PDA

Просмотр полной версии : [Вопрос] C3530 не прошивается до конца


Tiburon
10.02.2011, 15:12
Принесли после каких-то манипуляций с прошивкой (видимо пытались обновить через KIes),при включении на белом экране голубые иконки телефона,компьютера и восклицательный знак.
Комплект для прошивки взял тут:http://www.mcrf.ru/forum/showpost.php?p=216658&postcount=11
Шется и из выключенного состояния и из режима "голубых иконок",ошибка одна и таже на двух компах.


Device synchronized.
Injecting EBL
Boot-loader is active
EBL version: 6180_Bootloader_10.0_MKEYSKEY 10..0
Boot mode is: BB
Using: Faster CRC, Writing all blocks
Package length is 2048 - protocol: 1.16
Baud rate set to 921600
Get flash id.
CFI stage 1
Flash ID is: 220800EC
CFI stage 2
Boot process finished

Start downloading item 'CODE:catfish.fls'' from file 'D:\C3530XXJK3\C3530XXJK3_bin.fls''.
Sending sec-pack.
Load region 0
Use flash pre-erase.
Sending data.
WARNING: Target EBL does not support NVM handling
Sending end-pack.
Checksum OK (0x924D)
Verify OK
Process time was 3 min 55 sec.

Start downloading item 'CODE:catfish.fls'' from file 'D:\C3530XXJK3\C3530XXJK3_cds.fls''.
Sending sec-pack.
Load region 0
Use flash pre-erase.
Sending data.
WARNING: Target EBL does not support NVM handling
Sending end-pack.
Checksum OK (0x485D)
Verify OK
Process time was 2500 msec.

Start downloading item 'CODE:temp_UI_IMAGE.fls'' from file 'D:\C3530XXJK3\C3530XXJK3_ui_image.fls''.
Sending sec-pack.
Load region 0
Use flash pre-erase.
Sending data.
WARNING: Target EBL does not support NVM handling
Sending end-pack.
Checksum OK (0x749B)
Verify OK
Process time was 22.1 sec.

Start downloading item 'BOOT CORE SLB:dwdtoolsrc/bootcore/make/.output/XMM6180_EHS2AGR_CATFISH_ROU_CARDINAL/fls/psi_flash.fls'' from file 'D:\C3530XXJK3\psi_flash.fls''.
Sending sec-pack.
Load region 0
Use flash pre-erase.
Sending data.
Sending end-pack.
Checksum OK (0xE734)
Verify OK
Process time was 2297 msec.

Start downloading item 'CUST:temp_GT-C3530_SER.dffs'' from file 'D:\C3530XXJK3\C353FSERJL2_csc.dffs''.
Sending sec-pack.
Load region 0
Use flash pre-erase.
Sending data.
Process time was 2 min 36 sec.

Stopped at 74% total, 71% current
Timeout occured during packet reception
The phone did not answer within the timeout period. This could be that the communication is interrupted or that the target SW is in an endless loop.
Check the connection to the phone, battery etc. If the problem persists report the error to the developer.
Channel 1 is succesfully closed.

Burzum
10.02.2011, 18:34
Скрин прошивки можно бы выложить.