mortan
17.07.2014, 11:50
Здравствуйте!
Попалась флеш с i9100
с таким логом:
Z3X EasyJtag Software ver. 1.5.8.0
Loading eMMC Addon Firmware... IO: 1850 mV
FW Ver.: 01.50
CMD Pullup Level:1959 mV
CMD Active Level:1907 mV
eMMC Device Information
EMMC CID : 150100303030303030002010021200E6
EMMC CSD : D02701320F5903FFF6DBFFE796404052
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 00/2013 Rev.0x0
EMMC NAME: 000000 , S/N: 537920018
EMMC ROM1 (Main User Data) Capacity: 8192 MB
EMMC ROM2 (Boot Partition 1) Capacity: 1024 kB
EMMC ROM3 (Boot Partition 2) Capacity: 1024 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 1024 kB
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537920018_20140606_2138.extcsd
Done.
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
Z3X EasyJtag Software ver. 1.5.8.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1959 mV
CMD Active Level:1907 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Success
Erasing repair area...
Success
Writing repair area...
Can't write repair area, Reason: CARD Data FIFO Timeout Error
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
===================================
Z3X EasyJtag Software ver. 1.5.8.0
Loading eMMC Addon Firmware... IO: 1850 mV
FW Ver.: 01.50
CMD Pullup Level:1949 mV
CMD Active Level:1887 mV
eMMC Device Information
EMMC CID : 15010030303030303333333302120082
EMMC CSD : D02701320F5903FFF6DBFFE796404052
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 00/2013 Rev.0x33
EMMC NAME: 000003 , S/N: 858980882
EMMC ROM1 (Main User Data) Capacity: 8192 MB
EMMC ROM2 (Boot Partition 1) Capacity: 1024 kB
EMMC ROM3 (Boot Partition 2) Capacity: 1024 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 1024 kB
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000003_ 858980882_20140606_2140.extcsd
Done.
Возможно, ли отремонтировать?
Готов отправить данный экземпляр на опыты, с билетом в одну сторону.
Попалась флеш с i9100
с таким логом:
Z3X EasyJtag Software ver. 1.5.8.0
Loading eMMC Addon Firmware... IO: 1850 mV
FW Ver.: 01.50
CMD Pullup Level:1959 mV
CMD Active Level:1907 mV
eMMC Device Information
EMMC CID : 150100303030303030002010021200E6
EMMC CSD : D02701320F5903FFF6DBFFE796404052
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 00/2013 Rev.0x0
EMMC NAME: 000000 , S/N: 537920018
EMMC ROM1 (Main User Data) Capacity: 8192 MB
EMMC ROM2 (Boot Partition 1) Capacity: 1024 kB
EMMC ROM3 (Boot Partition 2) Capacity: 1024 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 1024 kB
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537920018_20140606_2138.extcsd
Done.
Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
Z3X EasyJtag Software ver. 1.5.8.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1959 mV
CMD Active Level:1907 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Success
Erasing repair area...
Success
Writing repair area...
Can't write repair area, Reason: CARD Data FIFO Timeout Error
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
===================================
Z3X EasyJtag Software ver. 1.5.8.0
Loading eMMC Addon Firmware... IO: 1850 mV
FW Ver.: 01.50
CMD Pullup Level:1949 mV
CMD Active Level:1887 mV
eMMC Device Information
EMMC CID : 15010030303030303333333302120082
EMMC CSD : D02701320F5903FFF6DBFFE796404052
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 00/2013 Rev.0x33
EMMC NAME: 000003 , S/N: 858980882
EMMC ROM1 (Main User Data) Capacity: 8192 MB
EMMC ROM2 (Boot Partition 1) Capacity: 1024 kB
EMMC ROM3 (Boot Partition 2) Capacity: 1024 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 1024 kB
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000003_ 858980882_20140606_2140.extcsd
Done.
Возможно, ли отремонтировать?
Готов отправить данный экземпляр на опыты, с билетом в одну сторону.