HTC Mozart не включается после полного стирания

[mobiSTAR]

До стирания Resurrection проходил, без проблем
решил залить фулл, сделал полное стирание. После этого ничего не хочет делать

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB

есть варианты?

[BRADJGA]

комп ребутни, проводочки уменьши.

[P45]

До стирания Resurrection проходил, без проблем
решил залить фулл, сделал полное стирание. После этого ничего не хочет делать

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB

есть варианты?

я ж ответил на соседнем...
попробуй TCK = 8Mhz

[remark]

Получается что до стирания размер страницы был 4KB а после стирания стал 2KB?
Может глючная нанд?
С какой проблемой пришел телефон?
Посмотрите в логах, до стирания какой был размер страницы?

[mobiSTAR]

комп ребутни, проводочки уменьши.

нет.

Добавлено через 35 секунд
я ж ответил на соседнем...
попробуй TCK = 8Mhz

тцк 8 по дефолту в рифе стоит

Добавлено через 3 минуты
Получается что до стирания размер страницы был 4KB а после стирания стал 2KB?
Может глючная нанд?
С какой проблемой пришел телефон?
Посмотрите в логах, до стирания какой был размер страницы?

получается так
нанд не знаю откуда взять, попробовал бы поменять
KA1000015E-BJTT никто не в курсе где стоит?
тел был рабочий, хотел понизить SPL

логи:
[27.03.2013 11:22:04] [START OPERATION_ID = RESURRECT]
[27.03.2013 11:22:08] Open serial port...OK
[27.03.2013 11:22:08] Connecting to the RIFF Box...OK
[27.03.2013 11:22:08] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 11:22:08] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 11:22:08]
[27.03.2013 11:22:08] Connecting to the dead body...FAILED
[27.03.2013 11:22:08] None is detected.
[27.03.2013 11:22:08] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 11:26:45] [START OPERATION_ID = RESURRECT]
[27.03.2013 11:27:53] Open serial port...OK
[27.03.2013 11:27:53] Connecting to the RIFF Box...OK
[27.03.2013 11:27:53] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 11:27:53] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 11:27:53]
[27.03.2013 11:27:53] Connecting to the dead body...OK
[27.03.2013 11:27:53] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 11:27:53] Set I/O Voltage reads as 3.01V, TCK Frequency is 8 MHz
[27.03.2013 11:27:53]
[27.03.2013 11:27:53] Resurrection sequence started.
[27.03.2013 11:27:53] Establish communication with the phone...OK
[27.03.2013 11:27:53] Initializing internal hardware configuration...OK
[27.03.2013 11:27:53] Uploading resurrector data into memory...OK
[27.03.2013 11:27:53] Starting communication with resurrector...OK
[27.03.2013 11:27:53]
[27.03.2013 11:27:53] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
[27.03.2013 11:27:53] Selected Resurrection Data for the NAND Chip with Page size = 4KB
[27.03.2013 11:27:53]
[27.03.2013 11:27:53] Flashing the dead body...OK
[27.03.2013 11:27:53] Resurrection complete!
[27.03.2013 11:27:53] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 11:28:23] [START OPERATION_ID = RESURRECT]
[27.03.2013 11:29:53] Open serial port...OK
[27.03.2013 11:29:53] Connecting to the RIFF Box...OK
[27.03.2013 11:29:53] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 11:29:53] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 11:29:53]
[27.03.2013 11:29:53] Connecting to the dead body...OK
[27.03.2013 11:29:53] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 11:29:53] Set I/O Voltage reads as 3.01V, TCK Frequency is 8 MHz
[27.03.2013 11:29:53]
[27.03.2013 11:29:53] Resurrection sequence started.
[27.03.2013 11:29:53] Establish communication with the phone...OK
[27.03.2013 11:29:53] Initializing internal hardware configuration...OK
[27.03.2013 11:29:53] Uploading resurrector data into memory...OK
[27.03.2013 11:29:53] Starting communication with resurrector...OK
[27.03.2013 11:29:53]
[27.03.2013 11:29:53] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
[27.03.2013 11:29:53] Selected Resurrection Data for the NAND Chip with Page size = 4KB
[27.03.2013 11:29:53]
[27.03.2013 11:29:53] Flashing the dead body...OK
[27.03.2013 11:29:53] Resurrection complete!
[27.03.2013 11:29:53] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 11:33:54] [START OPERATION_ID = RESURRECT]
[27.03.2013 11:33:57] Open serial port...OK
[27.03.2013 11:33:57] Connecting to the RIFF Box...OK
[27.03.2013 11:33:57] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 11:33:57] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 11:33:57]
[27.03.2013 11:33:57] Connecting to the dead body...FAILED
[27.03.2013 11:33:57] None is detected.
[27.03.2013 11:33:57] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:06:28] ------------------------------- JTAG Manager Session Closed -------------------------------



[27.03.2013 12:23:12] ------------------------------- JTAG Manager Session Opened -------------------------------
[27.03.2013 12:23:12] JTAG Manger Version: 1.48
[27.03.2013 12:23:12] -------------------------------------------------------------------------------------------


[27.03.2013 12:26:40] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:26:53] Open serial port...OK
[27.03.2013 12:26:53] Connecting to the RIFF Box...OK
[27.03.2013 12:26:53] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:26:53] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:26:53]
[27.03.2013 12:26:53] Connecting to the dead body...OK
[27.03.2013 12:26:53] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:26:53] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:26:53]
[27.03.2013 12:26:53] Resurrection sequence started.
[27.03.2013 12:26:53] Establish communication with the phone...OK
[27.03.2013 12:26:53] Initializing internal hardware configuration...OK
[27.03.2013 12:26:53] Uploading resurrector data into memory...OK
[27.03.2013 12:26:53] Starting communication with resurrector...OK
[27.03.2013 12:26:53]
[27.03.2013 12:26:53] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
[27.03.2013 12:26:53] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:27:02] [START OPERATION_ID = DCC_ERASE_MEMORY]
[27.03.2013 12:27:16] Open serial port...OK
[27.03.2013 12:27:16] Connecting to the RIFF Box...OK
[27.03.2013 12:27:16] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:27:16] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:27:16]
[27.03.2013 12:27:16] Connecting to the dead body...OK
[27.03.2013 12:27:16] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:27:16] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:27:16] Settings Code: 0x05010B00000000400000000001400000
[27.03.2013 12:27:16]
[27.03.2013 12:27:16] Resurrection sequence started.
[27.03.2013 12:27:16] Establish communication with the phone...OK
[27.03.2013 12:27:16] Initializing internal hardware configuration...OK
[27.03.2013 12:27:16] Uploading resurrector data into memory...OK
[27.03.2013 12:27:16] Starting communication with resurrector...OK
[27.03.2013 12:27:16]
[27.03.2013 12:27:16] Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
[27.03.2013 12:27:16]
[27.03.2013 12:27:16] Erasing FLASH1 memory from 0x000000000000 to 0x00001FFFFFFF...OK
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000. Attempt to Repeat again.
[27.03.2013 12:27:16] WARNING: Erasing Error (0x24) at 0x000017A40000 is Ignored. Erase continues.
[27.03.2013 12:27:16] Completed in 00:00:11.438 (Average Transfer Rate: 45837.38 kB/s)
[27.03.2013 12:27:16] [FINISH OPERATION_ID = DCC_ERASE_MEMORY]

[27.03.2013 12:27:22] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:27:27] Open serial port...OK
[27.03.2013 12:27:27] Connecting to the RIFF Box...OK
[27.03.2013 12:27:27] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:27:27] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:27:27]
[27.03.2013 12:27:27] Connecting to the dead body...OK
[27.03.2013 12:27:27] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:27:27] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:27:27]
[27.03.2013 12:27:27] Resurrection sequence started.
[27.03.2013 12:27:27] Establish communication with the phone...OK
[27.03.2013 12:27:27] Initializing internal hardware configuration...OK
[27.03.2013 12:27:27] Uploading resurrector data into memory...OK
[27.03.2013 12:27:27] Starting communication with resurrector...OK
[27.03.2013 12:27:27]
[27.03.2013 12:27:27] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:27:30] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:27:50] Open serial port...OK
[27.03.2013 12:27:50] Connecting to the RIFF Box...OK
[27.03.2013 12:27:50] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:27:50] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:27:50]
[27.03.2013 12:27:50] Connecting to the dead body...OK
[27.03.2013 12:27:50] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:27:50] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:27:50]
[27.03.2013 12:27:50] Resurrection sequence started.
[27.03.2013 12:27:50] Establish communication with the phone...OK
[27.03.2013 12:27:50] Initializing internal hardware configuration...OK
[27.03.2013 12:27:50] Uploading resurrector data into memory...OK
[27.03.2013 12:27:50] Starting communication with resurrector...OK
[27.03.2013 12:27:50]
[27.03.2013 12:27:50] ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB
[27.03.2013 12:27:50] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:28:09] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:28:14] Open serial port...OK
[27.03.2013 12:28:14] Connecting to the RIFF Box...OK
[27.03.2013 12:28:14] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:28:14] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:28:14]
[27.03.2013 12:28:14] Connecting to the dead body...OK
[27.03.2013 12:28:14] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:28:14] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:28:14]
[27.03.2013 12:28:14] Resurrection sequence started.
[27.03.2013 12:28:14] Establish communication with the phone...OK
[27.03.2013 12:28:14] Initializing internal hardware configuration...OK
[27.03.2013 12:28:14] Uploading resurrector data into memory...OK
[27.03.2013 12:28:14] Starting communication with resurrector...OK
[27.03.2013 12:28:14]
[27.03.2013 12:28:14] ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB
[27.03.2013 12:28:14] [FINISH OPERATION_ID = RESURRECT]

[27.03.2013 12:28:44] [START OPERATION_ID = RESURRECT]
[27.03.2013 12:28:50] Open serial port...OK
[27.03.2013 12:28:50] Connecting to the RIFF Box...OK
[27.03.2013 12:28:50] Firmware Version: 1.34, JTAG Manager Version: 1.48
[27.03.2013 12:28:50] Selected Resurrector: [HTC Mozart V1.00]
[27.03.2013 12:28:50]
[27.03.2013 12:28:50] Connecting to the dead body...OK
[27.03.2013 12:28:50] Detected dead body ID: 0x202400E1 - CORRECT!
[27.03.2013 12:28:50] Set I/O Voltage reads as 2.99V, TCK Frequency is 8 MHz
[27.03.2013 12:28:50]
[27.03.2013 12:28:50] Resurrection sequence started.
[27.03.2013 12:28:50] Establish communication with the phone...OK
[27.03.2013 12:28:50] Initializing internal hardware configuration...OK
[27.03.2013 12:28:50] Uploading resurrector data into memory...OK
[27.03.2013 12:28:50] Starting communication with resurrector...OK
[27.03.2013 12:28:50]
[27.03.2013 12:28:50] ERROR: No Resurrection Data is available for the NAND Chip with Page size = 2KB
[27.03.2013 12:28:50] [FINISH OPERATION_ID = RESURRECT]

[remark]

Есть бредовая идея, поробовать залить небольшой кусочек фула через вкладку "JTAG Read/Write", а потом пробовать лить фул через DCC...

[mobiSTAR]

Есть бредовая идея, поробовать залить небольшой кусочек фула через вкладку "JTAG Read/Write", а потом пробовать лить фул через DCC...

не идет

[remark]

не идет
лог?

[mobiSTAR]

лог?
[27.03.2013 12:55:37] Writting FLASH1 memory from 0x000000000000 to 0x00001FFFFFFF
[27.03.2013 12:55:37] WARNING: Programming Error (0x24) at 0x000000000000. Attempting to Repeat.
[27.03.2013 12:55:37] WARNING: Programming Error (0x24) at 0x000000000000. Attempting to Repeat.
[27.03.2013 12:55:37] WARNING: Programming Error (0x24) at 0x000000000000. Attempting to Repeat.
[27.03.2013 12:55:37] WARNING: Programming Error (0x24) at 0x000000000000. Attempting to Repeat.
[27.03.2013 12:55:37] WARNING: Programming Error (0x24) at 0x000000000000. Attempting to Repeat.
[27.03.2013 12:55:37] WARNING: Programming Error (0x24) at 0x000000000000. Attempting to Repeat.
[27.03.2013 12:55:37] ERROR: Timeout while waiting for DCC Loader response. Trying to recover...FAILED
[27.03.2013 12:55:37] ERROR: Failed due to multiple communication errors. Terminating at 0x000000000000
[27.03.2013 12:55:37] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]

[remark]

Это лог попытки записи через вкладку DCC.
Я же предлагаю отрезать от фула в Hex редакторе к примеру первые 1MB (0x00100000) и поробовать залить этот кусочек через вкладку JTAG Read/Write, т.е. Direct write, без лодера.
И если эта операция пройдет успешно, опять попробовать шить через DCC.

[Shadow_user]

А не кого не смущает что в последнем логе нет размера Nand ни ID Flash.
Есть большая вероятность отвала или смерти последней.

[remark]

А не кого не смущает что в последнем логе нет размера Nand ни ID Flash.
Есть большая вероятность отвала или смерти последней.

Топикстартер режет логи, не известно что было выше.

[aspir]

ID: 0x202400E1
с этой печкой любой ремонт надо начинать с перекатки пары.

[mobiSTAR]

перекатал пару,то же самое. Думаю нужна NAND

Кто подскажет, откуда можно снять?
KA1000015E-BJTT

[Shadow_user]

Google при введении в поиск ID: 0x00EC/0x66BC, дал три результата: HTC Explorer, HTC Mozart, htc Wildfire S

[mobiSTAR]

Google при введении в поиск ID: 0x00EC/0x66BC, дал три результата: HTC Explorer, HTC Mozart, htc Wildfire S

негусто, но все равно спасибо