schemu
12.06.2014, 08:55
Ищу способ восстановления телефона Huawei MT1-U06, при попытке включения потребление повышается до 300 мА и не изменяется, немного греется модуль процессора с памятью. На сочетание кнопок "громкость +" + "громкость -" + "включение", для входа в рекавери и прошивки, не реагирует.
Собран на процессоре HiSilicon K3V2 (Hi3620) (http://en.wikipedia.org/wiki/HiSilicon#K3V2)
26501
Подключил JTAG по стандартной распиновке часто встречающейся у Huawei, инициализация подключения проходит но память не определяется.
26500
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Exynos 4412 eMMC0 V1.0.4816.63620]
Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is 8 MHz
Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x4BA00477, IR Length = 0x04 bits
Total IR length: 0x0004 bits
Analizing IDCODE(s) of the JTAG scan chain:
1. 0x4BA00477: Generic CORTEX-A9/A15 Core Based Target
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Exynos 4412 eMMC0 V1.0.4816.63620]
Connecting to the dead body...OK
Set I/O Voltage reads as 1.79V, TCK Frequency is 8 MHz
Detected dead body ID: 0x4BA00477
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Custom Target: [CORTEX-A9, 1.80V, TAP0]
Halting target...OK
STATUS: Target is halted.
R0 = 0x00000000 R6 = 0x00000000 R12 = 0x00000000
R1 = 0x00000000 R7 = 0x00000000 R13 = 0x00000000
R2 = 0x00000000 R8 = 0x00000000 R14 = 0x00000000
R3 = 0x00000000 R9 = 0x00000000 R15 = 0x00000000
R4 = 0x00000000 R10 = 0x00000000 CPSR = 0x00000000
R5 = 0x00000000 R11 = 0x00000000
Собран на процессоре HiSilicon K3V2 (Hi3620) (http://en.wikipedia.org/wiki/HiSilicon#K3V2)
26501
Подключил JTAG по стандартной распиновке часто встречающейся у Huawei, инициализация подключения проходит но память не определяется.
26500
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Exynos 4412 eMMC0 V1.0.4816.63620]
Connecting to the target...OK
Set I/O Voltage reads as 1.80V, TCK Frequency is 8 MHz
Following devices are found on the JTAG chain:
Device on TAP #0: ID = 0x4BA00477, IR Length = 0x04 bits
Total IR length: 0x0004 bits
Analizing IDCODE(s) of the JTAG scan chain:
1. 0x4BA00477: Generic CORTEX-A9/A15 Core Based Target
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Resurrector: [Exynos 4412 eMMC0 V1.0.4816.63620]
Connecting to the dead body...OK
Set I/O Voltage reads as 1.79V, TCK Frequency is 8 MHz
Detected dead body ID: 0x4BA00477
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.37, JTAG Manager Version: 1.56
Selected Custom Target: [CORTEX-A9, 1.80V, TAP0]
Halting target...OK
STATUS: Target is halted.
R0 = 0x00000000 R6 = 0x00000000 R12 = 0x00000000
R1 = 0x00000000 R7 = 0x00000000 R13 = 0x00000000
R2 = 0x00000000 R8 = 0x00000000 R14 = 0x00000000
R3 = 0x00000000 R9 = 0x00000000 R15 = 0x00000000
R4 = 0x00000000 R10 = 0x00000000 CPSR = 0x00000000
R5 = 0x00000000 R11 = 0x00000000