DLHandle(..\QT_FlashTool_Refactor\Resource\Handle\ DLHandle.cpp,23)
01/12/2016 12:41:49.962 FlashTool[4512][1128][D]: APCore::RBHandle::~RBHandle(): dtor of RBHandle(..\QT_FlashTool_Refactor\Resource\Handle\ RBHandle.cpp,19)
01/12/2016 12:41:49.963 FlashTool[4512][1128][D]: APCore::RBHandle::~RBHandle(): RB_ClearAll(0)(..\QT_FlashTool_Refactor\Resource\H andle\RBHandle.cpp,21)
01/12/2016 12:41:49.963 FlashTool[4512][1128][D]: APCore::RBHandle::~RBHandle(): RB_Destroy(0)(..\QT_FlashTool_Refactor\Resource\Ha ndle\RBHandle.cpp,23)
01/12/2016 12:41:49.963 FlashTool[4512][1128][D]: APCore::ScretHandle::~ScretHandle(): dtor of ScretHandle(..\QT_FlashTool_Refactor\Resource\Hand le\ScretHandle.cpp,22)
01/12/2016 12:41:49.963 FlashTool[4512][1128][D]: APCore::AuthHandle::~AuthHandle(): dtor of auth handle.(..\QT_FlashTool_Refactor\Resource\Handle\A uthHandle.cpp,21)
Logger deinited.
Wait for phone...
Phone found! [ 37 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6571
BB_CPU_HW : CA00
BB_CPU_SW : 8D00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6571_S00
Processing BROM stage
BLVersion : 0xFE
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 002C00BC009000660054000000000000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x8B
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00A8
DRAM Init Ok , 0x10000000
DA Sent. Configure setting now ...
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0088 , [Micron] NAND_MT29C4G48MAAHBAAKS_5WT
[NAND] : FLASH_DIE : 002C 00BC 0090 0066 0054 0000 0000
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
INT RAM : 0x00020000
EXT RAM : 0x10000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!
Done!
Elapsed: 00:00:15
Reconnect Power/Cable!
lenovo a316 полностью рабочий, пробовал 2 разных, наверно нет в базе типа флеш.
Wait for phone...
Phone found! [ 18 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00AD00BC00900055005600AD00BC0000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x009A , [Hynix] H9TA4GH2GDMCPR
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0056 00AD 00BC
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/01/NIM_Px-2
INT RAM : 0x00020000
EXT RAM : 0x10000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Info read not done :( Erased phone or unsupported FlashIc?
You can change settings : Settings -> Other -> NAND init Mode
Done!
Elapsed: 00:00:12
Reconnect Power/Cable!
MobilaGSM
13.01.2016, 10:15
lenovo a316 полностью рабочий, пробовал 2 разных, наверно нет в базе типа флеш.
Wait for phone...
Phone found! [ 18 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00AD00BC00900055005600AD00BC0000
eMMC_ID : 00000000000000000000000000000000
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x009A , [Hynix] H9TA4GH2GDMCPR
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0056 00AD 00BC
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/01/NIM_Px-2
INT RAM : 0x00020000
EXT RAM : 0x10000000
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Info read not done :( Erased phone or unsupported FlashIc?
You can change settings : Settings -> Other -> NAND init Mode
Done!
Elapsed: 00:00:12
Reconnect Power/Cable!
C Lenovo A316i таких проблем нет.
Сори что тут спрашиваю (не хочу создавать новую тему )
JayDi писал что в новой 1.40 версии добавил тест памяти на рид-онли не затрагивая прошивки , через какую кнопку это делать ?
[Processing] FlashMemory Read-Write test
[eMMC] : [SAMSUNG] , BMZX5 , 0xE9000000 , 3728 MiB
[eMMC] : CID : 1501004E35585A4D4201DCDE5B76C0FB
[eMMC] : MODE : SQ-WR
[FAILED : READONLY] : eMMC state seems as READ-ONLY !!!!
Только замена ?
0xMihalich
14.01.2016, 01:56
[Processing] FlashMemory Read-Write test
[eMMC] : [SAMSUNG] , BMZX5 , 0xE9000000 , 3728 MiB
[eMMC] : CID : 1501004E35585A4D4201DCDE5B76C0FB
[eMMC] : MODE : SQ-WR
[FAILED : READONLY] : eMMC state seems as READ-ONLY !!!!
Только замена ?
у Вас emmc samsung можете попробовать через easy jtag обновить на ней ПО затем назад пролить дампы. возможно проблема решится
Иван Ашуров
31.01.2016, 13:07
LEXAND SC7 PRO HD не удалил вирус, хотя показал что удалил!
Operation : Remove Viruses [SmartAV] [ v1.40 ]
SmartAV Conf : 100/80/2000
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 3 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 8801034E43617264203499978A63512D
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0088 , OEM : 0103
[eMMC] : FLASH_INF : [FORESEE] , draC
[eMMC] : FLASH_CID : 8801034E43617264203499978A63512D
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00000000
[eMMC] : FLASH_LEN : 0x00000001CE100000
[eMMC] : FLASH_UCP : 7393 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
SmartAV Init Ok!
Scanning FileSystem now , please wait
Scan Done, infected files found : 21
Removing infected files and scripts ...
SmartAV Report : Removed 21 infected files!
Making additional operations ...
Special Op #1 : Clear Recovery Data Ok!
Special Op #2 : Clear UserData Ok!
Special Op #3 : PostFix Ok!
Done!
Done!
Elapsed: 00:00:42
Reconnect Power/Cable!
При повторном показывает тоже самое!
Мануал. Читать мануал. На саппорте лежит.
Там подробно все описано.
Словарь на тысячу с чутком вирусов здесь : http://www.4shared.com/file/sNdSrPy6ce/EMC3.html
Класть в CM2MTK/Boot/ с заменой старого.
Модель ZTE Leo M1
На любую операцию в InfinityBox CM2MTK ,
выдаёт такой лог : Error! SECURE BOOT target! Check Model Settings!
Wait for phone...
Phone found! [ 50 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
Error : DA init Failed! Error code : 0x2
LErr : 2001
Error! SECURE BOOT target! Check Model Settings!
Boot Error!
Operation Failed
Elapsed: 00:00:26
Reconnect Power/Cable!
Люди на 4пда тоже мучаються не могут прошить , якобы бутлоадырь хитрый не даёт шить ничего , подменяют с других моделей у кого то получилось , у меня не как . можно что то сделать ?
(кастом прошивку хочу поставить , телефон полностью работает )
MobilaGSM
02.02.2016, 22:23
Модель ZTE Leo M1
На любую операцию в InfinityBox CM2MTK ,
выдаёт такой лог : Error! SECURE BOOT target! Check Model Settings!
Prestigio PMT5887_3G, аналогичная с история с secure boot.
модель : Lenovo Vibe X2, проц MediaTek MT6595 , при прошивки потерялось имя . CM2 не справился с заданием :(
MobilaGSM
08.02.2016, 08:52
Operation : Check / Read Info [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )
Wait for phone...
Phone found! [ 3 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : 0369CF58334383EADE608958288E9378
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : C800 6000 1700 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00ED , [GigaDevice] GD25LQ64
[0] : FLASH_DIE : 00C8 0060 0017 0000
[0] : FLASH_LEN : 0x00800000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000
SDS_INFO : 0x007FE000 , 0x00002000
Done!
Elapsed: 00:00:04
Reconnect Power/Cable!
Operation : Format FileSystem [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )
Wait for phone...
Phone found! [ 3 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : 0369CF58334383EADE608958288E9378
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : C800 6000 1700 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00ED , [GigaDevice] GD25LQ64
[0] : FLASH_DIE : 00C8 0060 0017 0000
[0] : FLASH_LEN : 0x00800000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000
SDS_INFO : 0x007FE000 , 0x00002000
Backup done
Executing FFS FORMAT now...
FAT_RANGE : 0x00690000-0x007FDFFF , LEN : 0x0016E000
DA_RET : DA_IN_PROGRESS
DA_RET : FORMAT_DONE
Done!
Elapsed: 00:00:23
Reconnect Power/Cable!
Operation : Read Flash [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )
Wait for phone...
Phone found! [ 3 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : 0369CF58334383EADE608958288E9378
BROM Protocol Version : 05
Setting...
RTC/PowerLatch Settings Failed #2 (HW/Connection Error)
Boot Error!
Operation Failed
Elapsed: 00:00:04
Reconnect Power/Cable!
Operation : Read Flash [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )
Wait for phone...
Phone found! [ 3 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : 0369CF58334383EADE608958288E9378
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : C800 6000 1700 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00ED , [GigaDevice] GD25LQ64
[0] : FLASH_DIE : 00C8 0060 0017 0000
[0] : FLASH_LEN : 0x00800000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000
SDS_INFO : 0x007FE000 , 0x00002000
Reading Flash Conent now ...
Read Flash now
Read Ok , 8388608 bytes read
Check and collect compile info
File_Info : FARSIGHTED60A_BU2_11B_PCB01_gprs_MT6260_S00.MMX_X2 420_RU_SW_V004_HW_V1_2.bin
FileVersion : MMX_X2420_RU_SW_V004_HW_V1.2
Saved to : D:\InfinityBox\CM2MTK\Read_out\FARSIGHTED60A_BU2_1 1B_PCB01_gprs_MT6260_S00.MMX_X2420_RU_SW_V004_HW_V 1_2.bin
Done!
Elapsed: 00:00:23
Reconnect Power/Cable!
Operation : Read Flash [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey ( '*' )
Wait for phone...
Phone found! [ 3 ]
Sync...
Sync Ok, read regs...
Inital regs read done
Boot Info :
BB_CPU_ID : 6260
BB_CPU_HW : CB00
BB_CPU_SW : 0000
BB_CPU_SB : 8000
BB_CPU_NM : [MediaTek] MT6260_S0000
BB_CPU_SN : 0369CF58334383EADE608958288E9378
BROM Protocol Version : 05
Setting...
Setting done , result code 0x000E
BROM stage done
Seek and prepare DownloadAgent
DownloadAgent matching HW Found!
DA verify and select done
Sending DA to target ...
InitRes : 00000000
DEV[0] : C800 6000 1700 0000
DEV[1] : 0000 0000 0000 0000
DA_INFO : 0xC0 , Ver : 3.2 , BBID : 0x8B
DA_CSTAT : 0x5A
SOC_VERIFY : 0xC1
BOOT_STYLE : SF_FLASH_BOOT
NOR Flash IC initialized
[0] : FLASH_VEN : 0x00ED , [GigaDevice] GD25LQ64
[0] : FLASH_DIE : 00C8 0060 0017 0000
[0] : FLASH_LEN : 0x00800000
INT_RAM : 0x0000D000
EXT_RAM : 0x00800000
SDS_INFO : 0x007FE000 , 0x00002000
Reading Flash Conent now ...
Read Flash now
Read Ok , 8388608 bytes read
Check and collect compile info
File_Info : FARSIGHTED60A_BU2_11B_PCB01_gprs_MT6260_S00.MMX_X2 420_RU_SW_V004_HW_V1_2.bin
FileVersion : MMX_X2420_RU_SW_V004_HW_V1.2
[ScatCFG] : MT6260 / MMX_X2420_RU_SW_V004_HW_V1.2 / NOR , SF
Firmware saved to : D:\InfinityBox\CM2MTK\Read_out\FARSIGHTED60A_BU2_1 1B_PCB01_gprs_MT6260_S00\
Done!
Elapsed: 00:00:29
Reconnect Power/Cable!
Пришел с user code, format fs - кода нет, imei на месте :appl:
в аттаче FULL, FIRMWARE, COVER
ViewSonic ViewPad 7Q из этой темы (http://www.mcrf.ru/forum/showthread.php?t=38937).
[ v1.40 ]"]Operation : Remove Viruses [SmartAV] [ v1.40 ]
SmartAV Conf : 100/80/2000
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 49 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4D00011557324741A86E0141F3504EE8
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , AW2GA
[eMMC] : FLASH_CID : 1501004D4147325741016EA8E84E50F3
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
SmartAV Init Ok!
Scanning FileSystem now , please wait
Scan Done, infected files found : 76
Removing infected files and scripts ...
SmartAV Report : Removed 76 infected files!
Making additional operations ...
Special Op #1 : Clear Recovery Data Ok!
Special Op #3 : PostFix Ok!
Done!
Done!
Elapsed: 00:02:47
Reconnect Power/Cable!
Operation : Format FileSystem [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 49 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4D00011557324741A86E0141F3504EE8
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , AW2GA
[eMMC] : FLASH_CID : 1501004D4147325741016EA8E84E50F3
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!
Done!
Elapsed: 00:00:17
Reconnect Power/Cable!
Спустя некоторое время на дисплее стала появляться банерная реклама.
Удаление программ в ручную. Так как прошивка odex, удалил все applikatoin.apk не имеющие соответствующий applikatoin.odex.
[ v1.40 ]"]Operation : Scan APPs [DDirect] [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 49 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 4D00011557324741A86E0141F3504EE8
DA Stat : v3.2 on BBID : 0x86
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , AW2GA
[eMMC] : FLASH_CID : 1501004D4147325741016EA8E84E50F3
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000003A3E00000
[eMMC] : FLASH_UCP : 14910 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
DDirect : Init Ok!
Scanning FileSystem now , please wait
[User Select] : Remove Files and Garbage
[DDCleaner Info] : Files to remove : 30
[DDCleaner Info] : Additional garbage detected : 0
Removing files ...
[DDCleaner] : Removed 30
Special Op #1 : Clear Recovery Data Ok!
Special Op #3 : PostFix Ok!
All Done!
Так-как прошивку найти не удалось, бекап будет позже.
Бепап NV и дамп прошивки (http://www.mcrf.ru/forum/showthread.php?t=38937).
Не удается прошить Lenovo P780 (P780_S228_4GB_KK_ROW). При выборе MT6589_Android_scatter_emmc.txt не подгружается один из файлов (preload.img).
Scatter Load Ok , BaseBand : MT6589 , Project : MTK6589 , Storage : eMMC
Files found : 13 , Set to Flash : 12
Ready to Flash!
Получаем ошибку записи.
"]======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 10 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6583
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6583|6589_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0x05
BLVersion : 0xFE
Preloader Status : Not active (Erased)
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 204A0190594E49582EA11648076070D0
DA Stat : v3.2 on BBID : 0x86
DRAM not initialized , configure DRAM Settings
DRAM EmiReq Ok , 0x00B8
DRAM Init Ok , 0x40000000
DA Sent. Configure setting now ...
DA start Failed at final stage!
Check battery , cable , drivers and try try again
Boot Error!
Operation Failed
Elapsed: 00:00:08
Reconnect Power/Cable!
При выборе того-же MT6589_Android_scatter_emmc.txt программами SP_Flash_Tool_v5.1548.00.000 и SP_Flash_Tool_v3.1344.0.212, так-же не подгружается один из файлов (preload.img). Но в этом варианте мы имеем возможность выбрать файл в ручную и благополучно прошить. Будет ли возможность в будущем, ручной режим выбора файлов?
Знаю что SP_Flash_Tool в помощь, но как-то понравился мне этот Швейцарский нож:).
beeline tab pro unlock done
Phone found! [ 10 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6582
BB_CPU_HW : CB00
BB_CPU_SW : 8A00
BB_CPU_SB : 0001
BB_CPU_NM : [MediaTek] MT6582_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 45010053454D3038470F323732348179
DA Stat : v4.2 on BBID : 0x87
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0045 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , G80ME
[eMMC] : FLASH_CID : 45010053454D3038470F323732348179
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001D2000000
[eMMC] : FLASH_UCP : 7456 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Lock Status : Locked!
Unlocking ...
Unlock done!
MobilaGSM
17.02.2016, 21:52
Micromax D320 версия 1.41, при Reset Private Lock подвисает с ошибкой, пробовал раз 6. Версия 1.40 сделал все без ошибки с 1 раза.
--
"]Operation : Reset Privacy Lock [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 13 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 90014A4834473261110108B51A0E320B
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , a2G4
[eMMC] : FLASH_CID : 90014A4834473261110108B51A0E320B
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Checking data ...
Privacy Lock reset Ok!
Done!
Elapsed: 00:00:26
Reconnect Power/Cable!
p.s. Win10x64
MobilaGSM
17.02.2016, 22:03
Вдогонку Alcatel One Touch 5036D
--
та же история 1.40 бэкапит, 1.41 подвисает
--
v 1.40"]Chinese Miracle II [MTK module] v 1.40
Operation : Read ProInfo [ v1.40 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 13 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 1501004E35575A4D420192DAD014215D
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0015 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , BMZW5
[eMMC] : FLASH_CID : 1501004E35575A4D420192DAD014215D
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
PRO INFO :
Model : 5036D
PID : 2CMSRU1
Read Ok, MT6572_5036D_2CMSRU1_eMMC.alpro saved
Done!
Elapsed: 00:00:19
Reconnect Power/Cable!
ogvozdyk
21.02.2016, 20:20
1.41 планшет JEKA JK703 3G. Ифу прочел.
Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 8801034E436172642023724C45559107
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x88 , OEM : 0103
[eMMC] : FLASH_INF : [FORESEE] , draC
[eMMC] : FLASH_CID : 8801034E436172642023724C45559107
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000000E7400000
[eMMC] : FLASH_UCP : 3700 MiB [eMMC 4 GiB]
DEV RID : 7ED46E12C908878F4071FC8BBBBBAB23
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : JEKA
ProdName : JK703 3G
ProdModel : JK703 3G
Device : JK703 3G
AndroidVer: 4.2.2
MTKxCPU : MT6572
MTKxPRJ : ALPS.JB3.MP.V1.8
SECURITY :
IMEI_SW [1] : 865303021759487
IMEI_SW [2] : 865303021759495
BTMAC Addr : 000046657201
WiFi MAC : 003A8F69A247
MODEM :
BaseBand : MT6572_S00_MOLY_WR8_W1315_MD_WG_MP_V4_P1_1_wg_n
EXTRA :
LCD [0] : rgb_6572
LCD Res : 480x800
TOUCH [0] : K7_WVGA_YLD_COMBO_1680F
CAM [0] : gc0311_yuv
CAM [1] : gc0328_yuv
CAM [2] : gc2035_yuv
CAM [3] : gc0329_yuv
CAM [4] : gc0308_yuv
CAM [5] : gc0308_front_yuv
CAM [6] : sp0838_yuv
CAM [7] : sp00838_yuv
CAM [8] : siv121du_yuv
MODEM : K7_PCBV1P1_B1258
LOCALE : ru_RU zh_CN en_US es_ES fa_IR zh_TW pt_BR fr_FR de_DE tr_TR it_IT in_ID ms_MY vi_VN ar_EG th_TH pt_PT nl_NL el_GR hu_HU tl_PH ro_RO cs_CZ iw_IL my_MM km_KH ko_KR hdpi mdpi ldpi
Done!
Read NVRAM ошибка.
Wait for phone...
Phone found! [ 10 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 8801034E436172642023724C45559107
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x88 , OEM : 0103
[eMMC] : FLASH_INF : [FORESEE] , draC
[eMMC] : FLASH_CID : 8801034E436172642023724C45559107
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000000E7400000
[eMMC] : FLASH_UCP : 3700 MiB [eMMC 4 GiB]
DEV RID : 7ED46E12C908878F4071FC8BBBBBAB23
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[Info] : BaseBand : MT6572_S00_MOLY_WR8_W1315_MD_WG_MP_V4_P1_1_wg_n
Fatal error, buffer empty! Phone connection lost???
Read Error , something went wrong
Operation Failed
Сколько раз пробовали? у меня некоторые планшеты с 5-6 раза нормально видятся, проблема кривых драйверов, отвал усб портов на долисекунды
MobilaGSM
22.02.2016, 22:15
Сколько раз пробовали? у меня некоторые планшеты с 5-6 раза нормально видятся, проблема кривых драйверов, отвал усб портов на долисекунды
Склоняюсь к проблемной версии 1.41, попробовать почитать 1.40 и сделать вывод.
Лог успешной операции -снятие backup и с помощью него, восстановление телефона с отсутствующей модемной частью.
Operation : Read Flash [ v1.41 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 18 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 45010053454D3136479082628F5F90DD
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , G61ME
[eMMC] : FLASH_CID : 45010053454D3136479082628F5F90DD
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000003B5400000
[eMMC] : FLASH_UCP : 15188 MiB [eMMC 16 GiB]
DEV RID : 6D8CB20E102508328C585C7A05C1567D
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Conent now ...
Brand : V3
ProdName : V3
ProdModel : V3
Device : CXQ
AndroidVer: 4.4.2
MTKxCPU : MT6582
MTKxPRJ : cxq_inew_v3w_v1.0.10
[Read Ok] : preloader_eastaeon82_wet_kk.bin
[Read Ok] : MBR
[Read Ok] : EBR1
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Make Ok] : cache.img
[Make Ok] : userdata.img
[ScatCFG] : MT6582 / V1.1.1 / eastaeon82_wet_kk / EMMC
Android Info saved
MAUI Meta DB saved
HWConfig Info saved
FW Size : 1048 MiB
Scatter saved to : F:\Phone\Phone\Infiniti\Новая папка\MT6582__V3__V3__CXQ__4.4.2__cxq_inew_v3 w_v1.0.10\
All done!
Scatter Load Ok , BaseBand : MT6582 , Project : eastaeon82_wet_kk , Storage : EMMC
Files found : 11 , Set to Flash : 10
Created by Infinity-Box (c) Chinese Miracle II (c) 2016
Device Brand : V3
Device Model : CXQ
Device CPU : MT6582
Device IntName : V3
Device Version : 4.4.2
Device Compile : 22.07.2014 1:46:40
Device Project : cxq_inew_v3w_v1.0.10
Device ExtInfo : V3
Ready to Flash!
Operation : Flash [ v1.41 ]
======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 18 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 45010053454D31364790535791727081
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , G61ME
[eMMC] : FLASH_CID : 45010053454D31364790535791727081
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000003B5400000
[eMMC] : FLASH_UCP : 15188 MiB [eMMC 16 GiB]
DEV RID : CE709281554645C2339646B38AE1AADE
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
ScatCFG : BaseBand : MT6582 , Project : eastaeon82_wet_kk , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC supported by BootLoader!
BL : BatteryLevel : 3802 mV
BL : BatteryLevel Ok
BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000001400000-0x0000000000100000
Erase : 0x0000000003100000-0x00000003B1220000
Flash Pre-Erase Done, time used : 00:00:09
SecCfg Passed , 1799
BMT remark not need. Will skip
Sending Preloader ...
Use : preloader_eastaeon82_wet_kk.bin
Preloader Sent , Init passed
SecCfg Passed , 1799
PartCount : 0012
Update PMT by user request
Repartition Done!
Processing : Flash Write
Flash now : MBR
Image Flash Ok
Flash now : EBR1
Image Flash Ok
Flash now : UBOOT
Image Flash Ok
Flash now : BOOTIMG
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SEC_RO
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : ANDROID
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USRDATA
Image Flash Ok
Flash Write Done, time used : 00:02:22
Processing : Verify
Verify Passed : MBR
Verify Passed : EBR1
Verify Passed : UBOOT
Verify Passed : BOOTIMG
Verify Passed : RECOVERY
Verify Passed : SEC_RO
Verify Passed : LOGO
Verify Passed : ANDROID
Verify Passed : CACHE
Verify Passed : USRDATA
Data Verify Done, time used : 00:01:31
Update Mirror PMT
Update Done!
Update RomInfo done
Done!
Склоняюсь к проблемной версии 1.41, попробовать почитать 1.40 и сделать вывод.
Саш у меня и на 1.39-40 с планшетами были глюки подключения, надо тестировать
Power Supply
23.02.2016, 19:04
Склоняюсь к проблемной версии 1.41, попробовать почитать 1.40 и сделать вывод.
Так JayDi писал, что в версии 1.41 "немного" переборщил с проверками, в следующем релизе обещал исправить. NVRAM не читает, пробовал на нескольких аппаратах.
Operation : Read NVRAM [ v1.41 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 5 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : FE014E503058585858101E1C6270C0D5
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0xFE , OEM : 014E
[eMMC] : FLASH_INF : [MICRON] , XXXX0
[eMMC] : FLASH_CID : FE014E503058585858101E1C6270C0D5
[eMMC] : FLASH_BRT : 0x00100000 , 0x00100000 , 0x00100000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : CBB1DE8B824958EB854CD930F9C5DFB2
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[Info] : Can't identify BB version!
Fatal error, buffer empty! Phone connection lost???
Read Error , something went wrong
Operation Failed
Elapsed: 00:00:14
Reconnect Power/Cable!
McAlister
15.03.2016, 09:42
ZTE Blade Q Lux 3G принесли заблокированным (при вкл просит код безопасности). Wipe Data\Factory Reset и Operation : Clear UserLocks [Pin/Pwd/Pattern/FVLock/GoogleAcc] от кода не избавили. Код удачно удален при помощи операции "Reset Privacy Lock"
Start at : [14.03.2016 / 21:56:40]
Operation : Reset Privacy Lock [ v1.43 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 14 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040501A2D18A622D
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164040501A2D18A622D
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : 6E6A6BC2CA1A112A856E56ADEAA8B375
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Checking data ...
Privacy Lock reset Ok!
Done!
Elapsed: 00:00:28
Reconnect Power/Cable!
Finish at : [14.03.2016 / 21:57:08]
Лог Read Info
Start at : [14.03.2016 / 21:51:22]
Operation : Check / Read Info [ v1.43 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 14 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 90014A4834473164040501A2D18A622D
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164040501A2D18A622D
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : 6E6A6BC2CA1A112A856E56ADEAA8B375
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : ZTE
ProdName : P632A10
ProdModel : ZTE Blade Q Lux
Device : P632A10
AndroidVer: 4.4.2
MTKxCPU : MT6572
MTKxPRJ : LIFE_BY_QB18D_P632A10V1.0.0
SECURITY :
IMEI_SW [1] : 86713402блабла
IMEI_SW [2] : 86713402блабла
BTMAC Addr : D437D791F19B
WiFi MAC : EC1D7FADC26F
MODEM :
BaseBand : MT6572_S00_MOLY_WR8_W1315_MD_WG_MP_V36_P23_1_wg_n
EXTRA :
LCD [0] : ili9806e_fwvga_dsi_vdo_r453_hlt
LCD [1] : nt35512_fwvga_dsi_vdo_m453
LCD [2] : fl10802_fwvga_dsi_vdo_r453_unico
LCD [3] : ili9806e_fwvga_dsi_vdo_r453_hlt_ips
LCD [4] : ili9806e_fwvga_dsi_vdo_r453_yashi
LCD Res : 854x480
TOUCH [0] : msg2138a_fwvga
CAM [0] : t8ev5_yuv
CAM [1] : t8ev5sjc_yuv
CAM [2] : gc2145_yuv
CAM [3] : at2250_yuv
MODEM : ztenj72_we_72_kk_hspa_18
LOCALE : ru_RU en_US cs_CZ da_DK de_AT de_CH de_DE el_GR en_AU en_GB es_ES es_US fi_FI fr_CH fr_FR hu_HU it_IT lt_LT lv_LV nl_NL nb_NO pl_PL pt_BR pt_PT sv_SE zh_CN zh_TW uk_UA
Done!
Elapsed: 00:00:14
Reconnect Power/Cable!
Finish at : [14.03.2016 / 21:51:36]
ogvozdyk
15.03.2016, 10:48
Был Alcatel OT-3040G.Полностью рабочий. При считывании инфы зависает прога 1.41 и 1.40.
.:: Скрытый текст (вы должны войти под своим логином или зарегистрироваться и иметь 1 сообщение(ий)) ::.
Beeline_Fast unlock
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 67 ]
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6735
BB_CPU_HW : CA00
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6735_S00
Processing BROM stage
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 5600017030303031E8145038AF124820
DA Stat : v4.2 on BBID : 0x93
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0070 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 80001
[eMMC] : FLASH_CID : 7001005631303030385014E8204872AF
[eMMC] : FLASH_EXT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000001C3000000
[eMMC] : FLASH_UCP : 7216 MiB
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Lock Status : Locked!
Unlocking ...
Unlock done!
Китайский планшет. Модель - ioco i9100. После формата - стерт preloader ((
========================= Start =========================
13.03.2016 / 12:31:57
================================================== =======
Chinese Miracle II [MTK module] v 1.41
Start at : [13.03.2016 / 12:33:08]
Operation : Format FileSystem [ v1.41 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 205 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 8801034E4361726420200E55B513814D
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x88 , OEM : 0103
[eMMC] : FLASH_INF : [FORESEE] , draC
[eMMC] : FLASH_CID : 8801034E4361726420200E55B513814D
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000000E7400000
[eMMC] : FLASH_UCP : 3700 MiB [eMMC 4 GiB]
DEV RID : 74C2BD802C5EE08ABBA97DAFB46E65DA
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!
Done!
Elapsed: 00:00:24
Reconnect Power/Cable!
Finish at : [13.03.2016 / 12:33:32]
Start at : [13.03.2016 / 12:34:07]
Operation : Check / Read Info [ v1.41 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 276 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 8801034E4361726420200E55B513814D
Initialize Memory ...
[DA_ERROR] : DRAM Configure failed!
ErroCode : 0x2003
EMICFG_NOT_FOUND
TRY NOT HOLD VOLUME(+/-) KEYS ON CONNECT!
Boot Error!
Huawei Ascend Y511-U10 UNLOCK
Sync...
Inital regs read done
Boot Info :
BB_CPU_ID : 6572
BB_CPU_HW : CA01
BB_CPU_SW : 8A00
BB_CPU_SB : 0000
BB_CPU_NM : [MediaTek] MT6572_S00
Processing BROM stage
BLVersion : 0x01
SecCfgVal : 0x00000000
BromVersion : 0xFF
BLVersion : 0x01
Preloader Status : Alive
Processing DA stage
DA Select done , sending
DA Ver : MTK_AllInOne_DA_v5.1540.01.01
NAND_ID : 00000000000000000000000000000000
eMMC_ID : 90014A4834473164048602A2A83CA057
DA Stat : v4.2 on BBID : 0x88
DA Sent. Configure setting now ...
DA started successuflly
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0090 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , d1G4
[eMMC] : FLASH_CID : 90014A4834473164048602A2A83CA057
[eMMC] : FLASH_EXT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Lock Status : Locked!
Unlocking ...
Unlock done!
Done!
Elapsed: 00:00:29
Reconnect Power/Cable!
Добавлено через 42 часа 35 минут
Билайн Смарт 5 UNLOCK 29 Секунд
Wait for phone...
Phone found! [ 77 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 45010053454D3034473AFD70EB0192B9
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , G40ME
[eMMC] : FLASH_CID : 45010053454D3034473AFD70EB0192B9
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID : 62C63AA331CD884DA4AB1E3C03197BEE
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
SIM Lock Status : Locked!
Unlocking now ...
Unlock done!
Done!
Elapsed: 00:00:29
Reconnect Power/Cable!
Lenovo p780 write security на версии 1.44 завершалось ошибкой .Версия 1.39 сделала с первого раза.
ps/ может хоть кому сэкономит время
fly iq442
Read Flash
Wait for phone...
Phone found! [ 87 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6575
BB_CPU_NME : [MediaTek] MT6575|MT6577_S00
BB_CPU_EXT : 0xCB00 , 0x8B00 , 0xE201
Processing BROM stage
i2c Init : 00008810
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x02
WD Disable stat : 0x0000
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x84
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594812A181057B9FA1
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 5D522805E739A0F466F96A91A50BEFD1
INT RAM : 0x00020000
EXT RAM : 0x00000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
USBDL : Init HSUSB Ok!
Read Ok , collect info
Brand : FLY
ProdName : s8073
ProdModel : Fly_IQ442
Device : s8073
AndroidVer: 4.0.4
MTKxCPU : MT6577
MTKxPRJ : ALPS.ICS2.MP.V1
Saved to : C:\Users\Администратор\Desktop\samsun g\Новая папка (2)\MT6577__FLY__Fly_IQ442__ALPS.ICS2.MP.V1__Andro id_4.0.4.ispff
Read NVRAM
Wait for phone...
Phone found! [ 87 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6575
BB_CPU_NME : [MediaTek] MT6575|MT6577_S00
BB_CPU_EXT : 0xCB00 , 0x8B00 , 0xE201
Processing BROM stage
i2c Init : 00008810
SpeedSet : 0000
VChrgSet : 0x28 , BatStat : 0x02
WD Disable stat : 0x0000
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.3.2 on BBID : 0x84
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , HYNIX
[eMMC] : FLASH_CID : 90014A2058494E594812A181057B9FA1
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000E7000000
[eMMC] : FLASH_UCP : 3696 MiB [eMMC 4 GiB]
DEV RID : 5D522805E739A0F466F96A91A50BEFD1
INT RAM : 0x00020000
EXT RAM : 0x00000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
USBDL : Init HSUSB Ok
[Info] : Can't identify BB version!
Read Ok, MT6575_eMMC.spnv saved
BILAYN SMART 5 UNLOCK
Wait for phone...
Phone found! [ 11 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1552.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 45010053454D3034473A0D6D516B5269
Initialize Memory ...
DRAM configured from IDB!
DRAM initialize passed!
DRAM size : 0x20000000
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x45 , OEM : 0100
[eMMC] : FLASH_INF : [SANDISK] , G40ME
[eMMC] : FLASH_CID : 45010053454D3034473A0D6D516B5269
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00200000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID : 7CE0C9C9601101FE436408E469EA5DF0
INT RAM : 0x00020000
EXT RAM : 0x20000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
USBDL : Init HSUSB Ok
SIM Lock Status : Locked!
Unlocking now ...
Unlock done!
Done!
Elapsed: 00:00:42
Reconnect Power/Cable!
BOTIR , Зачем выкладывать логи тех аппаратов которые давно уже изъезжены , все и так понимают что софт их делает на ура , тема создана для теста так сказать редких моделей, иначе это выглядит как набивка постов не иначе.
Zte X3(T620), принесли с проблемой активации, стояла версия 1.44, не дала ничего сделать, ошибка идентификации памяти итп, flashtool тоже послал. Версия 1.46 сбросы сделал, тел рабочий
Dr_Wolodya
19.05.2016, 17:20
Оценил функцию переразметки памяти (User Memory Repartition).
Принесли Lenovo A850. Стоит microSD 32Gb, внутренний накопитель на 2,5Gb, на который можно снимать видео и фотки, и 300Мб!!! памяти для установки приложений. Издевательство.
Сделал переразметку и теперь 2,9Gb для приложений, а фотки и видео снимаются на microSD 32Gb:Operation : Repart User Memory [ v1.47 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6582
BB_CPU_NME : [MediaTek] MT6582_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1612.01.01
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x87
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004B355530304D02F52BC699A011
Initialize Memory ...
DRAM already initialized by Preloader
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x15 , OEM : 0100
[eMMC] : FLASH_INF : [SAMSUNG] , M00U5
[eMMC] : FLASH_CID : 1501004B355530304D02F52BC699A011
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00020000
[eMMC] : FLASH_LEN : 0x00000000E9000000
[eMMC] : FLASH_UCP : 3728 MiB [eMMC 4 GiB]
DEV RID : DBD2B004EAFDBE10E9D0659316C2BAB4
INT RAM : 0x00020000
EXT RAM : 0x40000000
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Available Internal Memory : 2,90 GiB
Memory settings detected , waiting user decision
Memory size set, initialize new settings
Structure detection passed successfully
Init passed! Power On phone to accept changes!
Done!
Elapsed: 00:00:32
Reconnect Power/Cable!
Паша, спасибо! :appl:
Не надо так делать, 10 процентов оставляйте в разделе принесут обратно с бутлупом.Вдаваться в подробности не буду, но факты есть - 10 процентов с хвоста оставлять надо.
Turboxxx
12.03.2017, 18:41
Китаец Samsung S6 MT6571 считывается full и прошивка, но прошить не дает:
Operation : Read Flash [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 28 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 00AD00BC00900055005400AD00BC0000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x008B , [HYNIX] H9DA4VH2GJAMCR_4EM
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0054 00AD 00BC
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/01/NIM_Px-2
DEV RID : 0xEC07E3597A3BDBC19A1C6546E8CE54E6
INT RAM : 0x00020000
EXT RAM : 0x10000000 [256 MiB]
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
Read Ok , collect info
MTKxCPU : MT6571
MTKxPRJ : benrui71_e_lca
Saved to : C:\2\111\MT6571__benrui71_e_lca.ispff
Done!
Elapsed: 00:04:57
Reconnect Power/Cable!
Load File
Bad file detected!
Точно так же со MT6571_Android_scatter, но flashtool прошивает
Operation : Read Flash [ v1.58 ]
Power Off Phone , re-connect battery , Insert USB cable!
Wait for phone...
Phone found! [ 28 ]
Sync...
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 28 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 00AD00BC00900055005400AD00BC0000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x008B , [HYNIX] H9DA4VH2GJAMCR_4EM
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0054 00AD 00BC
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/00/NIM_Px-2
DEV RID : 0xEC07E3597A3BDBC19A1C6546E8CE54E6
INT RAM : 0x00020000
EXT RAM : 0x10000000 [256 MiB]
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
[Read Ok] : preloader_benrui71_e_lca.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : usrdata.img
[ScatCFG] : MT6571 / V1.1.1 / benrui71_e_lca / NAND
FW Size : 333 MiB
Brand : alps
ProdName : benrui71_e_lca
ProdModel : MT6571
Device : benrui71_e_lca
AndroidVer: 4.2.2
MTKxCPU : MT6571
MTKxPRJ : ALPS.JB7.MP.V1.14
Android Info saved
Scatter saved to : C:\2\111\MT6571_NAND_alps__MT6571__benrui71_e_lca_ _4.2.2__ALPS.JB7.MP.V1.14
Done!
Elapsed: 00:03:34
Reconnect Power/Cable!
Unsupported Yet( or bad??? ) file selected!
Мучения продолжаются, хочется полностью восстановить: сеть 3g (wcdma) - не дает выбрать и анимацию загрузки и т.д., но CM2 упорно не хочет дать выбрать считанный full. Каким способом считать полный дамп и записать на MT6571?
Китаец Samsung S6 MT6571 считывается full и прошивка, но прошить не дает:
Operation : Read Flash [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 28 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 00AD00BC00900055005400AD00BC0000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x008B , [HYNIX] H9DA4VH2GJAMCR_4EM
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0054 00AD 00BC
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/01/NIM_Px-2
DEV RID : 0xEC07E3597A3BDBC19A1C6546E8CE54E6
INT RAM : 0x00020000
EXT RAM : 0x10000000 [256 MiB]
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
Read Ok , collect info
MTKxCPU : MT6571
MTKxPRJ : benrui71_e_lca
Saved to : C:\2\111\MT6571__benrui71_e_lca.ispff
Done!
Elapsed: 00:04:57
Reconnect Power/Cable!
Load File
Bad file detected!
Точно так же со MT6571_Android_scatter, но flashtool прошивает
Operation : Read Flash [ v1.58 ]
Power Off Phone , re-connect battery , Insert USB cable!
Wait for phone...
Phone found! [ 28 ]
Sync...
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 28 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6571
BB_CPU_NME : [MediaTek] MT6571_S00
BB_CPU_EXT : 0xCA00 , 0x8D00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x8B
NAND Flash : 00AD00BC00900055005400AD00BC0000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x008B , [HYNIX] H9DA4VH2GJAMCR_4EM
[NAND] : FLASH_DIE : 00AD 00BC 0090 0055 0054 00AD 00BC
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 0800/0040/00/NIM_Px-2
DEV RID : 0xEC07E3597A3BDBC19A1C6546E8CE54E6
INT RAM : 0x00020000
EXT RAM : 0x10000000 [256 MiB]
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
[Read Ok] : preloader_benrui71_e_lca.bin
[Read Ok] : lk.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : logo.bin
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : usrdata.img
[ScatCFG] : MT6571 / V1.1.1 / benrui71_e_lca / NAND
FW Size : 333 MiB
Brand : alps
ProdName : benrui71_e_lca
ProdModel : MT6571
Device : benrui71_e_lca
AndroidVer: 4.2.2
MTKxCPU : MT6571
MTKxPRJ : ALPS.JB7.MP.V1.14
Android Info saved
Scatter saved to : C:\2\111\MT6571_NAND_alps__MT6571__benrui71_e_lca_ _4.2.2__ALPS.JB7.MP.V1.14
Done!
Elapsed: 00:03:34
Reconnect Power/Cable!
Unsupported Yet( or bad??? ) file selected!
на этих процессорах (MT6571) именно так.
попробуй версию 1.57.
Turboxxx
12.03.2017, 19:40
на этих процессорах (MT6571) именно так.
попробуй версию 1.57.
Chinese Miracle II [MTK module] v 1.57
Load File
Bad file detected!
Так же, а очень надо считать именно full и залить в точно такой же. NV так же читает, но не пишет.
drakomag
03.06.2017, 15:04
Alcatel 4034x MT6580
Operation : Read NVRAM [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 43 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 110100303034474530001809A97973EB
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x11 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 0EG40
[eMMC] : FLASH_CID : 110100303034474530001809A97973EB
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID : 0x4E5D5B4D4C5FD20854ABCB7E37BC0AD1
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
NVM Read Ok, 4034x MT6580_eMMC.spnv
Done!
Elapsed: 00:00:32
Reconnect Power/Cable!
Operation : Read Flash [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 43 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 110100303034474530001809A97973EB
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x11 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 0EG40
[eMMC] : FLASH_CID : 110100303034474530001809A97973EB
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID : 0x4E5D5B4D4C5FD20854ABCB7E37BC0AD1
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Reading Flash Content now ...
xGPT : Normalize settings Ok!
[Read Ok] : preloader_pixi4_4.bin
[Read Ok] : lk.bin
[Read Ok] : logo.bin
[Read Ok] : boot.img
[Read Ok] : recovery.img
[Read Ok] : secro.img
[Read Ok] : system.img
[Read Ok] : cache.img
[Read Ok] : userdata.img
[ScatCFG] : MT6580 / V1.1.2 / pixi4_4 / EMMC
Android Info saved
HWConfig Info saved
FW Size : 1106 MiB
Scatter saved to : C:\Users\Administrator\Downloads\MT6580______\
All done!
Done!
Elapsed: 00:04:47
Reconnect Power/Cable!
Scatter Load Ok , BaseBand : MT6580 , Project : pixi4_4 , Storage : EMMC
Files found : 9 , Set to Flash : 8
Ready to Flash!
Start at : [19.05.2017 / 14:20:40]
Operation : Flash [ v1.58 ]
======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 43 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 110100303034474530001809A97973EB
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x11 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 0EG40
[eMMC] : FLASH_CID : 110100303034474530001809A97973EB
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID : 0x4E5D5B4D4C5FD20854ABCB7E37BC0AD1
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
ScatCFG : BaseBand : MT6580 , Project : pixi4_4 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Skip checking by User request!
BL : BatteryLevel : 3755 mV
BL : BatteryLevel Ok
Backup enabled!
Backup saved : Backup\Flash\110100303034474530001809A97973EB\
BL : Flash Pre-Erase
Total blocks to Erase : 2
Erase : 0x0000000002780000-0x0000000006080000
Erase : 0x0000000009800000-0x00000000DEC80000
Flash Pre-Erase Done, time used : 00:00:01
SecCfg Passed , 1799
BMT remark not need. Will skip
Preloader Download skipped by user request!
PartCount : 0016
Update PMT by user request
Repartition Done!
Use FLN Mode
Processing : Flash Write
Flash now : LK
Image Flash Ok
Flash now : LOGO
Image Flash Ok
Flash now : BOOT
Image Flash Ok
Flash now : RECOVERY
Image Flash Ok
Flash now : SECRO
Image Flash Ok
Flash now : SYSTEM
Image Flash Ok
Flash now : CACHE
Image Flash Ok
Flash now : USERDATA
Image Flash Ok
Flash Write Done, time used : 00:04:12
Processing : Verify
Verify Passed : LK
Verify Passed : LOGO
Verify Passed : BOOT
Verify Passed : RECOVERY
Verify Passed : SECRO
Verify Passed : SYSTEM
Verify Passed : CACHE
Verify Passed : USERDATA
Data Verify Done, time used : 00:00:07
Update Mirror PMT
Update Done!
Update RomInfo done
Done!
Elapsed: 00:04:44
Reconnect Power/Cable!
Operation : Format FileSystem [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 43 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x94
NAND Flash : NOT INSTALLED
eMMC Flash : 110100303034474530001809A97973EB
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x11 , OEM : 0100
[eMMC] : FLASH_INF : [TOSHIBA] , 0EG40
[eMMC] : FLASH_CID : 110100303034474530001809A97973EB
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000EC000000
[eMMC] : FLASH_UCP : 3776 MiB [eMMC 4 GiB]
DEV RID : 0x4E5D5B4D4C5FD20854ABCB7E37BC0AD1
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Clear FRP ( Google Reset Protection )
Clear Ok!
Clear DIN
Clear Ok!
Clear USERDATA
Clear Ok!
Clear CACHE
Clear Ok!
Done!
Elapsed: 00:00:25
Reconnect Power/Cable!
Прошивка слитая с Doogee T5 2017/07/26 Android 6.0 Гугл (https://drive.google.com/file/d/1PELdl01cytmdgJG5i6JCKL3XLpLh-182/view)
reated by Infinity-Box (c) Chinese Miracle II (c) 2016 :)
vBulletin® v3.8.7, Copyright ©2000-2024, Jelsoft Enterprises Ltd. Перевод: zCarot