sphinxxx
17.01.2008, 06:31
Слил бэкап, прошил прошивкой с саппорта (пробовал две). Делал full format в инифинити. Safe формат не проходит ни в инфинити, ни во флештуле, также как и format ffs в инифинити.
Это инфо:
-----------
COM7 [VCP6] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND: Hynix HY27XS08121M 512+16 32 pages, 66Mb
NAND id: AD76AD76
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 1000
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:007600AD0076 [04200000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page+spare
converting data...
done 0x00010000 bytes
identification#1 protocol ver: 04
ver. sw1: U6_PCB04_GPRS_MT6228_S02.U6V10B32.BIN
ver. sw2: U6V10B32
ffs offset/size: 01700000/02900000
id-page Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Finished, time used: 38 sec
Remove/Install battery now !
Это format ffs:
-----------------
COM7 [VCP6] selected
Action: reset settings
Model: Autodetect 6228 NAND
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200
Initializing[6228:8A02:8A02]...
CPU: MT6228
chip: 0031:0000:0101
Connecting, wait... -
(здесь тел включается и бежит прогресс-бар)
error: can't finalize test mode
repeat operation and HOLD phone "Power" button long time !
error: operation failed !
Finished, time used: 27 sec
Remove/Install battery now !
То же самое и при safe format.
Кнопку включения ессно держу все время, пока бутится.
Тел пропаивал.
Кто встречал такое?
Это инфо:
-----------
COM7 [VCP6] selected
Device: Autodetect 6228 NAND
Checking data, wait...
Action: read/check detailed information
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6228:8A02:8A02]...
CPU: MT6228
chip: 0031:0000:0101
boot step size: 0400
Release Power button now !
Boot Done
Initialize...
version: 3.1
loader: 3.1.02
NAND: Hynix HY27XS08121M 512+16 32 pages, 66Mb
NAND id: AD76AD76
page size: 200+10
pages/block: 20
bits i/o: 08
address cycles: 04
blocks: 1000
ram size: 00800000
NOR: 0000:000000000000 [00000000]
NAND: 00AD:007600AD0076 [04200000]
NOR chip is not installed
Initialize Done
Set baud...
921600
Set baud Done
Identification...
reading structure area...
detecting structure...
source data: page+spare
converting data...
done 0x00010000 bytes
identification#1 protocol ver: 04
ver. sw1: U6_PCB04_GPRS_MT6228_S02.U6V10B32.BIN
ver. sw2: U6V10B32
ffs offset/size: 01700000/02900000
id-page Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
Finished, time used: 38 sec
Remove/Install battery now !
Это format ffs:
-----------------
COM7 [VCP6] selected
Action: reset settings
Model: Autodetect 6228 NAND
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200
Initializing[6228:8A02:8A02]...
CPU: MT6228
chip: 0031:0000:0101
Connecting, wait... -
(здесь тел включается и бежит прогресс-бар)
error: can't finalize test mode
repeat operation and HOLD phone "Power" button long time !
error: operation failed !
Finished, time used: 27 sec
Remove/Install battery now !
То же самое и при safe format.
Кнопку включения ессно держу все время, пока бутится.
Тел пропаивал.
Кто встречал такое?