E5-00 только вибро...

[Сулейман]

Здравствуйте товарищи,принесли сей телефон с диагнозом не включается,при включении срабатывает только вибро,в локал не входит.Думал прошить,воткнул USB кабель в коннетор телефона не подключив к ПК и просто случайно нажал кнопку включения телефона,и о чудо телефон включился и нормально работает,но поработав не продолжительное время снова вырубился,и заряжался как-то не корректно,с низким зарядом АКБ писал "отсоедините ЗУ для экономии электроэнергии",коннектор USB при визуальном осмотре в норме,потом промыл почистил телефон нормально заработал,отдал клиенту на второй день пришел с такой-же проблемой,но теперь чистка не помогла.Окислы на плате были еле заметные.Проц и КП на компаунде,вокруг них вообще окислов нет.Сделал бекапы в мертвом режиме и стер аппарат полностью,после залил SW локала так и не стало.Если после заливки одного SW локала нет значит ПО не причем ?

[uo5oq]

То, что ПО не причем, было ясно сразу после "чудесного" ВКЛючения.
Шить, а тем более стирать не нужно было.

[KonstantinVoskr]

Логи на всяк случай дайте.

[mr treexel]

Как вариант - d3300 (заодно n3301 и n3302) и n7560

[Сулейман]

Как вариант - d3300 (заодно n3301 и n3302) и n7560

Вариантов много,надо сперва питание вторичных цепей проверить наверно?

Добавлено через 10 часов 55 минут
Логи на всяк случай дайте.

Вот FullErase:
Connect phone on selected interface...

User ACCEPTED FULL ERASE
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02

- > Backup check skipped by user

Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : CCD9F80559BA50D9B3E274F9E7120BE1EE4EEA7C

Reading NPC certificate...
IMEI : 000000000000000
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...

ADL: Preparing for erase...

Full Erase started...
Asic : CMT , Sub : NAND
Erase Area 0x00000000-0x1FFFFFFF
Erasing Ok , [0F]
Erase done , time : 00:00:06

ADL: Erase done

ADL: Close_Session
Content: 000205000000000000FFFF00000000
ADL: Reboot
Phone disconected!


Прошивка:
Core : v1.98 , BB5XG FlashEngine : v9.9

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm632_081.004_prd.core.fpsx
PPM : rm632_081.004_54.01_Russian_QW1_x3_prd.rofs2.fpsx
PPM2 : rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
CNT : rm632_081.004_U005.000_prd.uda.fpsx
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...

- > No any CRT data (MCU damaged/CERT erased), skip saving


=== SW Version Check ===
- > Can not collect initial info, continue flashing...
- > Hope, this version will be ok
=== SW Version Check ===

===Flashing [MCU]===
Erase : Processing rm632_081.004_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing rm632_081.004_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 436 blocks
TIME : Write time : 00:00:14
MCU Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [PPM]===
Erase : Processing rm632_081.004_54.01_Russian_QW1_x3_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm632_081.004_54.01_Russian_QW1_x3_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 222 blocks
TIME : Write time : 00:00:08
PPM Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [PPM2]===
Erase : Processing rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 35 blocks
TIME : Write time : 00:00:01
PPM Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [CNT]===
Erase : Processing rm632_081.004_U005.000_prd.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing rm632_081.004_U005.000_prd.uda.fpsx
Total writen 97 blocks
TIME : Write time : 00:00:05
CNT Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:35
Reboot phone now...

- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy

[KonstantinVoskr]

Почему после стирания перед прошивкой не пролили ПО из пакета E5-00 RM-632 stress test 042.005 v1.0 ?

[Сулейман]

Почему после стирания перед прошивкой не пролили ПО из пакета E5-00 RM-632 stress test 042.005 v1.0 ?

У меня нет этого пакета,что это за ПО,ENO файл что-ли?

[KonstantinVoskr]

Вы издеваетесь что ли?
Окей, ня ... (http://google.gik-team.com/?q=E5-00+RM-632+stress+test+042.005+v1.0+)

[Сулейман]

Вы издеваетесь что ли?
Окей, ня ... (http://google.gik-team.com/?q=E5-00+RM-632+stress+test+042.005+v1.0+)

Да скачал я его с другого файлообменника,что сразу минус то лепите,я уже совсем красный стал.Теперь еще один вопрос,как залить это ПО Stress Test,BEST не видит эти файлы.Плюс еще ENO файл скачал на него "E5_ENO_WK2012_v034".

Добавлено через 12 минут
Вот получилось вроде прошить,гляньте лог:
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm632_Substrate_test_10w14_v5.1_PRD.cmt
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Transmission type request fail [000000]
-> Boot error... :(
-> Boot fail...
Flashing failed...

Phone disconected!

Connect phone on selected interface...

Core : v1.98 , BB5XG FlashEngine : v9.9

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm632_Substrate_test_10w14_v5.1_PRD.cmt
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...

- > No any CRT data (MCU damaged/CERT erased), skip saving


=== SW Version Check ===
- > Can not collect initial info, continue flashing...
- > Hope, this version will be ok
=== SW Version Check ===

===Flashing [MCU]===
Erase : Processing rm632_Substrate_test_10w14_v5.1_PRD.cmt
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm632_Substrate_test_10w14_v5.1_PRD.cmt
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [SOS*ISASW]
Total writen 17 blocks
TIME : Write time : 00:00:00
MCU Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:00
Reboot phone now...

- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy

[Dr_Wolodya]

По-моему после erase и прошивки аппаратно исправный телефон должен включится и/или войти в Local mode. Если этого не произошло, то лить ENO/stress бесполезно.

[Сулейман]

Прогрев обвязки в районе USB коннектора и вуаля ТА включается.Вообщем теперь трабла его восстановить програмно,что-то BEST не может его по USB загружать в Local и Test реимы,незнаю почему.
Вот логи прошивка после FullErase и Stress Test:
Connect phone on selected interface...

Core : v1.98 , BB5XG FlashEngine : v9.9

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm632_081.004_prd.core.fpsx
PPM : rm632_081.004_20.01_Russian_QW1_prd.rofs2.fpsx
PPM2 : rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
CNT : rm632_081.004_U001.000_prd.uda.fpsx
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...

- > No any CRT data (MCU damaged/CERT erased), skip saving


=== SW Version Check ===
- > Can not collect initial info, continue flashing...
- > Hope, this version will be ok
=== SW Version Check ===

===Flashing [MCU]===
Erase : Processing rm632_081.004_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing rm632_081.004_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 436 blocks
TIME : Write time : 00:00:14
MCU Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [PPM]===
Erase : Processing rm632_081.004_20.01_Russian_QW1_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm632_081.004_20.01_Russian_QW1_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 222 blocks
TIME : Write time : 00:00:07
PPM Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [PPM2]===
Erase : Processing rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 35 blocks
TIME : Write time : 00:00:01
PPM Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [CNT]===
Erase : Processing rm632_081.004_U001.000_prd.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing rm632_081.004_U001.000_prd.uda.fpsx
Total writen 97 blocks
TIME : Write time : 00:00:05
CNT Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:35
Reboot phone now...


И как видите телефон не грузится в нормальный режим по USB,хотя когда нажимаю кнопку включения,программа видит его,вот лог:
Elapsed: 00:02:36
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Resetting selected items...
Check phone mode...
Phone in RfInactive mode
Seting Test mode... wait...
Test mode set
Settings Full Factory Defaults...
Error When resetting Full factory :( ...
Settings Software Upgrade Defaults...
Error When setting Software Upgrade Defaults :( ...
Settings Service Centre Defaults...
Error When setting Service Centre defaults :( ...
Settings Production Tune Defaults...
Error When settinng Production Tune defaults :( ...
Settings User Data Defaults...
Error When setting User Data defaults :( ...
Settings Leave Factory defaults...
Error When setting Leave Factory Defaults :( ...

Elapsed: 00:01:00

Phone disconected!

Но при попытке сделать Factory Set послк того как BEST увидел ТА в NormalMode,снова программа не может его загрузить в TestMode,по ходу контроллер USB барахлит наверно.Его можно восстановить по Fbus?

[KonstantinVoskr]

По-моему после erase и прошивки аппаратно исправный телефон должен включится и/или войти в Local mode. Если этого не произошло, то лить ENO/stress бесполезно.
Насколько помню ENO/stress нужно лить после стирания и до прошивки основного ПО, а то будет совсем нехорошо аппарату.

[Сулейман]

Насколько помню ENO/stress нужно лить после стирания и до прошивки основного ПО, а то будет совсем нехорошо аппарату.

Одного Stress достаточно? А то ENO файл вообще не хочет литься ни BESTom ни Cyclonom.JAF нужен для ENO.

[Master_X]

ENO нужен обязательно. Stress это тестовый файл - по факту не нужен для поднятия тела после стирания(это для проверки железа).

[KonstantinVoskr]

Одного Stress достаточно? А то ENO файл вообще не хочет литься ни BESTom ни Cyclonom.JAF нужен для ENO.
А как вы думаете почему?


PS: не факт, что если даже с помощью JAF вы зальете его в аппарат, и вроде все как по маслу- а оно помогло...
PSS: логи не забывайте прикреплять, иначе можно как за флуд посчитать...

[Сулейман]

А как вы думаете почему?

И Cyclone и BEST пишет Bad Image,может по настоящему поврежденный файл?

[KonstantinVoskr]

И Cyclone и BEST пишет Bad Image,может по настоящему поврежденный файл?
Вы логи выкладывать будете или без этого (http://lurkmore.so/images/7/77/Book3jl0.jpg) вы не можете?


Насчет BEST. Когда то была подобная проблема, но ее пофиксили (http://www.mcrf.ru/forum/showpost.php?p=207503&postcount=73). Возможно она опять вылезла, но учитывая что еще и Cyclone ругается, тут уж однозначно ответить не представляется возможным. Тут Паша необходим.

PS: и последнее- версию BEST-а посвежее используйте, уже версия 2.10 как месяц лежит на поддержке.

[Сулейман]

Cyclone при попытке выбрать файл ENO сразу пишет лог:
Can't add E5_ENO_WK2012_v034.fpx_cry, Bad image

А BEST выбирает файл ENO,даже пытается его прошить,но все равно пишет вот лог:
Core : v1.98 , BB5XG FlashEngine : v9.9

Selected FlashSettings : Manual
[CRY] : FlashFile verify disabled

Files Set for Flashing :
MCU : E5_ENO_WK2012_v034.fpx_cry
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : CCD9F80559BA50D9B3E274F9E7120BE1EE4EEA7C
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
IMEI : 000000000000000
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...
===Flashing [MCU]===
Erase : Processing E5_ENO_WK2012_v034.fpx_cry
Checking flash content , please wait...
Checking flash done
Error: Erase/Write : Bad image file
Connect phone on selected interface...


Elapsed: 00:00:09
Connect phone on selected interface...

Уже две версии крякнутого Jafa скачал,последняя J.A.F_1.98.66_Beta5_Cracked_10.03.31,что-то нифига не получается его сконнектить с UFSom,в чем трабла?Крякнутый Jaf вообще не запускается,только появляется при запуске окно программы и ничего дальше,вот скрин jaf:
27971
Как настроить jaf?

[KonstantinVoskr]

Попробуйте этим


PS: хотелось бы узнать контрольную сумму вашего ENO.

[Сулейман]

Вот отлично получилось,сперва Full Erase,после залил Stress Test и файл Eno,вот лог заливки Eno выложенный уважаемым товарищем KonstantinVoskr:
Core : v1.98 , BB5XG FlashEngine : v9.9

Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
APE : RM632_ENO_APE_ONLY.fpsx
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...

- > No any CRT data (MCU damaged/CERT erased), skip saving


=== SW Version Check ===
- > Can not collect initial info, continue flashing...
- > Hope, this version will be ok
=== SW Version Check ===

===Flashing [APE]===
Erase : Processing RM632_ENO_APE_ONLY.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing RM632_ENO_APE_ONLY.fpsx
CMT: Writing Hash CERT [SOS*ENO]
Total writen 17 blocks
TIME : Write time : 00:00:00
APE Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:00
Reboot phone now...

- > AfterFlash Failed! :( Reason : Downgrade try or HW Error
Anyway - try reinsert battery and PowerUp phone manualy

Connect phone on selected interface...

Done!

После прошивка:
Selected FlashSettings : Manual
Check FlashFiles, Please, wait...

Files Set for Flashing :
MCU : rm632_081.004_prd.core.fpsx
PPM : rm632_081.004_20.01_Russian_QW1_prd.rofs2.fpsx
PPM2 : rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
CNT : rm632_081.004_U003.000_prd.uda.fpsx
Flashing phone now...
[Gen] Rules accepted for : RAPUxx Generation
Check files done...
-> SWversion check skipped : Dead mode selected
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : blank (Erased or HW failure)
ADL: phone is in flash mode

Backup enabled, will read all certificates...
Reading NPC certificate...
Reading CCC certificate...
Reading HWC certificate...
Reading R&D certificate...
Reading VARIANT certificate...
Reading PARTNERC certificate...
Reading MDM_KEYS certificate...

- > No any CRT data (MCU damaged/CERT erased), skip saving


=== SW Version Check ===
- > Can not collect initial info, continue flashing...
- > Hope, this version will be ok
=== SW Version Check ===

===Flashing [MCU]===
Erase : Processing rm632_081.004_prd.core.fpsx
Partitioning....
Partitioning Ok...
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing rm632_081.004_prd.core.fpsx
CMT: Writing Hash CERT [ADA]
CMT: Writing Hash CERT [KEYS]
CMT: Writing Hash CERT [PRIMAPP]
CMT: Writing Hash CERT [RAP3NAND]
CMT: Writing Hash CERT [SOS+PMML]
CMT: Writing Hash CERT [PASUBTOC]
CMT: Writing Hash CERT [PAPUBKEYS]
CMT: Writing Hash CERT [GENIO_INIT]
CMT: Writing Hash CERT [SOS*UPDAPP]
CMT: Writing Hash CERT [SOS*DSP0]
CMT: Writing Hash CERT [LDSP]
CMT: Writing Hash CERT [SOS*ISASW]
CMT: Writing Hash CERT [SOS+CORE]
CMT: Writing Hash CERT [SOS+ROFS1]
Total writen 436 blocks
TIME : Write time : 00:00:14
MCU Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [PPM]===
Erase : Processing rm632_081.004_20.01_Russian_QW1_prd.rofs2.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm632_081.004_20.01_Russian_QW1_prd.rofs2.fpsx
CMT: Writing Hash CERT [SOS+ROFS2]
Total writen 222 blocks
TIME : Write time : 00:00:07
PPM Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [PPM2]===
Erase : Processing rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:00
Write : Processing rm632_081.004_C00.01_DEFAULT_prd.rofs3.fpsx
CMT: Writing Hash CERT [SOS+ROFS3]
Total writen 35 blocks
TIME : Write time : 00:00:01
PPM Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

===Flashing [CNT]===
Erase : Processing rm632_081.004_U003.000_prd.uda.fpsx
Erasing....
Erasing Ok...
TIME : Erase time : 00:00:02
Write : Processing rm632_081.004_U003.000_prd.uda.fpsx
Total writen 97 blocks
TIME : Write time : 00:00:05
CNT Write done
ADL: Request programm status
NAND status : 00000002 / 00000002 / 00000000

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot

Flashing done!
Total flash time : 00:00:35
Reboot phone now...

Reading Phone Info....
Connected phone - Nokia E5-00
Software Info: V ICPR82_11w16.3.4 17-08-11 RM-632 (c) Nokia
IMEI: 12345610654321?
Ape Version: 081.004
Product code:
Wait, when phone will be ready ...
Checking...
SimLock status : SimLock is Ok
Security status : Security is Ok
Read Info Done!
Battery voltage is enough for start
AfterFlash operations done ;D
Done!

Elapsed: 00:01:50
Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------

IMEI Validation : IMEI Damaged!!!!
- > SIMLOCK , SECURITY Info can be wrong!
- > Need restore NPC backup or RPL


SDD Key status : SDData Damaged!!!!! :(
- > Do REPAIR SDD , Local SX4 if needed

CMLA Key status : CMLA key Not exist
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!

И наконец-то телефон загрузился в TestMode,начались анцы с бубном по восстановлению основного ПО:
Will Write RPL keys now...
Check RPL file...
SIMLOCK Data found!
SIMLOCK KEY found!
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:02
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : CCD9F80559BA50D9B3E274F9E7120BE1EE4EEA7C
ADL: Preparing for write certificates...


ADL: Writing Flash certs done! :)

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot
Wait, reconneting...

Writing SimLock Key... Error!
Writing SimLock Data... Error!

SDD Key status : SDData Damaged!!!!! :(
SimLock status : SimLock is Ok
Security status : Security is Ok


Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Phone disconected!

Connect phone on selected interface...

Will Write RPL keys now...
Check RPL file...
NPC Data found! (CMT)
CCC Data found! (CMT)
HWC Data found! (CMT)
Dead Mode is Selected
Waiting for USB device...
--- Insert cable and charger or press phone's power button! ---
Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : CCD9F80559BA50D9B3E274F9E7120BE1EE4EEA7C
ADL: Preparing for write certificates...

Erase NPC... Ok
Writing NPC... Ok
Erase CCC... Ok
Writing CCC... Ok
Erase HWC... Ok
Writing HWC... Ok

ADL: Writing Flash certs done! :)

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot

-> No any Flex keys selected, skip flex part

Done!

Phone disconected!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------

SDD Key status : SDData Damaged!!!!! :(
- > Do REPAIR SDD , Local SX4 if needed

CMLA Key status : CMLA key Not exist

SimLock status : SimLock Damaged!!!!! :(
- > Do REPAIR SL if it SL2/SL phone, if SL3 - Help Only Backup Or RPL

Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!

Repair SD procedure started...

Phone Imei: 351663054302617
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing Super Dongle Key... Ok!
Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
CMLA Key status : CMLA key Not exist

SimLock status : SimLock Damaged!!!!! :(
- > Do REPAIR SL if it SL2/SL phone, if SL3 - Help Only Backup Or RPL


Security status : Security Damaged!!!!! :(
- > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )

-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!

Local SX4 procedure started...

Check SD : Key is Ok
Phone Imei: 351663054302617
Key file exists, no need to read...
Step 1...
Step 2...
SX4 Auth fail...
- > "Custom Keys" enabled, try again now
- > If SDD original - "Use Server Sx4"


Local SX4 procedure started...

Check SD : Key is Ok
Phone Imei: 351663054302617
Key file exists, no need to read...
Step 1...
Step 2...
SX4 Auth fail...
- > "Custom Keys" enabled, try again now
- > If SDD original - "Use Server Sx4"


Will Write CCC/HWC keys now...

RM-632.rpl not exist
Select file, please
Using : 351663054302617_CRT.rpl
CCC Data found!
HWC Data found!

Connection opened successfully
Waiting for communication response...
[BootRom] : 1st boot Ok!
ASIC ID: 000000030000022600010007600C192102031104
CPU ID : RAPU v11 , Features : Dead-Test , USBRPL , FullUSB
EM0 ID: 00000C35
EM1 ID: 00000C30
PUBLIC ID: 02C0011870DE0344928010C97F5A0F6FADCD92AA
ASIC MODE ID: 00
ROOT KEY HASH: 916F75217F32081248B15C38DFC8E81B
ROM ID: E693EF0DAC22615B
Use RAPUv11_2nd.fg , Rev : 3.0 Ver : 12.14.0
Processing RAWLOADER...
FLIC : 00500020
Req : XSR 1.6
Use RAPUv11_XSR17_alg.fg , Rev : 3.0 Ver : 12.14.0
Processing PASUBTOC ...
Processing ALG ...
Boot Done! :)
TIME : Boot time : 00:00:01
Reopening the connection...
Waiting for response: 30
ADL: Check mode
Select ASIC [C900]
PAPUBkeys : CCD9F80559BA50D9B3E274F9E7120BE1EE4EEA7C
ADL: Preparing for write certificates...

Erase CCC... Ok
Writing CCC... Ok
Erase HWC... Ok
Writing HWC... Ok

ADL: Writing Flash certs done! :)

ADL: Close_Session
Content: 000300000000020000000200000000
ADL: Reboot
All done, disconneting...

Done!

Elapsed: 00:00:14

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
CMLA Key status : CMLA key Not exist

SimLock status : SimLock Damaged!!!!! :(
- > Do REPAIR SL if it SL2/SL phone, if SL3 - Help Only Backup Or RPL


Security status : Security Damaged!!!!! :(
- > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )

-----------------------

PA_SimLock Version :
PA_SL phone detected

Done!

Reading Phone Info....
Connected phone - Nokia E5-00
Software ver : V ICPR82_11w16.3.4 17-08-11 RM-632 (c) Nokia
IMEI : 351663054302617
XappVer : 000007BC
Ape Ver : 081.004
APE Var : 081.004081.004.20.01081.004.C00.01
APE ADSP: 256
DSP Ver : ICPR82_11w16
APE Test: 0.025
PPM :
CNT :
Product SN : 0
Product code :
Long Prod.SN : 0
Hardware info=======
HWID :
Retu : 35
Tahvo : 00
Batery: 3824 mV
APE HW: 256
Lock info ===========
IMEI : 351663054302617
IMEI spNet : 3A 15 66 03 45 03 62 01
IMEI svNet : 33 15 66 03 45 03 62 21 F7

Unable to read Lock table... :(
CRT308 Backup Created

SDD key status : Ok
CMLA Key status : Not Present
SimLock status : Damaged!!!!!
Security status : Damaged!!!!!
PA_SimLock Version :
PA_SL phone detected

User code : Crypted
UserDataExLevel : Low [Gallery] , FullFlash method

Done!

Will Write RPL keys now...
Check RPL file...
SIMLOCK Data found!
SIMLOCK KEY found!
-> Skip Flash keys Part, for Flash Part use Dead Mode!!!!!

Writing SimLock Key... Ok!
Writing SimLock Data... Ok!

SDD Key status : SD Data is Ok
SimLock status : SimLock is Ok
Security status : Security Damaged!!!!! :(


Done!

Connect phone on selected interface...

Phone found!
Series 60 Device detected!
read info... - Ok

Reading Phone Info....
Connected phone - Nokia E5-00
Software ver : V ICPR82_11w16.3.4 17-08-11 RM-632 (c) Nokia
IMEI : 351663054302617
XappVer : 000007BC
Ape Ver : 081.004
APE Var : 081.004081.004.20.01081.004.C00.01
APE ADSP: 256
DSP Ver : ICPR82_11w16
APE Test: 0.025
PPM :
CNT :
Product SN : 0
Product code :
Long Prod.SN : 0
Hardware info=======
HWID :
Retu : 35
Tahvo : 00
Batery: 3824 mV
APE HW: 256
Lock info ===========
IMEI : 351663054302617
IMEI spNet : 3A 15 66 03 45 03 62 01
IMEI svNet : 33 15 66 03 45 03 62 21 F7

Conf key : 0000000000000000
Provider key : 2440700000000000
Country : Finland
Operator : NOKIA (Open)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

SDD key status : Ok
CMLA Key status : Not Present
SimLock status : Ok
Security status : Damaged!!!!!
PA_SimLock Version :
PA_SL3 phone , SP_CODE_LEN : 15

User code : Crypted
UserDataExLevel : Low [Gallery] , FullFlash method

Done!

Local SX4 procedure started...

Check SD : Key is Ok
Phone Imei: 351663054302617
Use custom key...
Step 1...
Step 2...
SX4 Auth fail...
- > "Custom Keys" disabled, try again now
- > If SDD original - "Use Server Sx4"


Local SX4 procedure started...

Check SD : Key is Ok
Phone Imei: 351663054302617
Key file exists, no need to read...
Step 1...
Step 2...
SX4 Auth fail...
- > "Custom Keys" enabled, try again now
- > If SDD original - "Use Server Sx4"


Local SX4 procedure started...

Check SD : Key is Ok
Phone Imei: 351663054302617
Use custom key...
Step 1...
Step 2...
SX4 Auth fail...
- > "Custom Keys" disabled, try again now
- > If SDD original - "Use Server Sx4"


Reading Phone Info....
Connected phone - Nokia E5-00
Software ver : V ICPR82_11w16.3.4 17-08-11 RM-632 (c) Nokia
IMEI : 351663054302617
XappVer : 000007BC
Ape Ver : 081.004
APE Var : 081.004081.004.20.01081.004.C00.01
APE ADSP: 256
DSP Ver : ICPR82_11w16
APE Test: 0.025
PPM :
CNT :
Product SN : 0
Product code :
Long Prod.SN : 0
Hardware info=======
HWID :
Retu : 35
Tahvo : 00
Batery: 3825 mV
APE HW: 256
Lock info ===========
IMEI : 351663054302617
IMEI spNet : 3A 15 66 03 45 03 62 01
IMEI svNet : 33 15 66 03 45 03 62 21 F7

Conf key : 0000000000000000
Provider key : 2440700000000000
Country : Finland
Operator : NOKIA (Open)
Counters : Key 0 [3] , Fbus 0 [10]
Blocks : 7

LOCK STATUS :
=============================
BLK : 1
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 2
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 3
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 4
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 5
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 6
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
BLK : 7
Lock1:Open Lock2:Open Lock3:Open Lock4:Open Lock5:Open
=============================
LOCKS : All Open
=============================
CRT308 Backup Created

SDD key status : Ok
CMLA Key status : Not Present
SimLock status : Ok
Security status : Damaged!!!!!
PA_SimLock Version :
PA_SL3 phone , SP_CODE_LEN : 15

User code : Crypted
UserDataExLevel : Low [Gallery] , FullFlash method

Done!

Как видите никак не хотел SDD восстанавливаться,вернее я предпринимал ошибочные шаги,потом нажал Full PM,и выбрал PM из RPL файла в итоге логи:
Operating mode is OK, no need change...

Field 120
Record 0 write - Ok
Record 1 write - Ok
Record 2 write - Ok
Record 3 write - Ok

Done!

Elapsed: 00:00:00

Local SX4 procedure started...

Check SD : Key is Ok
Phone Imei: 351663054302617
Key file exists, no need to read...
Step 1...
Step 2...
SX4 Auth fail...
- > "Custom Keys" enabled, try again now
- > If SDD original - "Use Server Sx4"


Local SX4 procedure started...

Check SD : Key is Ok
Phone Imei: 351663054302617
Use custom key...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Upload PM checked
Uploading RF/Battery tune to phone...
Using : RM-632.pm
Operating mode is OK, no need change...


Check ST_SECURITY now...
Security status : ST_SECURITY => OK

Done!

Elapsed: 00:00:01

Upload done

Checking StartUp data ...
-----------------------
SDD Key status : SDData is Ok
CMLA Key status : CMLA key Not exist
SimLock status : SimLock is Ok
Security status : Security is Ok
-----------------------

PA_SimLock Version :
PA_SL3 phone , SP_CODE_LEN : 15

Done!

Phone disconected!

Connect phone on selected interface...


Сейчас телефон нормально функционирует.Гляньте логи товарищи,все нормуль?

[KonstantinVoskr]

Вот отлично получилось...Сейчас телефон нормально функционирует.Гляньте логи товарищи,все нормуль?
Ну вроде все нормально, но для пущего спокойствия можете еще прогнать аппарату SelfTest-ы ( если будет ругаться по радиотракту- это нормально).
Ну и погонять его с симкой часик- два тоже стоит, как после обычного восстановления с помощью RPL.

PS: вы свой тот eno файл где откопали то?

[uo5oq]

...
Сейчас телефон нормально функционирует.Гляньте логи товарищи,все нормуль?
Теперь не помешает "поджарить" его, в профессиональном смысле этого слова.

[Сулейман]

PS: хотелось бы узнать контрольную сумму вашего ENO.

Вот контрольная сумма:

CRC32: 3edad08f
MD5: d3f5af521444e4d950356e2257b7da44
SHA-1: 97c6e3ac8c9a585185868411baff699a7ef6ac99

Добавлено через 9 часов 55 минут

PS: вы свой тот eno файл где откопали то?

На одном форуме на ссылку набрел.

Добавлено через 3 минуты
Теперь не помешает "поджарить" его, в профессиональном смысле этого слова.

Сильно не разжаришься,на этом ТА бутер и КП под компаундом.Чистка и прогрев обвязки вокруг USB коннектора решила проблему вроде,т.к.изначально косяк в этом районе был,помните я писал вставил USB шнур и ТА включился,сейчас телефон нормально функционирует думаю больше проблем не будет,завтра отдам клиенту.

[uo5oq]

...Чистка и прогрев обвязки вокруг USB коннектора решила проблему вроде,т.к.изначально косяк в этом районе был,помните я писал вставил USB шнур и ТА включился,сейчас телефон нормально функционирует думаю больше проблем не будет,завтра отдам клиенту.
Если визуально были видны окислы, трещины пайки или прочие повреждения на указанном участке платы, то % на 85 можно считать дефект устранённым.

[Сулейман]

Всем спасибо,тема закрыта!