alleksan
14.06.2007, 12:34
сделал разблокировку юзера инфинити, во время процесса записи еепром выдал ошибку записи.
Бекап еепром и фул сохранил, но ни один ни другой до конца не льются.
вот лог прошивки фула
COM49 selected
Device: Autodetect
Checking data, wait...
advanced flash detection active
Action: write flash
"smart write" active
write: Firmware
skip: Customization
skip: Language Pack
skip: Eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6219:8A01]...
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: B000B101000000
flash: B000B100000000
flash: Sharp Intel std [def 0008x002000 007Fx010000] 8Mb
detecting chip #01 in region #00...
flash: B000B004000000
flash: B000B000000000
flash: Sharp Intel std [def 007Fx010000 0008x002000] 8Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
230400
Set baud Done
Check space...
operation mode: Complete detection mode
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: B000B101000000
flash: B000B100000000
flash: Sharp Intel std [def 0008x002000 007Fx010000] 8Mb
detecting chip #01 in region #00...
flash: B000B004000000
flash: B000B000000000
flash: Sharp Intel std [def 007Fx010000 0008x002000] 8Mb
number of flash chip/regions detected: 02/01
total flash region size: 01000000
detecting eeprom area in 2 chip(s)...
flash: B000B101000000
flash: B000B100000000
checking area[00000000]: 00000000-007FFFFF...
flash: B000B004000000
flash: B000B000000000
checking area[00800000]: 00000000-007FFFFF...
eeprom found near: 00E80000
Detected eeprom address is non-standard: 00E80000
If you are not sure that detected address is correct:
1. press "NO" right now
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address confirmed by user
detecting eeprom size...
eeprom size: 00180000
eeprom chip: 01
eeprom area detected[00800000]: 00680000-007FFFFF
detect device identification, method #1...
detection phase #1...
.
detection phase #2...
.................................................. ..............
warning: identification information not found, possible reasons:
.old firmware type w/o identification
.damaged firmware
.damaged hardware
detection phase #3...
.................................................. ..............
detect device parameters finished
flash: B000B101000000
flash: B000B100000000
Check space Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
Area: Firmware
flash: B000B101000000
flash: B000B100000000
Write: Firmware
jump to next chip[01]
flash: B000B004000000
flash: B000B000000000
Write: Firmware
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
Write Fail
Finished, time used: 323 sec
Remove/Install battery now !
Бекап еепром и фул сохранил, но ни один ни другой до конца не льются.
вот лог прошивки фула
COM49 selected
Device: Autodetect
Checking data, wait...
advanced flash detection active
Action: write flash
"smart write" active
write: Firmware
skip: Customization
skip: Language Pack
skip: Eeprom
Boot...
Press and HOLD Power button now !
baud autodetection active
19200
Connecting, wait...
Initializing[6219:8A01]...
Release Power button now !
Boot Done
Initialize...
detecting chip #00 in region #00...
flash: B000B101000000
flash: B000B100000000
flash: Sharp Intel std [def 0008x002000 007Fx010000] 8Mb
detecting chip #01 in region #00...
flash: B000B004000000
flash: B000B000000000
flash: Sharp Intel std [def 007Fx010000 0008x002000] 8Mb
number of flash chip/regions detected: 02/01
Initialize Done
Set baud...
230400
Set baud Done
Check space...
operation mode: Complete detection mode
device parameters autodetection in progress..
detecting chip #00 in region #00...
flash: B000B101000000
flash: B000B100000000
flash: Sharp Intel std [def 0008x002000 007Fx010000] 8Mb
detecting chip #01 in region #00...
flash: B000B004000000
flash: B000B000000000
flash: Sharp Intel std [def 007Fx010000 0008x002000] 8Mb
number of flash chip/regions detected: 02/01
total flash region size: 01000000
detecting eeprom area in 2 chip(s)...
flash: B000B101000000
flash: B000B100000000
checking area[00000000]: 00000000-007FFFFF...
flash: B000B004000000
flash: B000B000000000
checking area[00800000]: 00000000-007FFFFF...
eeprom found near: 00E80000
Detected eeprom address is non-standard: 00E80000
If you are not sure that detected address is correct:
1. press "NO" right now
2. make flash backup for emergency case
3. repeat required operation
Are you sure that detected eeprom address is correct ?
autodetected eeprom address confirmed by user
detecting eeprom size...
eeprom size: 00180000
eeprom chip: 01
eeprom area detected[00800000]: 00680000-007FFFFF
detect device identification, method #1...
detection phase #1...
.
detection phase #2...
.................................................. ..............
warning: identification information not found, possible reasons:
.old firmware type w/o identification
.damaged firmware
.damaged hardware
detection phase #3...
.................................................. ..............
detect device parameters finished
flash: B000B101000000
flash: B000B100000000
Check space Done
Manipulation...
Manipulation Done
Finalization...
Finalization Done
Write...
Area: Firmware
flash: B000B101000000
flash: B000B100000000
Write: Firmware
jump to next chip[01]
flash: B000B004000000
flash: B000B000000000
Write: Firmware
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
error: error# 000000B0
20:5[01]: Erase fail or program sequence error when set with SR[4,7].
10:4[01]: Program fail or program sequence error when set with SR[5,7].
error: flash write error: 00E12000:00002000
Write Fail
Finished, time used: 323 sec
Remove/Install battery now !